Eureka Forbes Aquaguard Classic+ UV+Hot User Manual page 3

AQUAGUARD SELECT
®
TM
A unique combination of
*
naturally occurring vital
minerals like Calcium,
Magnesium, Copper, and
Zinc with anti-microbial
carbon granules.
AQUAGUARD SELECT CLASSIC + UV HOT
®
Aquaguard
6.2 kgs. (Approx.)
Combination Cartridge, UV Lamp, Active
Copper Maxx
Flow Rate (Approx.) Ambient Water: 1.5 Liters / min @ 1bar pressure
Hot / Warm water : 1 Liter / min @ 1 bar pressure
150V AC to 280V AC, 50Hz
External: 230V AC, Internal: 12V DC, 1.7 Amps
20 Watts max in Ambient mode & 775 Watts in
Hot / Warm mode
11 Watts
HOT TANK DETAILS
Tank Volume
500 ml.
Temperature Sensing
Thermistor (Electronic Thermostat)
Input Iron (max.) 0.3 PPM
0.2 PPM
Up to 200 PPM
UV HOT
VOCs
Enhances the taste of the water and
increases the level of essential minerals
which helps in improved health and
body functions. At the same time,
balancing the pH of water, making it
healthy.
®
Select Classic + UV HOT
Cartridge, Biotron Cartridge
TM TM
INDICATION CHART TO USE
CLASSIC + UV HOT
SELECT
Indication Unit Status
Power On - All LEDs will blink for 1 sec in Blue, Yellow
and Red.
Purification Process
Warm Mode ON
Hot Mode ON
Ready to dispense - All LEDs become solid.
Blue - Ambient Water
Yellow - Warm Water
Red - Hot Water
Dispensing - Touch the centre of LED indication;
single LED rotates clockwise.
Blue - Ambient Water
Yellow - Warm Water
Red - Hot Water
EA Fault:
7 5
LED 2, 5 & 7 will be solid
6 3
LED 1, 3 or only 1 or 3 will blink @0.5 second rate
4 1
depending on the filters.
2
Sleep Mode - If unit is not in use for 10 minutes, unit
goes to sleep mode. To activate, touch the centre of
LED indication.
Flush - Touch and hold centre of LED indication for
10 seconds. LEDs rotate anti-clockwise. To stop flushing,
touch the centre of LED indicator again.
(Caution: Do not drink the water which comes out during
flushing mode).
Filter life warning/End of life.
Switch off the power and water supply, if unit is not used for 3-4 hours.
OFF
Aquaguard Select
®
Aquaguard Select
®
Aquaguard Select
®
• To get hot / warm water, touch the respective switches
Aquaguard Select
®
Aquaguard Select
®
Aquaguard Select
®
• Do not overflow the glass container with hot water
AQUAGUARD
®
Indication Unit Status
Temperature sensor fault
All LEDs will blink in Red at 0.5 sec rate.
UV Fault / LDR Fault
0.5sec 0.5sec
All LEDs ON for 0.5 seconds and OFF for 3 seconds.
3sec 3sec
SV Fault
0.5sec 0.5sec 0.5sec 0.5sec
All LEDs ON, OFF, ON for 0.5 seconds and then OFF
for 3 seconds. Cycle repeats.
0.5sec 3sec 0.5sec
EA fault (if both 2 EA chip not connected or if main PCB
to junction PCB harness is not connected) LED 2, 5 & 7
is solid. LED 1, 3 blinks @0.5 second rate.
Combination
Cartridge EA fault (Blue) LED 2, 5 & 7 is solid.
LED 3 blinks @0.5 second rate.
Active Copper cartridge EA fault (Beige)
LED 2, 5 & 7 is solid. LED 1 blinks @0.5 second rate.
Aquaguard Select
®
Aquaguard Select
®