Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Xilin CQDH Series
Summary of Contents for Xilin CQDH Series
- Page 1 CQDH Reach Electric Stacker Operation Manual Spare parts catalogue 2009-11...
- Page 2 Welcome to choose “XILIN” Fork Reach Electric Stacker. We hope our fork reach electric stacker will bring great convenience to your work. Please read the manual carefully before operation. This manual is a common manual. We reserve the right to modify technology of the reach electric stacker.
-
Page 3: Table Of Contents
Table of Contents Configuration diagram…………………………………………………………………………………………1 Main technical parameters…………………………………………………………………………………..2 Use and scope……………………………………………………………………………………………………4 Brief introduction of structure……………………………………………………………………………..4 Using and operation instructions………………………………………………………………………….4 Maintenance and upkeep…………………………………………………………………………………….6 Common faults and trouble shooting……………………………………………………………………7 Maintenance and charge of the storage battery…………………………………………………….9 List of accessories, spare parts and vulnerable parts……………………………………………..10 10. -
Page 4: Configuration Diagram
1. Configuration diagram... - Page 5 2.1 CQDH10AMain technical parameters Model CQDH10A Driving mode Electric Driving mode Stand driving Rated load Q(kg) 1000 Load center distance (mm) Front overhang (mm) Tread (mm) 1290 1380 Service weight(with storage 1350 1385 1420 1450 1480 1850 1950 2050 battery) Axleloading,unladen front/rear 810/570 830/590...
-
Page 6: Main Technical Parameters
Drive motor power Lift motor power Batteryvoltage/nominal V/Ah 24/320 capacity Battery weight Battery dimension（LXWXH） 812x270x535 Noise level at operator’s dB(A) ear, according to DIN12053 2.2CQDH12AMain technical parameters Model CQDH12A Driving mode 电动 Driving mode 站驾式 Rated load Q(kg) 1250 Load center distance (mm) Front overhang (mm) -
Page 7: Use And Scope
Aisle width for pallets 4.34 (mm) 2650 2680 800x1200 lengthways 4.35 Turning radius (mm) 1750 1780 Travel speed，laden/unladen Km/h 4.5/5 4.8/5 Lift speed，laden/unladen 0.095/0.12 Loweringspeedladen/unladen 0.2/0.15 Max.gradeability,laden/unladen 5/12 5.10 Traveling brake Electromagnetic brake Drive motor power Lift motor power Batteryvoltage/nominal V/Ah 24/320 capacity... - Page 8 5.1 Before operation 5.1.1 Before operation, please check if the truck is in normal condition: Is there any oil leakage in the hydraulic pipes? Are the supporting wheels able to operate normally? Is there any block? Faulty stackers are strictly prohibited. 5.1.2 Check if there is any electric power in the batteries with the method indicated in Fig, I.
- Page 9 5.2.2 Operation of handling and stacking As indicated in Fig. I, pull out the general power supply switch, unlock the electric door lock, and drive the stacker to goods pile nearby (the tip of the fork is 30cm from the goods pile). Turn lifting-lowering handle of multi-way valve so as to adjust the height of the fork to a proper position;...
-
Page 10: Common Faults And Trouble Shooting
the internal and external door frames is normal; is there any oil leakage at the hydraulic connection; is there any abnormal wearing and tearing in the mechanical parts; is there any abnormal temperature rise or sparks in the electric part, etc. If there is any abnormal situation, adjustment or trouble-shooting should be conducted promptly. Level II maintenance: Level II maintenance should be carried out as planned. - Page 11 only move forward ② There is a trouble in the circuit board. Repair or replace (or backward) Cut off the power supply at The stacker can not Broken contact. The moving contact cannot be reset. once and replace the head of stop while traveling contactor.
- Page 12 8.1 Initial charge Note: The charging environment requires good ventilation and there should be no open flame, otherwise explosion may occur. 8.1.1 Initial charge should be conducted for batteries that have never been used. Before the initial charge, the surface of the batteries should be cleaned and the batteries should be examined for damage.
-
Page 13: List Of Accessories, Spare Parts And Vulnerable Parts
in the following situation, i.e. equalizing charge. a. The “lag-behind” batteries--- batteries with a voltage lower than that of the other batteries in the charging and discharging process and the batteries having been repaired for failure. (When equalizing charge is conducted, the positive and negative poles of the “lag-behind”... -
Page 14: Warning (Notes)
The stacker is packed with a tray. During transportation, turnover and upside-down are not allowed. Collision is not allowed when lifting and loading onto the truck. Do not damage the outward surface of the stacker when opening the package. 11. Warning (points for attention) 11.1 Read the manual carefully before operation so as to know the performances of the stacker. - Page 15 Consignee: Ex-work No.: Contract No.: Ex-work date: Dimension Name Quantity Remarks weight (L×W×H) CQDH Fork Reach Electric Stacker A complete set. Technical documents, accessories Accessory box and spare parts. Note: 1. The following documents are in the file bag: ①Operation manual of CQDH Fork Reach Stacker 1 volume ②Packing list 1 copy...
- Page 16 10 # SA2 Keyswitch Ke y switchinput J1 - 1 J1-1 J1- 1 Safetyswitchinput SA3 Ha n dle saf e ty swi t ch J1-2 Bac k ward Hac k ward J1- 1 4 （ + ） TMlogic c a rd For w ard Forwar d J 1 -13...
- Page 17 SA2 Key switch Handle switch Direction contactor Direction contactor Controller Main contactor Main contactor Cutbackspeed Slow input Backward Backward Forward Forward SA1 Emergency stop switch 急停 开关 Belly SW Rapid reverse Acceleration adjustment 0-5V Multi-way valve switch KM1 lift c ontact or YB brake coil CURTIS 1207 CONTROLLER;REMA TILLER...
- Page 18 SA2 Key switch FEEDER Power Controller A 10 Backward Backward Forward Forward Rapid reverse Operation handle Rapid reverse 急反 Main contactor Acceleration adjustment 0-5V 180A Acceleration adjustment 0-5V 125A SA1 Emergency stop switch SA1 Emergency stop switch SHUNT Multi-way valve switch Slow down Handle safety switch Decline...
Need help?
Do you have a question about the CQDH Series and is the answer not in the manual?
Questions and answers
hydraulic pump motor is not functioning. Can you help me how to fix it. Thank you
If the hydraulic pump motor of the Xilin CQDH Series is not functioning, follow these steps:
1. Check the control handle position – Ensure it is properly set to horizontal or vertical.
2. Verify the motor switch – Make sure the oil pump motor is turned on.
3. Inspect for damage – If the motor is damaged, it needs to be repaired or replaced.
If the issue persists after these checks, replacing the motor may be necessary.
This answer is automatically generated