Advertisement
Quick Links
Mounting Hanger for Low Ceilings
Assembly and Installation Instructions
LV-CL07
Be sure to consult with a qualified installation specialist.
This mounting hanger is specifically for use with our projectors listed on above. Do not use for any
other equipment or purposes. Be especially careful that children do not hang from it. Perform proper
assembly and installation by following these instructions. Be sure to follow all precautions.
When hanging a projector from the ceiling using this mounting hanger, the ceiling must have
adequate strength to support both the projector and the mounting hanger. Before
Precautions
installation, check the combined weight of the projector and hanger, as well as the strength
of the ceiling based on that weight. If the strength is insufficient, provide adequate
reinforcement before proceeding.
●Always mount on a level ceiling. Never install on an inclined ceiling.
●During installation, take appropriate measures to prevent lateral swaying due to
earthquakes or vibration (using wires, etc.).
The total weight of the mounting hanger itself is
(A)Screw...8 (B)Screw...4 (C)Screw...8 Fastening This Manual
Included
Accessories
Assembly and Installation
1. Turn the projector over, and mount the projector bracket using the four (A) screws.
2. Determine the projection distance, and then determine the mounting position of the ceiling bracket.
3. Mount the ceiling bracket to the ceiling. See the figures for bracket mounting dimensions.
4. Hang the projector by aligning the groove in the projector bracket (attached to the projector) with the ceiling
bracket already fastened in place.
Note) Be careful not to drop the projector. The projector is not yet securely mounted.
5. Mount the projector bracket and two fastening plates using the four (B) screws.
6. Tentatively fasten the four (A) screws to the ceiling bracket. (Tighten after determining the projection position.)
7. Mount the securing band to the projector bracket using the eight (C) screws.
Adjusting the Projection Position
1. Inclination angle adjustment :
After aligning the position with the screen, securely fasten the (A) screws in four locations.
2. Vertical angle adjustment :
Loosen the (D) screws, align the position with the screen, and then securely fasten the (D) screws.
3. Left/right angle adjustment :
Loosen the (E) screws, align the position with the screen, and then securely fasten the (E) screws.
Compatible projector models
LV-7545
4.5
plate...2
See Fig. 1
See Figs. 2, 3
Fig. 1 ... Assembley
Projector
(C)screw
Phillips head machine screw
with integrated spring washer
and flat washer M4×10 (×8)
kg.
...1
(B)screw
Detailed view of ceiling bracket and
projector bracket
Fig. 2 ... Adjustment (front view)
(A)screw
(4 locations)
Inclination angle
adjustment
［Inclination angle]
319
345.4
(A)screw
Phillips head hex bolt
with integrated spring
washer and flat washer
M6×12 (×4)
※
Projector bracket
(×1)
(B)screw
Phillips head machine screw
with integrated spring washer
and flat washer M3×8 (×4)
(A)screw
Phillips head hex bolt with
integrated spring washer
and flat washer M6×12 (×4)
Fastening plate (×2)
(A)screw
Fastening
plate
Unit:mm
Fig. 3 ... Adjustment (side view)
(D)screw
(4 locations)
Vertical angle
adjustment
［Vertical angle]
142.1
155.2
projection direction
Attach the bracket
Ceiling bracket
so that the arrow is
(×1)
pointing in the
projection direction
(toward the front of
the projector).
Unit:mm
[Left/right angle]
10
120
4-φ10
200
230
Ceiling bracket mounting dimensions
Unit:mm
(E)screw (4 locations)
Left/right angle adjustment
208
470.2
Advertisement
