Advertisement
Table of Contents
- 1 Dear Customer
- 2 Environmental Protection
- 3 Description of Symbols
- 4 Specifications
- 5 General Safety Instructions
- 6 Know Your Product
- 7 Installing and Removing Collets
- 8 Installing and Removing Router Bits
- 9 Adjusting the Mitre Gauge
- 10 Turning on and off
- 11 Mounting to a Workbench
- 12 Operation
- 13 Maintenance
- Download this manual
Advertisement
Table of Contents
Summary of Contents for Global Machinery Company 1050W
- Page 1 I N S T R U C T I O N M A N UA L 1050W Powered Router Table • Melbourne • Perth • Auckland • Hong Kong • Shanghai • Taipei • New York • Verona • London • Paris...
- Page 2 Contents...
-
Page 3: Dear Customer
Wear breathing protection. Double insulated for additional protection. Conforms to relevant standards for electromagnetic compatibility. Specifications Nominal voltage: 230–240Vac ~ 50Hz Power: 1050W No load speed: 8000-30000 RPM Collet capacity: 1/2” (12.7mm) and 1/4” (6.35mm) Cutting depth: 36mm Spindle lock: Insulation:... -
Page 4: General Safety Instructions
General safety instructions The tool must be used only for its prescribed purpose. Any use other than those mentioned in this Manual will be considered a case of misuse. The user and not the manufacturer shall be liable for any damage or injury resulting from such cases of misuse. - Page 5 Remove the plug from the socket before carrying out any adjustment, servicing or maintenance • Use your powered router table on a level and flat stable surface or firmly clamp or bolt your powered router table to a workbench. Place the powered router table at around hip height for maximum convenience and safety •...
- Page 6 1/2” & 1/4” collets • Mitre gauge We recommend that you purchase all additional accessories such as router bits from the store where you bought the tool. Use good quality accessories with a well-known brand name. Store personnel can help and advise.
-
Page 7: Know Your Product
Know your product 1. Table 2. Rear fence 3. Infeed fence 4. Outfeed fence 5. Fence locking knobs 6. Guide block locking knobs 7. Dust extraction hood 8. Dust extraction port 9. On/Off switch 10. Mitre gauge 11. Mitre gauge locking knob 12. -
Page 8: Installing And Removing Collets
1/4" (6.35mm) and 1/2" (12.7mm). The 1/2" (12.7mm) collet is fitted to the product upon purchase. 2. Depending on the size of the router bit the collet may need to be changed to allow use of larger or smaller diameter router bits. -
Page 9: Installing And Removing Router Bits
Fit the two securing screws and tighten firmly. Caution. Do not fully tighten the collet nut with the wrench unless there is a router bit in place or you may damage the collet. Installing and removing router bits Warning. - Page 10 3. To determine the depth of cut use a ruler to measure the distance between the base of the table and the tip of the router bit. 4. Align the height adjustment lock and rotate the lock in a clockwise direction to lock.
- Page 11 Adjusting the fence for trimming 1. When trimming timber the material coming out on the left hand side (outfeed) (4) of the cutter will be thinner than the material being fed through on the right hand side (infeed) (3). 2. The left hand guide block will need to be adjusted to compensate for the thinner material.
-
Page 12: Adjusting The Mitre Gauge
(8). Mounting to a workbench 1. The powered router table has a hole in each corner of the plastic foot allowing it to be bolted to a workbench for greater stability. 2. Fit an 8mm bolt (not supplied) through each corner of the plastic foot of the powered router table to secure it to the workbench. -
Page 13: Operation
Practice first on a scrap piece of material to gauge the correct feed rate and cut dimensions. 13. Turn the powered router table off by pushing on the red cover. Maintenance Warning. - Page 14 Carefully read the entire Instruction Manual Before returning this product for a Warranty Claim or any other reason Please Call 1300 880 001 (Australia) or 0800 445 721 (New Zealand) When you make your call, please have the following information at hand: •...
Need help?
Do you have a question about the 1050W and is the answer not in the manual?
Questions and answers