1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify the circuit board. Disconnect the AC power and DC power jack before servicing.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than a people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
Page 8
2. Product specifications Model UA40C6900VH / UE40C6000RH Feature RF, 2-HDMI, 1-Component, 1-AV, 1-USB 2.0, D-SUB, 1-SCART(Mideast Africa, EU only) ሪ Brightness : 500cd/m ሪ Contrast Ratio : 3,000,000:1 ሪ Response time : 6ms ሪ Dynamic contrast, Super-PVA ሪ PIP(in HDMI 1, 2, Component1, PC Mode and Sub picture is available only in TV analog mode) ሪ...
Page 9
2. Product specifications Model UA46C6900VH / UE46C6000RH Feature RF, 2-HDMI, 1-Component, 1-AV, 1-USB 2.0, D-SUB, 1-SCART(Mideast Africa, EU only) ሪ Brightness : 500cd/m ሪ Contrast Ratio : 3,000,000:1 ሪ Response time : 6ms ሪ Dynamic contrast, Super-PVA ሪ PIP(in HDMI 1, 2, Component1, PC Mode and Sub picture is available only in TV analog mode) ሪ...
Page 10
2. Product specifications Model UA55C6900VH Feature RF, 2-HDMI, 1-Component, 1-AV, 1-USB 2.0, D-SUB, 1-SCART(Mideast Africa, EU only) ሪ Brightness : 500cd/m ሪ Contrast Ratio : 3,000,000:1 ሪ Response time : 6ms ሪ Dynamic contrast, Super-PVA ሪ PIP(in HDMI 1, 2, Component1, PC Mode and Sub picture is available only in TV analog mode) ሪ...
2. Product specifications 2-2. Detail Factory Option If you replace the main board with new one, please change the factory option as well. ※ The options you must change are “Type, LOCAL SET, Front color". UA40C6900VH UA46C6900VH Model Name UE32C6000R UA55C6900VH...
2. Product specifications 2-3. Spec Comparison to the Old Models Model UC6900 / UC6000 UB6000 Design Display Type LED TV LED TV Resolution 1920 x 1080 1920 x 1080 LCD Panel TFT LCD Panel 100Hz TFT LCD Panel 100Hz 32"(UC6000 only) / 40"(Both) / Screen Size 40"...
Page 13
2. Product specifications 2-4. Channel Table CHANNEL FREQUENCY TABLE OUTPUT FREQUENCY : ANALOG fv:45.75MHz, fs:41.25MHz DIGITAL Fc:44MHz TUNING STEP SIZE : FIRST PLL 250KHz SECOND PLL 62.5KHz (Unit : MHz) AREA ASIA HONG SOUTH Number BAND BAND BAND BAND BAND W/EUROPE E/EUROPE...
Page 14
2. Product specifications (Unit : MHz) AREA ASIA HONG SOUTH Number BAND BAND BAND BAND BAND W/EUROPE E/EUROPE KONG U/K INDONESIA AFRICA 791.25 791.25 791.25 791.25 791.25 799.25 799.25 799.25 799.25 799.25 807.25 807.25 807.25 807.25 807.25 815.25 815.25 815.25 815.25 815.25 823.25...
Page 15
2. Product specifications (Unit : MHz) AREA Number AUSTRALIA BAND CHINA BAND AMERICA BAND 46.25 57.25 49.75 64.25 57.75 55.25 86.25 65.75 61.25 95.25 77.25 67.25 102.25 85.25 77.25 175.25 168.25 83.25 182.25 176.25 175.25 189.25 184.25 181.25 196.25 192.25 187.25 209.25 200.25...
Page 16
2. Product specifications (Unit : MHz) AREA Number AUSTRALIA BAND CHINA BAND AMERICA BAND 695.25 823.25 699.25 702.25 831.25 705.25 709.25 839.25 711.25 716.25 847.25 717.25 723.25 855.25 723.25 730.25 863.25 729.25 737.25 735.25 744.25 741.25 751.25 747.25 758.25 753.25 765.25 759.25 772.25...
