Sealey SMS216.V2 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
if the multi-tool is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information. It is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
IMPORTANT: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
1.1.3.
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualified electrician.
If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is
preferred since any appliance plugged into it will be protected. The cable core section is important and
should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this product and for others which may
be used in the other output sockets, we recommend the use of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is
marked for outdoor use.
1.2. GENERAL SAFETY
Familiarise yourself with the applications, limitations and potential hazards of the saw.
9
WARNING! Disconnect the saw from the mains power before changing accessories, servicing or performing any maintenance.
‰
The machine must only be serviced by a qualified person or service agent. Contact your Sealey stockist for information.
9
Select a work area suitable for the saw and keep the area clean, tidy and free from unrelated materials. Ensure that there is adequate
9
lighting.
Wood dust can be harmful to health by inhalation and skin contact. Concentrations of small dust particles in the air can form an
9
explosive mixture. Ensure that there is adequate ventilation and that the saw is attached to a dust-extraction unit.
Maintain the saw in good condition, check moving parts alignment regularly. Keep saw blades clean and sharp.
9
Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly for damaged parts.
‰
A guard, or any other part, that is damaged should be repaired or replaced before the saw is next used. The safety guard is a mandatory
9
fitting where the saw is used in premises covered by the Health & Safety at Work Act.
Before commencing work, ensure the saw blade is set to cut in the correct direction, securely fastened, sharp and is compatible with the
9
machine, spindle speed and the material to be cut. Never use a saw blade if damaged, bent or warped. Use only recommended saw
blades.
Remove adjusting keys and wrenches from the machine and the vicinity before switching on.
9
Machine operators must have received sufficient training and instructions relating to the dangers associated with the machine, the
9
precautions to be observed and the requirements of the Wood Working Machines Regulations.
© Jack Sealey Limited
Ø216MM SLIDING COMPOUND MITRE SAW
SMS216.V2
MODEL NO:
Wear a mask
Wear ear
protection
Original Language Version
Warning!
Wear
protective Laser beam
gloves
RECOMMENDED FUSE
RATING: 13A
,
SMS216.V2 Issue:1 18/03/21