Page 1
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V. ...
TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V. ...
Ultra HD signals, you can switch off For more specification details of this product, see Ultra HD for this HDMI connection. www.philips.com/TVsupport • The setting Optimal* allows maximum up to Ultra HD (50Hz or 60Hz) RGB 4:4:4 or YCbCr 4:4:4/4:2:2/4:2:0 Display Resolution signals.
Page 4
• Satellite aerial input : 75 ohm F-type Wi-Fi 802.11n(built-in) • Input frequency range : 950 to 2150MHz Supported USB file systems FAT, NTFS • Input level range : 25 to 65 dBm • DVB-S/S2 QPSK, symbol rate 2 to 45M symbols, SCPC Playback formats and MCPC ...
Refer to the diversity tables for the correct values. two pins of the Mains/AC Power plug. • The correct component values are listed on the Philips • Check the cabinet for defects, to prevent touching of any Spare Parts Web Portal.
Page 6
• Mix of lead-free soldering tin/parts with leaded soldering tin/parts is possible but PHILIPS recommends strongly to avoid mixed regimes. If this cannot be avoided, carefully clear the solder-joint from old tin and re-solder with new tin.
Page 7
originating from the USA and used e.g. in • Always respect voltages. While some may not be dangerous in themselves, they can cause unexpected LATAM and AP-NTSC countries reactions that are best avoided. Before reaching into a B-TXT Blue TeleteXT powered TV set, it is best to test the high voltage Centre channel (audio) insulation.
Page 8
G-TXT Green TeleteXT distance is 6.5 MHz. L' is Band I, L is all H_sync to the module bands except for Band I High Definition LG.Philips LCD (supplier) Hard Disk Drive Loudspeaker HDCP High-bandwidth Digital Content Protection: LVDS Low Voltage Differential Signalling A “key”...
Page 9
Serial Peripheral Interface bus; a 4-wire module, implementing the CA system for a synchronous serial data link standard host (e.g. a TV-set) S/PDIF Sony Philips Digital InterFace Power On Reset, signal to reset the uP SRAM Static RAM PSDL Power Supply for Direct view LED...
Page 10
Thin Film Transistor toward external amplifier Total Harmonic Distortion Vestigial Side Band; modulation method TMDS Transmission Minimized Differential WYSIWYR What You See Is What You Record: record Signalling selection that follows main picture and Transport Stream sound TeleteXT WXGA 1280 ×...
3.2 Assembly/Panel Removal 3.2.1 IR board Control Unit 1. Unplug the connector from the SSB. Caution: be careful, as these are very fragile connectors! 2. Remove fixation screws [1] and connector [2] from the IR board control unit. 3. Remove the IR lens, IR board from the DECO_REAR_COVER. When defective, replace the whole unit.
Page 16
3.2.3 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1. Remove all fixation screws [2] and [3] that secure the Back cover assy. 2. Unplug the connector [2] that marked by red box below from SSB. 3.
Page 17
2 2 3.2.5 Small Signal Board (SSB) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the SSB. 1. Release the clips from the LVDS connector that connect with the SSB[1]. Caution: be careful, as these are very fragile connectors! 2.
Page 18
3.2.6 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 20
– (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 21
Remark: 1. Press following Key Combination to reset the “Op Hour”: “Menu/Home” + “101011” on the remote control transmitter. 2. Under main menu “NVM editor”, select “Service Data”, you can use the UP/DOWN keys to view and change the set Type number, the set Production Number or the 18AC of a part.(The NVM-editor still has the same function as before, alpha-numeric entry.) 4.3 Factory mode: Purpose...
Page 22
How to Exit the Factory mode Select EXIT_FACTORY from the menu and press the “OK” button. Note: When the TV is switched “off” by a power interrupt, or normal switch to “stand-by” while in the factory mode, the TV will show up in “normal operation mode”...
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading 5.1.1. The following update is for .pkg file. 1. Rename the file to “upgrade_loader.pkg”. 2. Prepare a USB memory (File format: FLAT, Size: 1G~8G). 3. Copy the software to USB flash disk (root directory). 4.
Page 24
Step 2: F/W Upgrade 1. Press [Quick settings], then Choose [Update Software] in the Settings menu 2. Choose [Local Updates], then press OK. 3. Select the file that you downloaded and press OK 4. Choose [Update], then choose [Start] on following step ...
Page 25
5. Upgrade in progress Step 3: Check the SW version After burning software, TV will restart Press “123654”, enter Customer Service Mode to check if the software version is correct. Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! ...
Page 26
5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set. In principle a unique error code is available for every: • Activated (SW) protection. • Failing I2C device. • General I2C error. The last five errors, stored in the NVM, are shown in the Service menu’s. This is called the error buffer. The error code buffer contains all errors detected since the last time the buffer was erased.
Page 27
5.2.4 How to Clear the Error Buffer The error code buffer is cleared in the following cases: • By using the CLEAR command in the SAM menu • By using the CLEAR command in the Factory mode: • By using the following key sequence on the remote control transmitter: “062599” directly followed by the OK button. •...
Page 28
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Set Option Code” in below tab. After resetting the Display Code, restart the set immediately. Set Option CTN_ALT BOM# Panel Type Code 43PUS6503/12 TPT430U3-QVN03.U S0B0H 43PUS6523/12 TPT430U3-QVN03.U S0B0W 43PUS6703/12 TPT430U3-QVN03.U S0B0K 43PUS6753/12 TPT430U3-QVN03.U S0B0K...
Trouble shooting 2016年12月10日 2016/4/8 Picture-related Intermittent Ask Photo Picture ? problem ? Menu Smarkt Signal SW latest ? Backlight? issue function? issue SSB+LVDS+Panel Update SW LED working ? PSU/SSB Problem solved ? Sound ? PSU+ Panel Finish SW+SSB...
Page 30
Trouble shooting 2016年12月10日 2016/4/8 Audio/Sound- related Intermittent Sound ? problem ? Setting SW latest ? Mute ? issue issue Update SW Extra device Check extra connect? device Problem solved ? Factory setting Finish Sound back ? Setting issue SSB+SPK...
Page 31
6.Slow response to user interaction 7.Switches ON by itself 8.Switches Off by itself 9.Stuck in standby mode / unable to start up 10.Stuck on PHILIPS / ANDROID logo 11.CAM not recognized by TV 12.CAM authentication issue 13.Misc CAM issue 14.IP-EPG issues 15.BC-EPG issues...
Page 33
7.2 Power Supply Power architecture of this platform. AUDIO LVDS 12V Platform power Display power CN8601 DIM CN8603 for 715G9324P ON/OFF Platform PS_ON 12V MT5802 12V_A CN701 AC‐input + PFC Main filter AC IN 7.3 Power tree ...
Page 34
7.4 Power layout SSB C789 +12V PANEL L701 +1.5V DDR L704 +3.3V SB L702 +5V_STB L803 +5V Power SSB Top View ...
9.10 J 715G8555 Keyboard control panel (For 6803/6703/6753 Series) 9-10-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY1 AMBI_SPI_CLK...
Need help?
Do you have a question about the 43PUS6503 and is the answer not in the manual?
Questions and answers