Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bose QC25
Summary of Contents for Bose QC25
- Page 1 BTunes for Bose QC25 User’s manual...
-
Page 2: Table Of Contents
Content ■ Before use…………………………………………………...…1 1. Overview ....…………………………………...…….1 …………………………………………….2 2. Charging the BTunes ■ Getting started…………………….……………………………2 ............2 Powering on/off the BTunes 2. Installation...................3 3. Pairing /Connecting..............3 1)Pairing the BTunes with Bluetooth cellphone..……………3 2)Pairingthe BTunes with Bluetooth transmitter......4 3)Pairing the BTunes with multi-point devices......5 4. -
Page 3: Before Use
Thank you for choosing the BTunes for Bose QC25. Please read this user’s manual carefully before use. ■ Before use BTunes for Bose QC25 supports streaming CD quality music from your smart devices, and make phone calls too. 1. Overview 2.5mm audio input jack... -
Page 4: Charging The Btunes
2. Charging the BTunes When the BTunes need to be charged, it will emits “Battery low” and the red LEDflashes instead of blue LED. Pleaserecharge the battery of the BTunes. 1) Plug the USB charging cable into the charging jack of a PC or a charger. 2) Plug the end of USB charging cable into the USB port on the BTunes. -
Page 5: Installation
2) Press and hold MFB button about 7s and release it till red and blue LED flash alternately, voice prompt “Pairing”. 3) Select “The BTunes QC25/5” from Bluetooth list on your cellphone to pair/connect. After connected, the Blue LED flash twice every 4s and... -
Page 6: Pairingthe Btunes With Bluetooth Transmitter
Remarks: ◆ Pairing mode will last for 2 minutes, if not paired/connected with devices, the BTunes will into standby mode. ◆ After successful pairing, the BTunes and devices will remember each other, they will not need to re-pair next time. When the BTunes is powered on, it will connect to the last connected devices automatically. -
Page 7: Pairing The Btunes With Multi-Point Devices
3）Pairing the BTunes with multi-point devices The BTunes can connect with two Bluetooth devices at the same time. The general pairing procedures are as follows: 1)Pairing the BTunes with device one. 2) Turn on the BTunes and make it enter into pairing mode again, and pair with device two. -
Page 8: Making A Call
5. Making a call 1) Basic operation Functions Status of headset Operation Prompt tone Short press MFB call Cancel a call Calling button once terminated Short press MFB Ringing Answer button once Answer a call Press MFB Reject a call Ringing Reject about 2 seconds... - Page 9 No prompt Press volume Volume down During a call down button tone Transfer Transfer Press MFB conversation During a call about 2 seconds audio to cellphone Transfer Press MFB Transfer conversation During a call about 2 seconds audio to headset Microphone Double click During a call...
-
Page 10: Playing Music
Note: When pressing the answer button on some cell phone, the call will be transferred to the cell phone. You can switch the call to the BTunes through transfer conversation or operating on the smart devices. Please refer to your smart devices user manual for further information. -
Page 11: Led Indicator
Notes: ◆ When the BTunes is connected with two Bluetooth devices, the BTunes can only play music from one device and need pause current music and play music from the other device. ◆ If you want to remote control last/next song, pause/play, it needs your Bluetooth smart devices or Bluetooth transmitter paired with the headset to support AVRCP profile, please refer to the user’s manual of your smart devices or Bluetooth transmitter for further information. -
Page 12: Factory Reset
8. Factory Reset In the status of power off or charging, long press MFB button and button about 3 seconds and release it until the red and blue LED flashes simultaneously. Remarks: After factory reset, the paired list of the BTunes will be deleted. After power on again, the BTunes will enter pairing mode automatically, and you need to re-pair and connect with Bluetooth devices. -
Page 13: Faqs
■ FAQs 1.What does it mean when red LED flashes instead of blue LED? Battery is low, it’s time to charge the battery. 2.Why is the red LED off when charging? a) Please make sure the charging device connect with the BTunes correctly; b) The battery may be drained fully. -
Page 14: Specifications
■ Specifications Bluetooth version Bluetooth V5.0 Bluetooth profiles HFP,HSP, A2DP and AVRCP Operating distance 10 meters Music time Up to 10 hours Standby time About 300 hours Charging time About 1.5 hours Charging input DC 5.0V /500mA Weight About 11 g Measure 75*46*13.5mm... - Page 15 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the QC25 and is the answer not in the manual?
Questions and answers