Related Manuals for Siemens 1-3 Control Technology p1 Series
Summary of Contents for Siemens 1-3 Control Technology p1 Series
- Page 1 Installation / Replacement Instructions p1 series i-3 Control Technology Instruction Manual P/N:12-A-1094-01 Rev. 1...
- Page 2 Contact your local equipment for the first time after glasses or face shields, flash clothing, Siemens representative before using initial installation or maintenance is etc., in accordance with established these products to clean or lubricate potentially dangerous.
- Page 3 P1 Panel with i-3 Control Technology Table of Contents Chapter 1 Introduction Overview Scope Parts Illustration Chapter 2 Receiving, Handling & Storage Receiving Identification Inspection and Unpacking Shipping Damage Claim Procedure Handling Storage Chapter 3 Installation Preparation for Installation Lighting Control Assembly Layout P1 Enclosure Mounting Installation P1 Interior with i-3 Control Technology Installation Additional BQD Breaker and CPOD Installation...
- Page 4 Siemens sales office. The contents of this instruction manual shall not become part of or modify any prior of existing agreement, commitment or relationship. The sales contract contains the entire obligation of Siemens. The warranty contained in the contract between the parties is the sole warranty of Siemens.
- Page 5 Chapter 1 Introduction Overview The principal standards which apply Siemens P1 Series Lighting Panel are: with i-3 Control Technology is a Siemens P1 Series Panel integrated ½National Electric Code NFPA 70 with i-3 Control Technology compo- ½NEMA PB1, NEMA 250 nents within the panel.
- Page 6 Chapter 1 Introduction Parts Illustration Figure 1.2 below shows the front view of P1 panel with i-3 Control Technology components. MLO/Main Box/Can Breaker Space Data Rail Data Rail BQD Breaker CPOD No Feed Through Lug Ribbon Cable Class 2 Wire Barrier (*) Class 2 Wire Barrier...
- Page 7 Dry-contact input connectors separate shipment package. Refer to (inside the i-3 Controller) 4. Notify the Siemens sales office the shipping slip information to immediately of any damage. identify all items included in the If there are any shortages or shipping package.
- Page 8 Siemens sales heat to prevent condensation of office. Approval must be obtained by moisture in the equipment.
- Page 9 Chapter 3 Installation Preparation for Installation For installation/replacement of i-3 Prior to installation of the panel, Control Technology in Siemens P1 study this instruction manual and panel, the following conditions have the drawing package, such as to be met: general arrangement, one line diagram, schematic drawings, wiring 1.Branch circuit breakers are Siemens...
- Page 10 For retrofit desiring this feature contact a Siemens sales representative for ordering information. Note: For repair or replacement of panel components, use existing hardware. If existing hardware is damaged or lost, contact Siemens technical assistance for hardware specifications.
- Page 11 Chapter 3 Installation Figure 3.2 below illustrates i-3 Control Technology Components. Data Rail Data Rail CPOD i-3 Controller Figure 3.2 i-3 Control Technology Components P1 Enclosure Mounting P1 Interior with i-3 CONTROL Installation TECHNOLOGY Installation For the mounting location P1 Interior with i-3 Control information of the Lighting Panel Technology may be factory cabinet, refer to the latest edition...
- Page 12 Chapter 3 Installation Mounting Holes Mounting Holes Figure 3.3 Interior Mounting Holes Location Interior mounting holes are to be Additional BQD Breaker and CPOD Installation aligned with the bolt-on screws installed on the P1 enclosure base In case additional BQD breakers and and tighten the provided wing nuts CPODs need to be installed in the to secure the position of the interior.
- Page 13 Chapter 3 Installation Figure 3.4 Low Voltage Conduit Entry Access (Dimensions are in inches.) Communication Wiring Input Wiring Access Access Center Line Sleeve conduits for input and the P1 interior is installed in the Chapter 4 - Inspection and Testing. communication wiring barriers are enclosure to prevent physical 1.Make sure the dead front is...
- Page 14 Chapter 4 Inspection and Testing Testing that should be attached do not show Perform the following tests prior to on the controller screen then energizing the panel: de-energize the panel, remove the 1. Disconnect the i-3 Control dead front and check all connections. Technology controller from the Once all CPOD modules are bus by pulling the fuse and...
- Page 15 Siemens sales office. Dangerous voltages are present in the equipment which can cause death, serious injury or property damage. Always disconnect and lock off all power to the equipment before maintenance.
- Page 16 Chapter 6 System Components BQD Circuit Breaker Description Figure 6.1 and 6.2 below illustrate BQD circuit breaker layout information. Breaker Handle Load Side Mounting Figure 6.1 BQD 15A Breaker Side View BQD Line Connection Load Lug Terminal Figure 6.2 BQD 15A Breaker Top V Catalog Numbers Interrupting Ratings Continuous...
- Page 17 Chapter 6 System Components Breaker Barrier Installing BQD Circuit Breakers Load Side Into Panel Mounting 1. Disconnect and lock off all power sources supplying this panel 2. Remove the P1 Panel trim and dead front. 3. Make sure that the handle is at off position before installing the circuit breaker.
