VENTILATION FAN WITH LIGHT AND HEATER MODEL RAD80L TABLE OF CONTENTS Package Contents Important Instructions Preparation Assembly Instructions Wiring Instructions Operating Instructions Care and Maintenance Troubleshooting Dimensions Product Specifications Warranty READ AND SAVE THESE INSTRUCTIONS Please read and understand this entire manual before attempting to assemble, operate, or install the product.
(customer service number located on last page). • Do not install less than 8 ft. (2.4 m) from the floor. ‧ I nstallation work must be carried out by a qualified person(s) in accordance with all local and safety codes Model: RAD80L...
Dimension (L) Dimension (W) Dimension (H) 14.62 in. 8.50 in. 5.50 in. 14.38 in. 8.25 in. 5.50 in. WARNING Be careful to cut hole exactly. If the hole is too big, the fan grille will not hide it. Model: RAD80L...
Page 5
• Wiring can be run to the planned location. • No wiring or other obstructions can interfere with installation. WARING: • To reduce the risk of fire, do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater. Model: RAD80L...
Secure the suspension brackets to fan body ❶ with the short machine screws f. Remove tap before connecting the duct as shown in Figure 1-2. Hardware Short Machine Screw (M4x12) Qty.4 ∅ Wood Screw( 4x14) Qty.8 Model: RAD80L...
Page 7
Elbow near the body Body Minimum 18 in. 3. Remove the fan junction box cover . Using wire nuts (not supplied), connect house wires to fan wires as shown in the wiring diagram on page 10. Reattach fan junction box cover Model: RAD80L...
Page 8
Plug the Light Connector into the receptacle marked “Light” c. Install the Grille Assembly ❷ into the Fan Body ❶ using the Machine Screw CAUTION: Do not use Wood Screw in place of Machine Screw ∅ Wood screw ( 4x14) Machine screw (M5x14) Model: RAD80L...
Page 9
ASSEMBLY INSTRUCTIONS d. Install a 26W(max.) type GU 24 fluorescent lamp ❸ into Grille Assembly ❷ . e. Install the Light Lens ❹ into Grille Assembly ❷ . Model: RAD80L...
1. Turn on the light switch to turn on the light bulb. 2. Turn on the vent switch to operate the fan mode. 3. Turn on the heat switch to operate the heater mode. Model: RAD80L...
• Allow lamp to cool before replacing. To clean fan, disassemble using the following steps: 1. Remove Light Lens ❹ cover. 2. Remove 26W(max.) type GU24 Fluorescent Lamp ❸ . 3. Remove Machine Screw Hardware Machine Screw (M5x12) Qty.1 Model: RAD80L...
Page 12
Never use solvents, thinner or harsh chemicals when cleaning the fan. Vacuum cleaner 6. Replace Grille Assembly ❷ back onto Fan Body ❹ . Please refer to Completing the Installation. Follow the steps on pages 8-9 to assemble fan back together. Model: RAD80L...
The fan is not able to draw air out of the room without enough airflow to draw in from. 2. Insufficient CFM 2. Be sure the CFM rating on the fan matches the requirements for your room size. Model: RAD80L...
DIMENSIONS 5.50 16.81 1.91 Unit: inch 14.38 PRODUCT SPECIFICATIONS SPECIFICATIONS Model No. RAD80L Airflow @ 0.1 in. WG 80 CFM Noise 1.3 Sones Voltage 120V Hertz 60Hz Power Consumption 1340W Duct Diameter 4 in. Weight 12.1 lbs. TYPE IC INHERENTLY PROTECTED.
Need help?
Do you have a question about the RAD80L and is the answer not in the manual?
Questions and answers
where is the cut off fuse located at ? is it replaceable ?
I need a color coded
I need clarification on the actual colors of wires as they are when hooked up?
The wire colors for the DELTA BREEZ RAD80L when hooked up are:
- Red
- Black
- Blue
- White
- Ground (bare wire)
This answer is automatically generated