Page 17
2. Product specifications Cable CHANNEL (Unit : MHz) AREA ASIA HONG SOUTH Number BAND BAND BAND BAND BAND W/EUROPE E/EUROPE KONG U/K INDONESIA AFRICA 105.25 103.25 103.25 105.25 105.25 112.25 111.25 111.25 112.25 112.25 119.25 119.25 119.25 119.25 119.25 126.25 127.25 127.25 126.25...
Page 18
2. Product specifications (Unit : MHz) AREA Number AUSTRALIA BAND CHINA BAND AMERICA BAND 105.25 112.25 73.25 112.25 120.25 55.25 119.25 128.25 61.25 126.25 136.25 67.25 133.25 144.25 77.25 140.25 152.25 83.25 147.25 160.25 175.25 154.25 224.25 181.25 161.25 232.25 187.25 168.25 240.25...
Page 19
2. Product specifications (Unit : MHz) AREA Number AUSTRALIA BAND CHINA BAND AMERICA BAND 475.25 481.25 487.25 493.25 499.25 505.25 511.25 517.25 523.25 529.25 535.25 541.25 547.25 553.25 559.25 565.25 571.25 577.25 583.25 589.25 595.25 601.25 607.25 613.25 619.25 625.25 631.25 637.25 643.25...
2. Product specifications 2-5. New Function Introduction 2-5-1. Movie Plus: MJC(Motion Judder Cancellation) Technology Example • Motion Judder cancellation for HD film image. • Adaptive Recursive Search (ARS) - Implementation IPC/MJC at same time <Motion Judder> - Search Range Horizontal : ± ±...
Page 21
2. Product specifications 2-5-2. Internet@TV Getting Started with Internet@TV Note Configure the network settings before using Internet@TV. For more information, refer to “Network Connection”. Unsupported fonts within the provider’s content will not display normally. Slow responses and/or interruptions may occur, depending on your network conditions. ...
Page 22
2. Product specifications Setting up Internet@TV Settings Create IDs and configure Internet@TV settings from this screen. Highlight Settings using ◀ and ▶ buttons and press the ENTER button. Account Login Ticker Autorun may not be supported depending on country. Ticker Autorun (Off / On): Enable/disable ticker autorun upon powering on the TV.
Page 23
Samsung Apps Various widgets are available from here, organized into different categories. Some widgets have a download fee. Using the colour buttons with the Samsung Apps. A Red button: To log in to the internet service. B Green button: To change the view mode.
Page 24
2. Product specifications Yahoo Internet@TV provides an integrated Internet and television experience powered by the Yahoo!® Widget Engine. You can monitor financial stocks, share photos with friends and family, and track news and weather all through the Yahoo!® Widget Engine. ...
Page 25
2. Product specifications PROFILE Widget Set up user profiles through Profile Widget. You can set up multiple profiles, each with its own list of widgets. Use the Switch Profile option to switch to a different user profile. There must be at least two registered profiles. For instructions on adding a profile, refer to Administrative Controls. ...
Page 26
2. Product specifications Yahoo OOBE (Out Of Box Experience) Description A. All users go through OOBE (Guided Setup) to access the dock the first time. B. All users must specify a location and accept the TOS (Terms Of Service) before the TV Widgets service are accessible.
Page 27
2. Product specifications Tutorial: Screens explaining how the docks work. Tutorial: Screens explaining the sidebar and global nav buttons. Final screen before dock comes up. 2-21...
Page 28
2. Product specifications Profile Widget Overview A. The Profile widget is the way to configure your widget environment for your user profile. With the settings widget you can configure: i. Profile Management: Create, edit and switch profiles. ii. Security Settings: Setup a Profile and/or Owner PIN for security purposes. iii.