- Page 18 CPOD is a remotely operated 2. Remove P1 Panel trim and dead electro-mechanical contactor device front. that is attached to Siemens BQD 3. Unscrew the screw connecting the molded case circuit breaker. The BQD line bar connection with the purpose of a CPOD is to allow panel bus bar.
- Page 19 Chapter 6 System Components Figures 6.5 and 6.6 below are the snapshots of a 1-pole CPOD. D. CPOD Load Lug B. Mechanical E. CPOD Status Indicator Connector A. Tang/Conductor Tab C. Manual Override Figure 6.5 CPOD Top View Figure 6.6 CPOD Side View Components Description...
- Page 20 Chapter 6 System Components D. CPOD Load Lug A. Tang/Conductor Tab Tang/conductor tab electrically The CPOD load lug has the same connects the circuit breaker to form and appearance as the BQD the CPOD. In order to secure the circuit breaker load lug. The torque connection of CPOD to the breaker, requirements can be found on the circuit breaker labeling.
- Page 21 2. Remove the P1 Panel trim and dead front. 3. Verify that the circuit breaker is Siemens Type BQD rated 20 amps or less. Information is located on the circuit breaker label. 4. Move the handle of the breaker to Tang "OFF"...
- Page 22 Chapter 6 System Components Figures 6.11 and 6.12 below are snapshots of DR09 assembly and PCB. Screws into panel deadfront support Screw to secure bracket (4 total) the data rail lid Mounting Bracket Removing CPOD From Panel 1. Disconnect and lock off all power sources supplying this panel.
- Page 23 Chapter 6 System Components Panel deadfront support bracket Holes are aligned Installing Data Rail Into Panel Data Rail 1. Disconnect and lock off all power Mounting sources supplying this panel. Bracket 2. Remove panel trim and deadfront. 3. Follow these guidelines for data rail orientation.
- Page 24 Chapter 6 System Components Removing Data Rail From Panel 1. Disconnect and lock off all power sources supplying this panel. 2. Remove panel trim and deadfront. 3. Loosen the screw (2 total) that secures the data rail lid as shown in figure 6.14 to open the lid for CPOD and ribbon cable connections access.
- Page 25 Chapter 6 System Components Panelboard Neutral Bar Installing Neutral Extension Into Panel 1. Disconnect and lock off all power sources supplying this Neutral panel. Extension Bar 2. Remove the P1 Panel trim and deadfront. 3. Refer to figure 6.15 and 6.16 for orientation of the neutral.
- Page 26 Chapter 6 System Components i-3 Controller Description Figure 6.18 below shows the front view of i-3 controller Ribbon Cable Ribbon Cable Communication Interface Door Switch Controller RS485, Inputs Cover Reset Switch, Analog I/O Auto/ Manual Switch Mounting Mounting Bracket Bracket Wiring Access Figure 6.18...
- Page 27 Chapter 6 System Components Installing i-3 Controller Into Panel Mounting Holes 1. Disconnect and lock off all for Controller power sources supplying this Bracket panel. 2. Remove the P1 Panel trim and deadfront. 3. Remove the neutral extensions if installed. 4.
- Page 28 Chapter 6 System Components Removing i-3 Controller From Panel 1. Disconnect and lock off all power sources supplying this Figure 6.22 panel. Ribbon Cable 2. Remove P1 Panel trim and dead front. 3. Disconnect/unplug the ribbon cable connector from the data rail.
- Page 29 Chapter 6 System Components Ribbon Cable Connections The ribbon cable has symmetrical connectors, so that either connector can be used for either connection. In order to eliminate the risk of installing the connector in the wrong orientation, each connector of the Figure 6.23 ribbon cable is equipped with i-3 Controller I/O Board with cover removed...
- Page 30 Appendix A P1 with i-3 Control Technology Panel Specification The table below lists the specifications of a P1 with i-3 Control Technology. Table A1 Panel Specification Max Voltage 480Y/277V AC Max System 1-Phase, 3-Wire 3-Phase, 4-Wire Mains Main Lugs 125A - 250A Main Breaker 100A - 250A Panel Circuits...
- Page 31 Appendix B Label Information The table below lists all labels provided on the P1 with i-3 Control Technology Panel. Table B1 Label information Part Number Description Label Location 15-A-1047-01 Deadfront kit label On the inside of the deadfront below the controller's cutout 11-C-1044-01 Data Rail rating label...
- Page 32 Appendix C i-3 Control Technology Spare Parts For an i-3 Control Technology replacement parts list, please refer to i-3 P1 deadfront kit label, P/N: 15-A-1047-01 which is located on the inside of the panel deadfront.
- Page 33 Siemens Energy & Automation, Inc. 3333 Old Milton Parkway Alpharetta, GA 30005 For Technical Support: Call us at 1.800.427.2256 or visit www.sea.siemens.com/power For Nearest Sales Office: Call us at 1.800.964.4114 or visit www.sea.siemens.com/sales/salesoffices.html Warranty Support and Customer Service: Contact local sales office.
- Page 34 ˆ2007 Siemens Energy & Automation, Inc. All Rights Reserved. Siemens is a registered trademark of Siemens AG. Product names mentioned may be trademarks or registered trademarks of their respective companies. Specifications are subject to change without notice. PBSA-I3CON-0207 New .4M0207MW Printed in USA...