FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 7. Safety Devices Setting Model FXDQ20PDVE FXDQ25PDVE FXDQ32PDVE Printed circuit board fuse 250 V, 5 A 250 V, 5 A 250 V, 5 A OFF: 130±5 OFF: 130±5 OFF: 130±5 Fan motor thermal protector °C ON: 83±15 ON: 83±15 ON: 83±15 Drain pump thermal fuse °C Model FXDQ20PDVET FXDQ25PDVET FXDQ32PDVET Printed circuit board fuse 250 V, 5 A 250 V, 5 A 250 V, 5 A OFF: 130±5 OFF: 130±5 OFF: 130±5 Fan motor thermal protector °C ON: 83±15 ON: 83±15 ON: 83±15 Drain pump thermal fuse...
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 13. Installation Manual l l a necessary to take proper measures so that the amount of CONTENTS any leaked refrigerant does not exceed the concentration 1. SAFETY PRECAUTIONS..........1 limit in the event of a leakage. 2.
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 (If the system is charged with refrigerant in its gaseous state, CAUTION due to composition change, the system will not function • Install drain piping according to this installation manual to normally). The indoor unit is designed for R410A use. ensure good drainage, and insulate the piping to prevent See the catalogue for indoor unit models that can be condensation.
Page 40
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 FOR THE FOLLOWING ITEMS, TAKE SPECIAL 2-2 ACCESSORIES CARE DURING CONSTRUCTION AND CHECK Check the following accessories are included with your unit. AFTER INSTALLATION IS FINISHED. Metal Drain Insulation Sealing pad Name clamp (1) hose (2) for fitting a.
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 3. SELECTING INSTALLATION SITE (2) Use suspension bolts for installation. Check whether the ceiling is strong enough to support the weight of the unit or not. If there is a risk, reinforce the ceiling CAUTION before installing the unit. •...
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 (3) Open the installation hole. (Pre-set ceilings) Main unit • Once the installation hole is opened in the ceiling where the unit is to be installed, pass refrigerant piping, drain piping, transmission wiring, and remote controller wiring Attach the filter to the Force (It is not necessary if using a wireless remote controller)
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 7. DRAIN PIPING WORK CAUTION Be sure to insulate any field piping all the way to the piping In case of PDVE, NDVE type (with drain pump) connection inside the unit. Any exposed piping may cause condensation or burns if touched.
Page 45
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 1. Remove the control box lid. Connect the remote controller Large sealing and power supply (single-phase, 50 Hz 220-240 V or pad (5) Metal clamp (1) single-phase, 60Hz 220V) respectively to the terminal block (accessory) (accessory) and securely connect the earth also (as shown in the figure Metal clamp (1) below).
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 〈 PRECAUTIONS 〉 (1) Install the drain piping. Drain piping connections • Do not connect the drain piping directly to sewage pipes that Drain socket smell of ammonia. The ammonia in the sewage might enter the indoor unit through the drain piping and corrode the heat exchanger.
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 9-2 SPECIFICATIONS FOR FIELD SUPPLIED FUSES CAUTION AND WIRE • Be sure to insulate the duct to prevent condensation from Power-related forming. (Material: glass wool or polyethylene foam, 25 mm thick) Power supply wiring (including earth wire) •...
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 10. WIRING EXAMPLE [ PRECAUTIONS ] • Refer to the “REMOTE CONTROLLER INSTALLATION 10-1 HOW TO CONNECT WIRINGS MANUAL” on how to install and lay the wiring for the remote • Wire only after removing the control box lid as shown in controller.
Page 49
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 [ WIRING EXAMPLE ] CAUTION FOR WIRING No. 1 system When using 1 remote controller for • For connection to the terminal block, use ring type crimp style 1 indoor unit terminals with insulation sleeve or insulate the wirings properly.
Page 50
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 No. 3 system When including BS unit (4) Add remote controller 2 (SUB) to the terminal block for remote controller (P ) in the control box. Power supply (There is no polarity.) single phase 50Hz 220-240V FORCED REMOTE TRANSMISSION...
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 11-3 SETTING THE FILTER SIGN DISPLAY INTERVAL 11. FIELD SETTING AND TEST RUN • Explain the following to the customer if the filter dirt settings 〈Field settings may have to be performed using the have been changed. remote controller, depending on the type of installation.〉...
FXDQ-PDVE(T) / FXDQ-NDVE(T) EDFMT391749 (3) Perform a test run according to the outdoor unit’s installation manual. • The operation lamp of the remote controller will flash when a malfunction occurs. Check the malfunction code on the liquid crystal display to identify the point of trouble. An explanation of malfunction codes and the corresponding trouble is provided in “CAUTION FOR SERVICING”...
Page 56
VRV is a trade mark of Daikin Industries, Ltd. VRV Air Conditioning System is the world’s first individual air conditioning system with variable refrigerant flow control and was commercialised by Daikin in 1982. VRV is the trade mark of Daikin Industries, Ltd., which is derived from the technology we call “variable refrigerant volume.”...
Need help?
Do you have a question about the VRV FXDQ-PDVE and is the answer not in the manual?
Questions and answers