Replacement Parts; Important Safety Instructions; Installation - emaux SPV Series User Manual

15. REPLACEMENT PARTS

1
2
3
4 8 9 10 11 12
5
7 6
Key No. Part No.
1 01021143 Nut for lid
2 01041057 Transparent Lid
3 02010253 O-Ring for Lid
4 01112080 Basket
5 89023801 1.5" Union
6 01021144 Pump Body
7 89021307 Drain Plug with O-ring
8
02010245 O-Ring for Diffuser
9 01112081 Diffuser
10
89020719 Screw for impeller with O-Ring
11 01311058 Impeller For SPV150 & EPV150
12 04015065 3/4 Mechanical seal (EPH/EPV/SPH/SPV)
13 02010246 O-Ring for Flange
14 01021145 Flange
15 M8 x 35 Screw with Washer for Motor
89020720
16 03011075 M8 x 30 Screw
17 SPV150 TYC-71L Motor
04020140
18 01112082 Base
18
02010211 Arch Cushion for Base
19 01031027 Fan
20 01321032 Fan Cover
21 Programmable Controller for SPV150
89023901
22 01041061 Transparent Lid for Programmable Controller
P19 REPLACEMENT PARTS
22
21
15
13 14
16 17 19 20
18
Description QTY
1
1
1
1
2
1
2
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1

1. IMPORTANT SAFETY INSTRUCTIONS

The user guide you are holding includes essential information on the safety measures to be implemented for
installation and start-up. Therefore, the installer as well as the user must read the instructions before beginning
installation and start-up. Keep this manual for future reference.
The pump should be installed according to your local electrical installation ordinances and regulations. Only
qualified, licensed personnel should install the pump and the wiring.
This appliance cannot be used by persons (including children) with reduced physical, sensory or mental
capabilities or lack of experience and knowledge unless they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with
the appliance.
This symbol on the product, or in its packaging, indicates that this product
may not be treated as household waste. Instead, it should be taken to the
appropriate waste collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly,
you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by the inappropriate
waste handling of this product. For more detailed information about the
recycling of this product, please contact your local council, your household
waste disposal service, or the shop where you purchased the product.

2. INSTALLATION

1. Install the pump as close to the pool as possible, preferably in a dry, well ventilated area away from direct sun
light. Protect the pump from excessive moisture.
2. Place the pump as close to the water source as possible, so that the suction pipe is short, straight and direct
to reduce the friction loss. Don't install the pump at more than 10ft (3 meters) of geometrical height from
water level.
3. Before installing the pump, make sure that the surface is solid, elevated, rigid and vibration free.
4. Secure the pump to the base with screws or bolts to limit the vibration and the stress on the pipe or the joints.
5. Leave enough space for gate valves in suction and discharge piping, if required.
6. Connect the suction and discharge pipe to the outlet and inlet of the swimming pool.
7. Make sure that floor drainage is adequate to prevent flooding.
8. This pump must be equipped with an isolating
transformer or through a residual current device
(RCD) having a rated residual operating current not
exceeding 30 mA.
9. Make sure that the pump and piping are accessible
for servicing.
Note: The pump suction and discharge connections are
mounded in thread stops, DO NOT try to screw the
pipe beyond these stops.
Correct disposal of this product
IMPORTANT SAFETY INSTRUCTIONS P4