Download
Share
Print this page
Toro TITAN ZX4820 Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower
  5. 74920 TITAN ZX4820
  6. Manual
Toro TITAN ZX4820 Manual

Toro TITAN ZX4820 Manual

Hide thumbs Also See for TITAN ZX4820:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
TITAN ZX4820 and ZX5420 Zero-Turn-Radius Riding
Mower
Model No. 74920—Serial No. 312000001 and Up
Model No. 74924—Serial No. 312000001 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
© 2012—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Rollbar
Rollbar support
Pivot bracket
Flat spacer
Pivot pin with hairpin and lanyard
Reinforcing bracket
Large washer
Bolt (1/2 x 4–1/2 inches)
Bolt (1/2 x 3–1/2 inches)
Cylindrical spacer
Flat washer (1/2 inch)
Flange locknut (1/2 inch)
Hex locknut (1/2 inch)
Flange locknut (5/16 inch, may be
pre-installed)
Conical rubber bumper (may be
pre-installed)
Small rubber bumper (may be
pre-installed)
Bolt (5/16 x 3–3/4 inch)
Flat washer (5/16 inch)
Flange locknut (5/16 inch)
Hose coupling (not included with CE
models)
Cut off baffle (CE models only)
Bolt (5/16 x 5/8 inch, 54 inch CE units
only)
Ignition Key
Operator's Manual
Engine Operator's Manual
Operator Training Material
Register at www.Toro.com.
Form No. 3372-849 Rev A
Qty.
–
Connect the battery.
–
Set up the motion control levers.
1
2
4
4
2
2
4
2
8
2
Install the Roll Over Protection System
4
(ROPS).
8
2
2
2
2
2
2
2
1
1
2
Complete the setup.
1
1
1
1
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved

Advertisement

loading

Related Manuals for Toro TITAN ZX4820

Summary of Contents for Toro TITAN ZX4820

  • Page 1 Form No. 3372-849 Rev A TITAN ZX4820 and ZX5420 Zero-Turn-Radius Riding Mower Model No. 74920—Serial No. 312000001 and Up Model No. 74924—Serial No. 312000001 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped.

  • Page 2: Connecting The Battery

    Note: Determine the left and right sides of the machine from the normal operating position. Connecting the Battery No Parts Required Procedure 1. Locate the battery and negative battery cable in the center of the machine. G010257 2. Remove the black plastic cap from the negative Figure 1 battery post.
  • Page 3 G010258 Figure 2 A. With the motion control levers in the outward, neutral lock position, remove the hairpin cotters on the seat rod securing the seat to the machine. B. Slide the seat rod out from the brackets and seat frame. C.

  • Page 4: Installing The Roll Over Protection System (Rops)

    Installing the Roll Over Protection System (ROPS) Parts needed for this procedure: Rollbar Rollbar support Pivot bracket Flat spacer Pivot pin with hairpin and lanyard g017895 Reinforcing bracket Large washer Figure 4 Bolt (1/2 x 4–1/2 inches) 1. Bolt (1/2 x 3–1/2 inches) 9.

  • Page 5: Making Final Adjustments

    Note: Ensure that the tab to which the lanyard is attached is angled away from the surface of the pivot bracket. Figure 5 1. Bolt (1/2 x 3–1/2 inches) 4. Flat spacer (4) 2. Flat washer (4) 5. Flange locknut (4) 3.

  • Page 6: Completing The Setup

    Sequence Description Torque Three bolts on each 400 ± 40 in-lbs side attaching the (45 ±.4 N-m) pivot brackets to the rollbar and rollbar support. Ensure that the tab to which the lanyard is attached is pointed upward. Two bolts on each 300 ±...
  • Page 7 Checking the Tire Pressure Check the front and rear tires for proper inflation. Refer to Checking the Tire Pressure in the Operator's Manual for the recommended inflation pressure. Checking the Side Discharge Chute Remove the packing restraint holding the side discharge chute up and lower the chute into place.

This manual is also suitable for:

Titan zx54207492074924