Page 29
2. Product specifications Flickr TV Widget Description A. Flickr TV Widget is a Widget for displaying photos from Flickr. You can view your: Personal photos Your sets of photos iii. Explore Flickr’s user community photos Your favorite photos Your contacts’ photos Your groups Initial Sidebar View A.
Page 30
2. Product specifications Initial Sidebar View A. If the user is not signed and user is signed but user has no photo then the default images will be displayed from the Flickr Explore category. B. If the user is signed in and the user has 1 photo or more photos, then the photos will be displayed in the top portion of the Widget Sidebar.
Page 31
2. Product specifications Weather Widget Overview A. The Weather Widget utilizes the “Tab View" layout of the Widget Sidebar i. The tab view is a viewable area than contains groups of user interface elements organized under tab headers. ii. The tab view does not have a page control. Using both tabs and page controls in the same view is prevented to avoid confusion.
Page 32
2. Product specifications News Widget Overview A. The News Widget sidebar will then be displayed B. Several stories will be displayed in the top featured area of the Widget Navigation will be available to move from one story to the next These stories are automatically updated by Yahoo! iii.
Page 33
Compatibility problem. Before connecting your device to the TV, please back up your files to prevent them from damage or loss of data.SAMSUNG is not responsible for any data file damage or data loss. Do not disconnect the USB device while it is loading.
Page 35
* ScreenShare(RUIS/RUIC) : You can see and control the UI of Home Network server supported device in your TV screen. Similarly, samsung TV provide the remote controller UI for the Home Network supported devices. <Connection>...
3. Disassembly and Reassemble 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the LED TV. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly and Reassembly Cautions: 1.
Page 39
3. Disassembly and Reassemble Description Picture Description Screws Pull out a AC Power Cord. 3. Lift up the rear-cover. 4. Remove the cables and screws from SMPS, Main board and Woofer and Bracket stand link. 6001-002283 (M3xL5) 6001-000115 (M3xL10) 5. Remove the panel bracket screws from the panel.
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting Check the various cable connections first. • Check to see if there is a burnt or damaged cable. • Check to see if there is a disconnected or loose cable connection. • Check to see if the cables are connected according to the connection diagram. Check the power input to the Main Board.
Page 41
4. Troubleshooting Simple flow chart of malfunction Does the TV turn on? Can you see anything on the screen? Can you see OSD menu running on the screen? Can you see Digital Channel broadcast ? Check LVDS cable connected Check the Power Cord to Main Board.
Page 43
The WLAN does not work. An explanation of Equipment other than the WLAN USB stick supplied by Samsung Electronics (as a bundle) will not work. Media play The sharer must support IEEE 801.11 g/b. IEEE 801.11 n is supported.
Page 44
The DLNA server that I could see on the PC Share Manager 1.Check if the PC is turned off. 2. Check if the Samsung TV has suddenly disappeared. What Search TV is set to reject connections in the access control menu should I do? of the Samsung PC Share Manager.
Page 45
4. Troubleshooting I cannot play files with the wmv or flv DLNA Video Play The video play function is not supported for files with these extension. extensions. I cannot use the 20 second Seek DLNA Video Play To use the Seek function while playing at 2x Fast Forward, function while playing at 2x Fast press the Play button to first make the playing speed Forward.
Page 46
Images provided by Samsung.com or a 3rd party content personal photos using the Gallery Content Library provider linked to Samsung.com will not be played in the function. How can I do this? [Contents Library]. However, you can use the SlideShow function of WiseLink Pro.
Page 47
4. Troubleshooting 4-1-1. No Power The LEDs on the front panel do not work when connecting the power cord. Symptom The SMPS relay does not work when connecting the power cord. The units appears to be dead. The IP relay or the LEDs on the front panel does not work when connecting the power cord if the cables are improperly connected or the Main Board or SMPS is not functioning.
