Related Manuals for Spaceman 6450
Summary of Contents for Spaceman 6450
- Page 1 SPACEMAN FROZEN BEVERAGE MACHINE TRAINING *use this training guide for Spaceman USA models: 6450, 6455H, 6490H, 6650, 6690H, 6695H, 6795H Spaceman USA Frozen Beverage Training rev042219...
- Page 2 All Spaceman USA Frozen Beverage machines are capable to freeze alcoholic beverages. Most Spaceman beverage machines (except for 6450 and 6650) include refrigerated hoppers and a standby mode. Product is poured into the hopper (product should be below 41°F) where it is kept until flowing into the freezing cylinder via the air tube.
-
Page 3: Routine Maintenance Operations
Tune-Up Kit is available with properly clean the machine. all wearable parts (O-rings, gaskets, etc.) except scraper blades ** Based on cleanliness of location and proximity to powder-based machines Spaceman USA Frozen Beverage Training Tune-Up Kit rev042219... - Page 4 Doing so may cause damage to the stainless Cleaning and sanitizing steel material. schedules are governed by state ONLY use Spaceman-USA-included cleaning brushes and lubrication. or local regulatory agencies and MUST be followed accordingly. NEVER use metal objects to clean or operate the machine.
- Page 5 To expedite draining, turn off NEVER use warm water machine minutes prior to when rinsing the machine soften product. To expedite to prevent damage. process, keep a bucket nearby to temporarily store removed parts. Spaceman USA Frozen Beverage Training rev042219...
- Page 6 DRAIN PRODUCT Place a bucket or other Turn power switch Remove hopper lid and Turn power switch to container below draw to OFF Position agitator (if present) WASH valve to capture product as it drains Spaceman USA Frozen Beverage Training rev042219...
- Page 7 DRAIN PRODUCT Move draw handle to OPEN Move draw handle to Turn power switch Remove product and position (RIGHT) until all CLOSED position (LEFT) to OFF dispose or product runs out refrigerate it Spaceman USA Frozen Beverage Training rev042219...
- Page 8 Fill hopper with a minimum of 2 Use the small brush gallons of COOL water kit to clean inside the feed tube at the bottom of the hopper Spaceman USA Frozen Beverage Training rev042219...
- Page 9 Turn power switch Repeat steps 9 to Turn power switch drain water and to OFF 14 until water to WASH remaining product; exiting the draw CLOSE when finished valve is clear and free of product Spaceman USA Frozen Beverage Training rev042219...
- Page 10 DISASSEMBLE NOTE CAUTION Prepare dishwashing area ALWAYS separate O- prior to disassembly, and rings and gaskets from use a bucket to temporarily metal parts to prevent store removed parts. damage while washing. Spaceman USA Frozen Beverage Training rev042219...
- Page 11 DO assembly NOT LIFT UP ON Verify the power Remove CURVED SENSOR ARM switch is turned dispensing door to OFF hand-screws (4) Spaceman USA Frozen Beverage Training rev042219...
- Page 12 *some new models will not have blade clips Remove dispensing door gasket using O-ring tool Rotate draw valve until the flat part at the top is perpendicular to the clear face of the dispensing door (use towel if necessary) Spaceman USA Frozen Beverage Training rev042219...
- Page 13 DISASSEMBLY Remove ice buster Remove draw valve, twisting it while removing Remove draw valve O-rings (2) using O-ring tool Unscrew and remove prime plug from dispensing door Spaceman USA Frozen Beverage Training rev042219...
- Page 14 DISASSEMBLY Separate drive shaft gasket from drive shaft Use a towel to remove drive Remove front drip tray shaft at the back of the cylinder and internal drip tray Spaceman USA Frozen Beverage Training rev042219...
- Page 15 Gently clean and wipe down the outside of the machine CAUTION: Never wash parts in a dishwasher. Always hand-wash Spaceman USA Frozen Beverage Training components with nontoxic, food-safe cleaners. rev042219...
- Page 16 O- small brush rings removed from the machine; be sure to wipe gaskets and O-rings to remove excess lubricant Verify all parts are clean and free of all food Spaceman USA Frozen Beverage Training rev042219...
- Page 17 (when inserted correctly, the drive shaft will no longer turn 360°) Spaceman USA Frozen Beverage Training rev042219...
