Sealey AK2952 Instructions

Thank you for purchasing a Sealey Product. Manufactured to a high standard this tool will, if used according to these instructions and properly
maintained, give years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
F WARNING! Ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using the torch.
Familiarise yourself with the application and limitations, as well as the potential hazards, peculiar to the tool.
!
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
!
DO NOT repair the torch yourself, use an authorised service agent.
&
F
WARNING! Use and handle the butane gas (lighter fuel) in accordance with the instructions supplied with the fuel.
p
Butane gas is highly flammable, so keep an appropriate fire extinguisher close to hand.
!
Ensure there are no flammable or combustible materials near the work area.
!
Keep the work area clean, uncluttered and ensure there is adequate ventilation and lighting.
!
Keep children and unauthorised persons away from the working area.
!
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/or tie back long hair.
!
Point the torch away from yourself and others when igniting flame.
!
Keep hands and body clear of the torch head when operating as it becomes very hot.
!
Secure unstable workpiece with a clamp, vice or other adequate holding device.
!
Always use the integral stand when torch is not in use.
!
DO NOT get the torch wet.
&
DO NOT use torch where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc.
&
DO NOT use the torch for any purpose other than for which it is designed.
&
DO NOT use accessories other than those supplied with, or manufactured specifically for use with, the torch.
&
F WARNING! DO NOT touch the torch head during, or immediately after, use. Allow the torch to cool naturally before handling.
p
DO NOT cool the torch in water.
&
DO NOT point the torch at yourself, others, or animals.
&
DO NOT operate the torch when you are tired, or under the influence of alcohol, drugs or intoxicating medication.
&
DO NOT allow untrained persons to operate the torch.
&
DO NOT operate the torch if any parts are damaged or missing as this may cause failure and/or personal injury.
&
DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.
&
DO NOT leave the torch, after use, until it has cooled.
&
When work is complete, allow the torch to cool. Clean the torch and accessories, return to case and store in a safe, dry childproof location.
!
DO NOT store in direct sunlight or where the temperature could exceed 104
&
F
WARNING! Failure to use the torch correctly may result in fire, damage and/or personal injury.
p
I
DANGER! The flame is invisible in sunlight - be extremely cautious.
s
2. INTRODUCTION
The AK2952 torch is portable and lightweight, suitable for heating, soldering, shrinking and many other applications. Powered by butane gas
(lighter fuel), the torch has slide switch ignition and automatic flame selection to give quick and clean operation.
AK2952 Kit comprises: Torch, Soldering Head, Solder Tip x 3, Hot Air Nozzle, Deflector Nozzle, Probe, Hot Knife, Stand and Sponge, Safety Cap.
3. OPERATING INSTRUCTIONS
F WARNING! Ensure you have read and understood the safety instructions in Section 1 before using the torch.
p
Note: The torch is supplied without butane gas. Before use it must be fuelled as follows:
3.1. TO FUEL THE TORCH
3.1.1. Use only high quality butane gas (lighter fuel) to fill the torch.
3.1.2. Ensure the ‘On/Off’ switch is in the ‘Off’ position. See fig. 1, ‘On/Off’ Safety Switch.
3.1.3. Follow the instructions on the butane fuel can.
3.1.4. Apply the can filler tip to the torch base filler valve (figs. 1 & 2). Use a pumping action for best filling results.
3.1.5. Once full, allow gas in the torch to stand and stabilise for a few minutes before use.
fig. 1
INSTRUCTIONS FOR:
MULTI-FUNCTION BUTANE SOLDERING/HEATING
TOOL SET
F/40
O
Model:
C
O
fig. 2
AK2952
AK2952 - 2 - 190503