Page 50
4. Troubleshooting 4-1-2. No Video (Analog PC signal) Symptom Audio is normal but no picture is displayed on the screen. Check the PC source Major Check the Arsenal, Check the Valencia. checkpoints Refer to the next page to check the lacation such a CN1201 or IC201 SVC Manual mentioned. Power indicator LED is off.
Page 53
4. Troubleshooting 4-1-3. No Video (HDMI 1, 2 - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source. Major Check the HDMI switch, Check the Valencia. checkpoints Refer to the next page to check the lacation such a CN201 or IC201 SVC Manual mentioned. Power indicator LED is off.
Page 54
4. Troubleshooting Location (Main) BOTTOM Detail #9, #10 of D3903 TX4_CLKP #4, #5 of D3904 TX4_CLKN TX2_CLKP #9, #10 of D3905 #9, #10 of D3907 TX2_CLKN #4, #5 of D3906 #4, #5 of D3908 #9, #10 of D3901 TX1_CLKP #4, #5 of D3902 TX3_CLKP TX1_CLKN TX3_CLKN...
Page 56
4. Troubleshooting 4-1-4. No Video (Tuner_CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Tuner CVBS source. Major Check the Tuner, Check the Valencia. checkpoints Refer to the next page to check the lacation such a CN201 or IC201 SVC Manual mentioned. Power indicator LED is off.
Page 59
4. Troubleshooting 4-1-5. No Video (Video CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Video CVBS source Major Check the Valencia. checkpoints Refer to the next page to check the lacation such a CN201 or IC201 SVC Manual mentioned. Power indicator LED is off.
Page 62
4. Troubleshooting 4-1-6. No Video (Component) Symptom Audio is normal but no picture is displayed on the screen. Check the Component source Major Check the Valencia. checkpoints Refer to the next page to check the lacation such a CN201 or IC201 SVC Manual mentioned. Power indicator LED is off.
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment instruction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control INFO MENU MUTE Power on - If you have Factory remote - control PICTURE ON INFO FACTORY...
Page 67
4. Troubleshooting 4-3-3 Factory Data Option Item Range OPTION Factory Reset Inch Vendor(A:AMLCD, D:CMO, L:AUO, I:CPT) Panel frequency (6:50/60Hz, 1:100/120Hz, 2:200/240Hz) Panel(A:AG, T:TN, U:UC) Select Type Resolution(F:FHD, H:HD, U:UD) Panel Type Panel 1st/2nd(1st:0, 2nd:1) BLU (C:CCFL, L:LED, E:EDGE LED) ex) 32D1UF0E : Vendor : CMO inch : 32 120Hz FHD U/C Edge LED panel Local Set EU, EU_Italy, EU_Africa, EU_Israel, NORDIG, AD_Au, CIS...
Page 68
4. Troubleshooting Control Item Range EDID EDID ON/OFF EDID WRITE ALL SUCCESS EDID WRITE PC SUCCESS EDID WRITE HDMI SUCCESS EDID WRITE HDMI1 … EDID WRITE HDMI2 … EDID WRITE HDMI3 … EDID WRITE HDMI4 … EDID 1.2PORT NONE,Not Support NONE, W-Milky, T-M-Brn, T-W-Brn, T-W-Gray, W-D-Gray, W-M-Whit Front Color W-Violet, T-C-Gray, T-R-BLK, S-BLK, S-C-Gray...
Page 69
4. Troubleshooting Alternate Del ON/ OFF OTN Server Type development / operating OTN Test Server ON/ OFF OTN Support ON/ OFF OTN Reset OTN Duration ON/ OFF OTN Fail Test ON/ OFF PC Auto Ident Auto/ Enable IIC BUS STOP ON/ OFF Emergency Log Copy View Log...
Page 70
4. Troubleshooting Item Range Test for input Scaler. Pattern Sel : off, White, Grey, Balck, Red, Green, Blue If you can RRC PC Mode : On/Off Test Pattern see pattern Logic Pattern Sel well, there is a Logic Level Sel problem at input of Scaler Panel Auto Setting...