- Page 18 ASSEMBLE Install scraper blade clip(s) onto scraper blade(s) Install beater assemblies Fit scraper blades onto beater Insert assembly into cylinder; turn assembly until it engages the drive shaft key and no longer turns 360° Spaceman USA Frozen Beverage Training rev042219...
- Page 19 Place O-ring on torque Insert torque assembly into assembly, coating with pilot hole in the center of the Spaceman lubricant drive shaft (torque guide first), ensuring that torque guide DOES NOT fall off Spaceman USA Frozen Beverage Training rev042219...
- Page 20 Insert ice buster through the dispensing spout at the bottom of the door and into the slot on the draw valve Spaceman USA Frozen Beverage Training rev042219...
- Page 21 Place dispensing door ice buster in place; turn secure in place with dispensing door gasket on door, coating valve until the hole for valve pin with Spaceman lubricant the draw handle is accessible on front Spaceman USA Frozen Beverage Training rev042219...
- Page 22 With tapered end down, install torque arm up through the flat sensor arm and then down into the torque assembly; torque arm should move freely back and forth; DO NOT LIFT UP ON CURVED SENSOR ARM Spaceman USA Frozen Beverage Training rev042219...
- Page 23 ASSEMBLE Install hopper assembly and drip trays If machine has hopper agitator, Install hopper lid lubricate inside it and install with and drip trays arrow pointing up (internal and front) Spaceman USA Frozen Beverage Training rev042219...
- Page 24 Sanitize machine before using again. machine. Spaceman USA Frozen Beverage Training rev042219...
- Page 25 Pour food-grade sanitizer is in the CLOSED solution into the hopper position (LEFT) Verify assembly is Mix a minimum of 2 gallons complete and machine of food-grade sanitizer in a power is OFF bucket or container Spaceman USA Frozen Beverage Training rev042219...
- Page 26 Allow solution to agitate and distribute sanitizer for 5 to 10 minutes; solution along hopper NEVER leave machine walls and hopper agitator on WASH for more than (if present) 10 minutes Spaceman USA Frozen Beverage Training rev042219...
- Page 27 SANITIZATION ASSEMBLE Place a bucket or container OPEN the draw valve Turn power switch below the draw valve (RIGHT) and drain to OFF solution from the machine Spaceman USA Frozen Beverage Training rev042219...
- Page 28 NOTE low mix. Doing so WILL cause freeze up and damage to your machine. MIX LOW light illuminates when the hopper is low on product mix and automatically turns off when machine is filled. Spaceman USA Frozen Beverage Training rev042219...
- Page 29 (free of tight, and perform sanitizing large chunks) steps (Page 13) Spaceman USA Frozen Beverage Training rev042219...
- Page 30 Once sanitizer has been into the hopper; sanitizer purged from the machine and will start to flow out of the a steady stream of product is draw spout flowing from the spout, CLOSE draw handle (LEFT) Spaceman USA Frozen Beverage Training rev042219...
- Page 31 (counter-clockwise) on the screw and tighten hopper front of the dispensing door completely and allow the cylinder to fill with product to the desired level; cylinder must be at least 75% full to operate Spaceman USA Frozen Beverage Training rev042219...
- Page 32 When the product reaches the desired viscosity, it is ready to dispense If machine doesn’t turn on, turn power switch OFF, wait 30 minutes, and repeat steps 1 to 4. If problem persists, contact service team. Spaceman USA Frozen Beverage Training rev042219...
- Page 33 FROZEN PRODUCT OPERATION DISPENSE PRODUCT OPEN CLOSE OPEN draw handle CLOSE the draw (RIGHT) until the desired handle (LEFT) when amount is dispensed finished dispensing Spaceman USA Frozen Beverage Training rev042219...
- Page 34 Light may be amber color. • Allow 5 to 10 minutes for machine to begin • Light illuminates green when machine freezing again. is in STANDBY mode. Spaceman USA Frozen Beverage Training rev042219...
- Page 35 Make small adjustments each time, and allow at least 10 to 15 minutes between adjustments to evaluate product firmness. Spaceman USA Frozen Beverage Training rev042219...
- Page 36 Switched RIGHT means consistency is correct. Switched It moves UP when draw handle is in LEFT or IN THE MIDDLE means the OPEN position. consistency is not yet correct. Spaceman USA Frozen Beverage Training rev042219...
Need help?
Do you have a question about the 6450 and is the answer not in the manual?
Questions and answers