Page 2
This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright. No information contained herein may be copied, translated, transcribed or duplicated for any commercial purposes or disclosed to the third party in any form without the prior written consent of SAMSUNG Electronics Co., Ltd.
Ubigate iBG1003 Quick Start Guide GENERAL USER INFORMATION Radio Frequency Interference The Ubigate iBG1003 equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to FCC Part 15 Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
GENERAL USER INFORMATION FCC Requirements The Ubigate iBG1003 equipment complies with FCC Part 68 Rules and requirements adopted by Administrative Council for Terminal Attachment (ACTA). FCC Part 68 The FCC Part 68 label is located on the bottom of the chassis.
Ubigate iBG1003 Quick Start Guide Telephone Connection Requirement A plug and jack is used to connect this equipment to the premises wiring and telephone network must comply with the FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product which is designed to connect to a compatible Standard Modular jack.
Incidence of Harm The telephone company will notify you in advance about the temporary discontinuation of service, if the Ubigate iBG1003 equipment is causing harm to the telephone network. In case advance notification is not feasible, the telephone company will notify the customer as soon as possible and you will also be advised about your right to file a complaint with the FCC, if it is necessary.
Field Repairs Only technicians certified on the Ubigate iBG1003 are authorized by SAMSUNG ELECTRONICS, CO., LTD. to perform system repairs. Certified technicians may replace modular parts of a system to repair or diagnose trouble.
Publishers (ASCAP) or other similar organizations if copyright music is transmitted through the Music on Hold feature. SAMSUNG ELECTRONICS, CO., LTD. hereby disclaims any liability arising out of failure to obtain such a license. Direct Inward System Access (DISA) Warning The lines used for the DISA feature must have the disconnected Supervision option provided by the telephone company.
Every wire for communication should be larger than 26 AWG. Double pole/neutral fusing. Underwriters Laboratories The Ubigate iBG1003 system has been tested to comply with Safety Standards in the United States and Canada. This system is listed with Underwriters Laboratories. The cUL Mark is separately shown on the label.
Ubigate iBG1003 Quick Start Guide Installation Safety Guidelines and Warnings Safety Recommendations The Safety Warnings that appear in this document (such as the one below) indicate a procedure that can harm you if not done correctly. Electric hazard exists. Verify the power is turned off.
Page 12
GENERAL USER INFORMATION Cover Panels Do not operate the Ubigate iBG1003 with missing blank faceplates and cover panels. These covers prevent exposure to hazardous voltages and currents inside the chassis. They are important to maintaining proper air flow through the chassis. They also prevent electromagnetic interference (EMI) that might disrupt other equipment.
Page 13
Ubigate iBG1003 Quick Start Guide Use care when installing or uninstalling modules or interface cards. Tighten the captive installation screws to ensure a proper connection when inserting modules or interface cards. When removing or installing a component, always place it component-side up on an antistatic surface, in an antistatic card rack.
Ubigate iBG1003 Quick Start Guide CHAPTER 1. Verifying the Ubigate iBG1003 Inspecting the Ubigate iBG1003 Remove all the packing material and boxes from the shipping crate very carefully. The router is maximally protected inside the shipping crate. Do not unpack it until you are ready to begin installation.
Page 20
Ubigate iBG1003 Quick Start Guide Ubigate iBG1003 Manual CD If any part is missing or damaged, contact Samsung Technical Support: http://www.samsung.com/global/business/telecomm/footer/Footer_Cont actUs.html Save the shipping crate cover, pallet, and packing materials in case you need to move or ship the router at a later time.
Additional information is also provided about external cables, wiring, and connection points. Ubigate iBG1003 Front Side The front side of the Ubigate iBG1003 has LEDs to indicate the iBG1003 routers performance and operation status, as shown in figure below.
Page 22
CHAPTER 1. Verifying the Ubigate iBG1003 (Continued) Indication & Description Color Solid green IOM (Internal Option Module) card present and operational. Solid red IOM card present but not operational. IOM card not present. Solid green Fan is operating properly. Solid red Fan present but malfunctioning.
Ubigate iBG1003 Quick Start Guide Ubigate iBG1003 Rear Side Ubigate iBG1003 rear side has several interface ports and slots as shown in figure below. Power connector, power switch, and ground stud are also located in the rear side. Ground Power...
Desktop Installation For installing chassis, you must secure unrestricted airflow for chassis cooling. Place the Ubigate iBG1003 router on a clean flat stable surface with at least 18 by 19 inch of clear space to allow sufficient room for interface cabling, power cord clearance, and adequate ventilation.
CHAPTER 2. Ubigate iBG1003 Installation Rack Mount Installation Attaching Rack-Mount Brackets Before installing the router on a rack, you need to attach brackets to the router. The brackets can be ordered separately. Attach the mounting brackets to the router as shown in figure below, using the 4 of M4xL8 screws included.
Page 28
CHAPTER 2. Ubigate iBG1003 Installation Grounding the Ubigate iBG1003 You must connect the chassis to a reliable earth ground as shown in below figure. Verify the following: The grounding cable is correctly installed It does not touch or block access to router components.
Page 30
CHAPTER 3. Connecting the Ubigate iBG1003 To connect the console cable: Plug the RJ-45 end of the cable into the console port on the Ubigate iBG1003 as shown in below figure. Plug the other end of the cable which has the adapter with the female DB-9 connector to the communication port on the workstation or terminal.
Ubigate iBG1003 Quick Start Guide Ethernet Port The Ubigate iBG1003 has two 10/100 Mbps Ethernet ports. Use a Category 5 (minimum) Ethernet cable with RJ-45 connectors to connect to the network via an Ethernet port. Plug one end of the Ethernet cable into the appropriate Ethernet port on the target router.
CHAPTER 3. Connecting the Ubigate iBG1003 Powering Up the Ubigate iBG1003 The Ubigate iBG1003 has a 72 Watts AC power supply module. Connecting AC Power To connect the AC power cord to the router: Connect the AC power connector to the power supply.
To apply power to the Ubigate iBG1003: Ensure that the Ubigate iBG1003 is connected to a power source. Switch the rocker switch on the Ubigate iBG1003 rear side to the on position ( | ) Then, the fan starts, the LEDs start to blink in different colors, and the Ubigate iBG1003 performs a self test.
Once done, the login prompt is displayed on the console screen. To login, enter default login ID and password for the administrator. The default login ID for the administrator is ‘samsung’. The user can change the login ID to suit his/her needs after the initial login.
Changing the Administrator Login ID This section describes how to change the administrator login ID. The default login ID for the administrator is ‘samsung’. For security reasons, it is strongly recommended to change the login ID as soon as possible.
Execute the ‘password’ command. Router# password The system prompts for the current user name. Type ‘samsung’, and press Enter. The system prompts to enter the old password. Type ‘samsung’, and press Enter. The system prompts to enter a new password.
Ubigate iBG1003 Quick Start Guide Setting the time using Time command To set the time, enter in the format of ‘HH MM SS’ (Hour Minute Second). For example, to set the time to 18:14:30, enter ‘time 18 14 30’ as shown below and press ENTER.
Ubigate iBG1003 Quick Start Guide Removing Users The administrator can remove the configured user name from the system. To remove a user, follow the steps below: Enter the configuration mode by executing the following command. Router# configure term Type ‘no user’, followed by the user name and press Enter.
Page 45
Ubigate iBG1003 Quick Start Guide Initializing Configuration To reset to factory default configuration, you need to clear the contents of the system. cfg file. In order to do this, execute the ‘clear cfg_file’ command. Then, reboot the system by executing the ‘reboot’ command.