Page 71
4. Troubleshooting Item Range WB Movie W/B Movie ON/OFF ON/OFF MODE Dynamic/Movie/Natural Color Tone Cool/NORMAL/WARM1/WARM2 MSub Brightness Msub Contrast N_Rgain N_Bgain N_Roffset N_Boffset W1_Rgain … W1_Bgain … W1_Roffset … W1_Boffset … W2_Rgain … W2_Bgain … W2_Roffset … W2_Boffset … Movie Contrast Movie Bright Movie Color Movie Sharpness...
Page 72
4. Troubleshooting Item Range ColorMapping Auto_Red_R Auto_Red_G Auto_Red_B Auto_Green_R Auto_Green_G Auto_Green_B Auto_Blue_R Auto_Blue_G Auto_Blue_B Auto_Yellow_R Auto_Yellow_G Auto_Yellow_B Auto_Cyan_R Auto_Cyan_G Auto_Cyan_B Auto_Magenta_R Auto_Magenta_G Auto_Magenta_B Item Range EPA 3D Standard Contrast Standard Brightness Standard Sharpness Standard Color Standard Tint Standard Backlight 3D Contrast 3D Brightness V_3D PWM Delay_60 V_3D ANA Delay_60...
4. Troubleshooting Setting the Hotel Option Data 4-4. Setting the Hotel Option Data 4-4-1. Stand-alone Mode Stand-alone Mode ¦ → → → → To Enter: Press the MUTE ENTER buttons in order. To Exit from this menu : power off and turn on again. Item initial Value Description...
Page 81
4. Troubleshooting Item initial Value Description Selection of the way to update clock data • Auto: Use clock data from server when the TV is in the interactive mode. Local time Manual • Manual: Use clock data from DVB channel or manual clock setting when the TV is in the stand-alone mode.
Page 82
→ buttons in order, in normal operation state. INFO MENU EXIT To Exit from this menu : Power Off and Turn On again. (Press button with general SAMSUNG remocon) POWER Item initial Value Description Hotel Mode Hotel mode(Stand alone) on/off...
Page 83
4. Troubleshooting Item initial Value Description Local time Manual Selection of the way to update clock data • Auto: Use clock data from server when the TV is in the interactive mode. • Manual: Use clock data from DVB channel or manual clock setting when the TV is in the stand-alone mode.
4. Troubleshooting 4-5. White Balance - Calibration 4-5-1 White Balance -Calibration AV Calibration ADC/WB Comp Calibration PC Calibration HDMI Calibration 4-5-2 Service Adjustment You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration Adjust spec. 1.
Page 85
4. Troubleshooting Method of Color Calibration (AV) 1) Apply the NTSC Lattice (N0.2) pattern signal to the AV IN 1 port 2) Press the Source key to switch to “AV1” mode 3) Enter Service mode 4) Select the “ADC/WB” and “ADB” menu 5) Select the “AV Calibration”...
4-6. Servicing Information 4-6-1 Upgrading the Software Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung call center at 1-800- SAMSUNG (726-7864) to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
4. Troubleshooting 4-7. Hotel Plug & Play Hotel Plug & Play is a function that automatically performs the Hotel mode selection, Country Setup, Clock Setup and Hotel Plug & Play ¦ Picture mode Setup once. Hotel Plug & Play is a function that automatically performs the Hotel mode selection, Country Setup, Clock Setup and Picture ...
Page 88
– When Standalone Plug & Play is selected from “Easy Set Up” OSD, “Select Menu Language” OSD is displayed. – Initial Highlight : English – Display time: OSD timeout and operation are the same as Samsung's consumer TV models. – If button is pressed, “Select Area”...
