Table of Contents
Advertisement
Quick Links
LAUNCH
Table of contents
1. Precaution......................................................1
2. Structure and working Principle...................2
2.1 Structure Schematic Diagram...............................2
3 Tools for installation and adjustment..................4
4. Unpacking....................................................4
5. Installation....................................................4
5.1 Important notice..........................................4
5.2 Installation Procedure.......................................4
5.2.1 Selecting installation site .................................4
5.2.2 Base plate layout.............................................5
5.2.3 Install the powerside column...............................5
5.2.4 Install the floor plate...........................................6
Installation Instruction for Economical Symmetric Floor-plate 2-post Lift
5.2.5 Install the offside column....................................6
5.2.7 Install the power unit.........................................7
5.2.8 Connecting the power supply..............................7
5.2.9 Connecting the hydraulic lines..............................8
5.2.10 Install the swing arm and guardrail.......................9
5.2.11 Adjust the steel chain.......................................6
5.2.12 Install the floor plate cover..............................9
6. Lift Adjustment...............................................10
6.1 Preparation before adjustment........................10
6.2 Adjustment procedure.......................................10
7. List of the lift components...........................11
Diagram of the hydraulic system TLT235/TLT240SB...17
i
Advertisement
Table of Contents
Related Manuals for Launch TLT235SB
Summary of Contents for Launch TLT235SB
-
Page 1: Table Of Contents
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift 5.2.5 Install the offside column………………………………6 Table of contents 5.2.6 Install and adjust the balancing steel cables………7 1. Precaution………………………………………………1 5.2.7 Install the power unit………………….…..………..…7 2. Structure and working Principle.………………2 5.2.8 Connecting the power supply…………………………7 2.1 Structure Schematic Diagram…….……………………2... -
Page 2: Precaution
The manufacturer reserves the right to make design changes or add improvements to its product line without notice. Before installation, carefully check the packing list of lift. In case of any question, please contact the distributor or LAUNCH immediately. -
Page 3: Structure And Working Principle
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Structure schematic diagram 2. Structure and working TLT235SB（TLT240SB） the Floor-plate two-post lift principles structure is shown below (Figure 1, Figure2): 2750 OFFSIDE COLUMN POWERSIDE COLUMN START BUTTON LOWERING HANDLE POWER UNIT... -
Page 4: Main Structure And Principle Of The Equipment
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Passing width 2486 2586 3370 Figure 2 to adapt to different heights of vehicle chassis. Balancing mechanism: To keep the balance Main structure and principle during the lifting and lowering process, the lift... -
Page 5: Tools For Installation And Adjustment
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift the safety locking plate goes up against on the 5. Installation toothed bar plate by the tension of spring. When the carriage stops, the safety locking plate opens and then is engaged in the toothed bar slot to ensure the carriage will not go down;... -
Page 6: Base Plate Layout
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift If the thickness of the whole ground concrete is less The front and back of the lift should be reserved with than 250mm, the concrete slab must be made. The sufficient space to accommodate all the vehicles. -
Page 7: Install The Floor Plate
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Guided by the hole on the base plate of the column, drill the 5.2.3 Install the powerside column holes into the concrete slab and use five concrete anchor bolts to fix it onto the ground. During the drilling process, First raise the powerside column upper right to the location. -
Page 8: Install And Adjust The Balancing Steel Cables
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift falling of the column. Raise the two carriages to the safety locking position The wire protective pipe on the floor plate must (make sure that the safety locks on each column are... -
Page 9: Connecting The Power Supply
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift 5.2.8 Connecting the power supply（As Figure 7） Dismantle the sealing cover of the electrical box on the power unit and do the wiring according to the circuit diagram; the power supply switch is required to be installed near the lift for convenient disconnecting the power supply during maintenance or in case of emergency. -
Page 10: Install The Swing Arm And Guardrail
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift 5.2.10 Install the swing arm and guardrail Install the swing arm, guardrail and door rubber pad as shown in Fig. 9. Note ： During the installation, lubricate the moving parts of... -
Page 11: Lift Adjustment
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Press the starting button on the motor, and the 6. Lift adjustment carriage rises; stop pressing the button, then the carriage will stop. In order to lower down the carriage, first pull the steel rope for the safety locks on the two 6.1 Preparation before the... -
Page 12: List Of The Lift Components
Our company will not be LAUNCH and its sales agents based on the liable for other uses. In case of damages to the corresponding material code No in the list... - Page 13 LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift...
- Page 14 LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift...
- Page 15 LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Material coding No Name TLT235SB Powerside column 11MC126D TLT240SB Powerside column 11MC124D TLT235SB Offside column 11MC127C TLT240SB Offside column 11MC125C Floor plate 11MC045C Floor plate cover 11MC044C Top plate assembly 11MC544A...
- Page 16 LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Sheave 11BC098B Sheave axle 11BC102B Steel chain 10AJ069A Pin 2×26 11AG010A Chain threaded end 11BC099C Nut M16 11AC083A Carriage 11MC117C Sliding block 11AC120A Rubber pad on arm 12AE609A Screw M5X8 11AB661A...
-
Page 17: Diagram Of The Electrical System Tlt235/Tlt240Sb
LAUNCH Installation Instruction for Economical Symmetric Floor-plate 2-post Lift Diagram of electrical system for Single-phase motor Diagram of hydraulic system AC500V,20A switch prepared by user KM-AC Contactor； M-Motor；SB-Start button Diagram of electrical system for three-phase motor 1-Gear pump, 2-motor, 3-oil filter, 4-check valve, 5-safety valve,6-manual lowering valve 7-Sevo flow –...
Need help?
Do you have a question about the TLT235SB and is the answer not in the manual?
Questions and answers