Table of Contents
Advertisement
Quick Links
903545 - 08-31-01.qxd
Instruction
manual
To learn more about Porter-Cable
visit our website at:
http://www.porter-cable.com
Copyright © 2001 Porter-Cable Corporation
2/12/02
11:46 AM
Page 1
Lock Mortiser and
Lock Face Templet
MODEL 517 Lock Face Templet
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No. _______________________________________
ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 31
MODEL
513 Mortiser
IMPORTANT
Part No. 903545 (018)
Advertisement
Table of Contents
Related Manuals for Porter-Cable 513 Mortiser
Summary of Contents for Porter-Cable 513 Mortiser
- Page 1 MODEL 513 Mortiser MODEL 517 Lock Face Templet IMPORTANT Please make certain that the person who is To learn more about Porter-Cable to use this equipment carefully reads and visit our website at: understands these instructions before http://www.porter-cable.com starting operations.
-
Page 2: General Safety Rules
903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 2 GENERAL SAFETY RULES WARNING: READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm. - Page 3 903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 3 influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
- Page 4 WARNING: There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used for any application other than for which it was designed. If you have any questions relative to its application DO NOT use the tool until you have written Porter-Cable and we have advised you.
-
Page 5: Replacement Parts
When servicing use only identical replacement parts. MOTOR Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage within plus or minus 5 percent of that shown on the specification plate on the tool. Several models, however, are designed for A.C. -
Page 6: Standard Equipment
903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 6 LOCK MORTISER ASSEMBLY STANDARD EQUIPMENT With the mortiser, the four sections of the height rod (A), and two bits (B) are furnished. See Fig. 1. Fig. 1 ASSEMBLY OF BASE UNIT The unit is shipped with the crank handle disassembled. Place crank handle (D) to crank shaft (A) (See Fig. -
Page 7: Operation
DO NOT INCLUDE THE LOCK FACE. Select a cutter equal to, or slightly larger than this width. Example: 1) Overall width of lock box – " – Use PORTER-CABLE #43704 1" diameter bit. 2) Overall width of lock box –... - Page 8 903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 8 Fig. 6 SETTING MORTISER FOR LENGTH OF CUT CAUTION: Disconnect tool from power source. See Fig. 6 to set mortiser for length of cut. Loosen crank pin nut (T) and turn adjusting knob (U) until the correct graduation mark on the slide lines up with the line on crank pin indicating washer.
- Page 9 903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 9 MAKING TRIAL CUT After the mortiser (see Fig. 8) has been set up according to the preceding instructions, it is strongly recommended that a trial cut be made in the following manner to insure fit of lock box. Clamp a length of 2"...
- Page 10 903545 - 08-31-01.qxd 2/12/02 11:46 AM Page 10 NOTE: Be sure the length of the mortise has not removed stock required for the two screws that retain the lock box to the door. MORTISING A DOOR After trial cut has been made resulting in a satisfactory fit for the lock box, the door should be mortised in the following manner.
-
Page 11: Required Equipment
903545 - 08-31-01.qxd 2/12/02 11:47 AM Page 11 Fig. 11A Fig. 11 MODEL 517 LOCK FACE TEMPLET REQUIRED EQUIPMENT Equipment required for use with Router and Lock Face Templet. 42024 Templet Guide 42237 Locknut 43440 " Diameter Straight Bit SETTING UP TEMPLET Loosen locking screw (A), Fig. -
Page 12: Making The Cut
903545 - 08-31-01.qxd 2/12/02 11:47 AM Page 12 LOCATING TEMPLET ON DOOR Draw a line across the door edge at the center of the mortise cut for the lock. Draw line (F), Fig. 12, on the templet side guides (C), midway between bars (B) and (E). -
Page 13: Maintenance
FACTORY SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest authorized Porter-Cable Service Station to be thoroughly cleaned and inspected. Have worn parts replaced and lubricate with fresh lubricant. Have new brushes installed, and test the tool for performance. -
Page 14: Service And Repairs
PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. - Page 15 Pour obtenir des pièces et accessoires pour les produits Porter-Cable • Delta, s’adresser à tout distributeur Porter- Cable • Delta, centre de service agréé ou centre de service d’usine Porter-Cable • Delta. Si vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable •...
Need help?
Do you have a question about the 513 Mortiser and is the answer not in the manual?
Questions and answers