Page 89
Interactive : When TV is powered-up initially it sends command to identify SBB/STB, if identified TV switches to ONLINE mode and full control is through SBB/STB. In ONLINE TV stops receiving IR(Samsung remote) commands and acts mode and full control is through SBB/STB. In ONLINE TV stops receiving IR(Samsung remote) commands and acts according to interface protocol.
Page 90
4. Troubleshooting Connecting the TV with SBB Connecting the TV with SBB TV Rear Panel UA40C6900VHXZN UE40C6000RHXXC UE46C6000RHXXC UA46C6900VHXZN ETH MODEM UA55C6900VHXZN Data Cable TV Rear Panel UA40C6900VHXXY UA46C6900VHXXY ETH MODEM UA55C6900VHXXY UA40C6900VHXRD Data Cable UA46C6900VHXRD UA55C6900VHXRD TV Rear Panel UE32C6000RHXXC UE40C6000RHXXC UE40C6000RHXXC...
Page 91
Connecting the Bathroom Speakers 4. Troubleshooting You can connect the Bathroom Speakers in the following method. Connecting the Bathroom Speakers Connecting through the Variable Output (available without an external amplifier) ¦ TV Rear Panel Volume Control Box VOL+ VOL- Speaker 1.
Page 92
VOL - DOWN VOL - UP ( Black /Red 2 ) ( Shield Wire 3 ) ( White 1 ) 4. Troubleshooting Connect through the Fixed Output (available without an external amplifier) Connect through the Fixed Output (available without an external amplifier) ¦...
Page 93
4. Troubleshooting Connecting the MediaHub HD Connecting the MediaHub HD Output of any external source connected to MediaHub HD on hotel desk. MediaHub HD Rear HDMI RS/232 TV Rear Panel 1 RS-232 Data Cable 2 HDMI cable 1. Connect the port of the TV and the RS/232 port of the MediaHub HD.
Page 94
TV to the PC/AUDIO port of the RJP. ✎ (Remote Jack Pack) compatible with this Samsung TV is TeleAdapt TA-7610, TA-7650 (HD) and TA-7660 (HD Plus). y RJP (Remote Jack Pack): RJP stands for Remote Jack Pack. The RJP is a hardware module that has different Audio Video inputs (A/V, Audio, PC and HDMI) and corresponding outputs.
Page 95
4. Troubleshooting y The following table shows the approximate time in seconds to switch from the TV to the input source, based on the priority. ✎ Scenario 1: When no inputs are connected. Source To Connect 2 Sec 0.7 Sec HDMI 3.9 Sec ✎...
Page 96
4. Troubleshooting Welcome Message Welcome Message ¦ Welcome message is a feature to display custom message on TV, every time TV is turned on by Guest in Hotel room. – Welcome message settings are placed in Hotel Option Menu. – Welcome message should be ON in order to display the message on power on. Hotel Mode RJP Priority HDMI Clone USB to TV...
Page 97
– No File will be displayed when there is no file to copy in USB. y Logo File Format – Only BMP format is supported and File name must be samsung.bmp. – Maximum resolution is 960 x 540. – Image is not changed on a large or small scale during power on.
Page 98
4. Troubleshooting USB Cloning USB Cloning ¦ USB Cloning is a function to download user configured settings (Picture, Sound, Input, Channel, Setup, and Hotel Setup) from one TV set and upload the same to other TV sets. All the user-defined settings from the TV (Master Set) can be copied to the USB device. USB Cloning is in hotel option menu in both Standalone and Interactive mode.
Page 99
4. Troubleshooting Multi Code Remocon Multi Code Remocon ¦ Multi Code Remocon is a special transmitter which is designed to control each TVs with one remote. This function is useful where there is more than one TV in one location like hospital Set ID number will be displayed in source osd.
5. Wiring Diagram 5-3. Connector Functions Connector Function Supply main power and dimming signal from IP board to Main Board. CN201 CN802 CN1401 CN505 The LVDS signal transfered from Main Board to Panel . 5-4. Cables Main IP (18P) Main - TCON 32"...