SDMO PRO 3000 E Instruction And Maintenance Manual

Hide thumbs Also See for PRO 3000 E:

Instruction and maintenance manual (214 pages)

page of 18

/ 18
Bookmarks

Quick Links

Download this manual

Manuel d'utilisation et d'entretien

(Notice originale)

Instruction and maintenance manual

(Translation of the original note)

Manual de utilización y mantenimiento

(Traducción de la información original)

Benutzer- und Wartungshandbuch

(Übersetzung der Original-Anleitung)

Gebruiks- en onderhoudshandleiding

(Vertaling van de oorspronkelijke handleiding)

Vedligeholdelses- og brugsvejledning

(Oversættelse af den originale brugervejledning)

Instruksjoner og sikkerhetsregler

(Oversettelse av de originale instruksjonene)

Bruks- och underhållsanvisning

(Översättning av originalinstruktionerna)

Käyttö- ja huolto-opas

(Alkuperäisen käyttöohjeen käännös)

Kasutus-ja hooldusjuhend

(Originaaljuhendi tõlge)

Naudojimo ir priežiūros vadovas

INVERTER

(Versta iš originalo)

Lietošanas un apkopes rokasgrāmata

(Oriģinālās instrukcijas tulkojums)

PRO 3000 E

‫ﺩﻟﻴﻞ ﺍﻻﺳﺘﺨﺪﺍﻡ ﻭﺍﻟﺼﻴﺎﻧﺔ‬

(‫)ﺗﺮﺟﻤﺔ ﺍﻟﺪﻟﻴﻞ ﺍﻷﺻﻠﻲ‬

PrIndus C5

33522196101_3_1

05/2021

Need help?

Do you have a question about the PRO 3000 E and is the answer not in the manual?

Questions and answers

Summary of Contents for SDMO PRO 3000 E

Page 1 (Översättning av originalinstruktionerna) Käyttö- ja huolto-opas (Alkuperäisen käyttöohjeen käännös) Kasutus-ja hooldusjuhend (Originaaljuhendi tõlge) Naudojimo ir priežiūros vadovas INVERTER (Versta iš originalo) Lietošanas un apkopes rokasgrāmata (Oriģinālās instrukcijas tulkojums) PRO 3000 E ‫ﺩﻟﻴﻞ ﺍﻻﺳﺘﺨﺪﺍﻡ ﻭﺍﻟﺼﻴﺎﻧﺔ‬ (‫)ﺗﺮﺟﻤﺔ ﺍﻟﺪﻟﻴﻞ ﺍﻷﺻﻠﻲ‬ PrIndus C5 33522196101_3_1 05/2021...
Page 4 FRANCE : 0.806.800.107 (Prix appel)
Page 5 CONTENTS Section 1. Preface Section 6. Transporting and storing the generating set Section 2. Instructions and safety regulations (personal protection) Section 7. Repairing minor faults Section 3. Getting started with the generating set Section 8. Technical specifications Section 4. Using the generator set Section 9.
Page 6 Risks relating to exhaust gases DANGER RISK OF POISONING DANGER OF DEATH (if appropriate) The carbon monoxide present in the exhaust gas may lead to death by inhalation if the concentration levels in the atmosphere are too high. Always use the unit in a well ventilated area where the gases cannot accumulate. For safety reasons and for correct operation of the unit, correct ventilation is essential (risk of poisoning, engine overheating and accidents involving, or damage to, the surrounding equipment and property).
Page 7 2.7.4 Connection and choice of cables For all connections, use flexible, strong rubber-sheathed cables which comply with standard IEC 60245-4 or equivalent cables, and ensure that these are kept in perfect condition. Only use one item of class I electrical equipment per socket and connect up equipment using a cable equipped with a PE protective conductor (green/yellow);...
Page 8 Section 3. Getting started with the generating set Key to illustrations The cover illustrations can be used to identify the various components of the unit. The procedures in the manual refer to these illustrations using letters and numbers as identifiers: "A1" refers to the number 1 on figure A. Earth terminal Fuel tap Oil drain screw seal...
Page 9 Checking the engine oil level and topping up Always check the oil level before starting the unit. Place the unit on a flat, level surface. If the unit has been used, leave to cool for at least 30 minutes. Using a screwdriver, remove the screw (A9-E1) and the inspection flap (A10-E2). Remove the oil filler cap (A11-B1) and visually check the oil level: the oil level (B2) should reach the filler neck.
Page 10 Switching the generating set off Shut down and disconnect the equipment used from the electrical sockets (A20) or the battery from the 12V socket (A21), taking care to close the unit's socket cover. Put the economic idle speed (A15) in the (Hare) position.
Page 11 5.3.3 Clean or replace the air filter IMPORTANT Risk of fire or explosion: for a foam element, only use soapy water and clean engine oil during this operation. Remove the nuts (A4) and the enclosure (A3) to access the air filter (A25-D2). Unlock the attachments of the air filter cover (D1) and remove the air filter cover (A2).
Page 12 Storage conditions Drain the fuel and change the engine oil : Start the unit and allow it to operate until it runs out of fuel. Set the switch (A7) to Clean the screen filter (A14-C1). With the engine still warm, change the engine oil. To access the fuel drain screw, undo the screw (E1) and remove the spark plug access cover (E2).
Page 13 Section 7. Repairing minor faults The unit… Check that: Solutions to be applied: The equipment to be used has not Disconnect the equipment then try to start Does not start been connected prior to starting. the unit again. The switch is at Set the switch to The battery is correctly connected and Install the battery;...
Page 14 Serial numbers will be required when requesting troubleshooting advice or spare parts. To keep them safe, note down the serial number of the generating set below. Generating set serial number:……../………….. - ……..……..….…. - ……… Specifications Model INVERTER PRO 3000 E PrIndus C5 Maximum power 3000W Rated output 2800W...
Page 15 (less than once a month), use new fuel with each use or add a stabilizing additive to the fuel tank. EC Declaration of conformity We, SDMO Industries - 270 rue de Kerervern, 29490 GUIPAVAS/CS 40047, 29801 BREST CEDEX 9 – France, hereby declare under our sole responsibility that the following electrical generating sets:...
Page 16 This declaration of conformity is issued under the sole responsibility of the manufacturer. Object(s) of the declaration: Generating set TYPE : INVERTER PRO 3000 E PrIndus C5 SERIAL NUMBER : The object of the declaration described above is in conformity with the relevant statutory requirements applicable to the product: UK Legislation: S.I.
Page 17 SDMO Industries; normal wear and tear of the unit or of one of its components; damage due to negligence, failure to monitor, service or clean the unit;...
Page 18 SDMO Industries is liable for any conformity issues with your unit under the conditions set out in article L. 211-4 and following of the Consumer Code and for hidden defects in the sold item under the conditions set out in articles 1641 and following of the civil code.

This manual is also suitable for:

Prindus c5