Using - Panasonic NI -FS770 Operating Instructions Manual

Using

1. Place the iron on the
①
2
base securely.
② Plug the power plug
into the electrical
3
outlet.
③ Slide the power switch to
" I " position.
The "HIGH（台灣：高）" indicator
lights up and starts blinking.
SET button
2. Press the Set button to start setting
the temperature.
• Each time the SET button is pressed,
the indicators are switched once in the
order of "HIGH" → "MED" →"LOW"
(台灣："高"→"中"→"低").
(HongKong)
• When the product gets ready to work, the set indicator will
light on in red. (The figure shows the case when "HIGH
(台灣：高）" is set.)
About 19
seconds later
(HongKong) (Taiwan) (HongKong) (Taiwan)
[The indicator blinks [The indicator stays on
in red (once/2s): in red: ready to work]
in preparation]
10
2. When the powerful steam indicator starts illuminating,
press the steam button continuously for using steam
functions.
・ It is available for about 10 minutes of steam usage.
(The time may vary depending on usages.).
・
When used as a horizontal steam iron (refer to page 14),
it's more effective in wrinkle removal after the power
indicator light stops flashing around 20 seconds.
1
Refer to "After each use" in " Storing " on P14
Notes：
a. Iron the garment directly by pressing the soleplate against
it or with steam by keeping the soleplate slightly away from
it, depending on its material.
b. The iron can be used as dry iron without the steam button
pressed.
c. When the steam button is pressed, the water pump will
pump water into the tank. There will be slight noise and
(Taiwan)
vibration, which are normal.
d. Some noises which can be heard when shaking the iron
is the one made when a pipe hits the tank. This is normal.
e. There could be white powder/particles coming out of the
steam vents while using the steam function. They are
minerals found in hard water which can be brushed off.
This is normal.
f. The steam will be invisible occasionally, depending on
the ambient temperature and indoor brightness.
g. The water will flow from the ventage when the water inlet
is facing down.
h. If the water in tank is used out during ironing, turn off the
power, unplug the power plug and add water.
Ironing methods and temperature settings
Types of fiber and corresponding usage method.
Ironing recommendations
Press the Keep the
soleplate soleplate
Fabric
against slightly away
the from the
garment garment
Velvet
Silk
N/A
Acrylic
Polyester
HIGH is recommended
Man-made fiber
MED (MED is also
Wool applicable)
Linen
cotton
HIGH
(Including blended
yarn fabrics)
• Set the temperature according to the label on the clothes.
• When you are ironing delicate fabrics or creating a fluffy effect,
keep the soleplate slightly away from the garment.
• To achieve a good ironing effect, press the soleplate against
the garment. Please check the laundry care label on the
garment before setting "HIGH" or "MED" .
• Please iron the garments in the order from those labeled "Iron
on low heat" to those labeled "Iron on high heat". It may take
several minutes for the setting to change from HIGH to LOW.
• Keep the soleplate away from the clothes when ironing clothes
labeled "Iron with cover".
• You can iron any kind of clothes by keeping the soleplate away
from the clothes.
• The recommended moving speed of the soleplate is about
10 cm every 3 seconds.
• Do not use the product on leather products.
• To iron heat-sensitive materials or dark-colored fabrics, test
on a small corner of the fabric before ironing the entire
garment to avoid damages.
• Do not iron clothes labeled "No steam".
Types of fiber and corresponding usage method.
HIGH
MED
LOW
(HongKong) (Taiwan)
HIGH: Powerful steam is emitted at a speed of about 11 g/min.
MED : Normal steam is emitted at a speed of about 9 g/min.
LOW : No steam is emitted.
Notes:
a. Ironing a man-made fiber garment for a long time may
cause shrinkage of the garment.
b. It may take several minutes for the setting to change from
"HIGH" to "MED" or "LOW" . (The product is ready to work
when the red indicator stops blinking.)
c. When "MED" is set, the temperature regulator in the
product will act, and thus the amount of steam will be
temporarily reduced.
d. To deodorize a garment, set the temperature to "HIGH".
While keeping the soleplate slightly away from the garment,
use steam to iron the part to be deodorized for 10 seconds.
11