Panasonic SC-HC05 Owner's Manual

Owner's Manual
Compact Stereo System
Model No.
Dear Customer
Supplied Accessories Thank you for purchasing this system.
For optimum performance and safety, read these
Check and identify the supplied accessories.
instructions fully before you connect, operate or adjust
Use numbers indicated in parentheses when asking for
this system.
replacement parts. (Product numbers correct as of January
2011. This may be subject to change.)
Keep this manual for future reference.
To order accessories, refer to "Accessory Purchases
Your system and the illustrations can look differently.
(United States and Puerto Rico)" on the next page.
1 x AC power supply cord
If you have any questions contact
1-800-211-PANA (7262)
(K2CB2CB00021)
The warranty can be found on the next page.
1 x Remote control
(RAK-SC989ZM)
1 x Lithium Button-Type battery
As an ENERGY STAR
(Battery is already installed in the remote control.)
Panasonic has determined
that this product meets the
ENERGY STAR
energy efficiency.
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
© Panasonic Corporation 2011
Printed in China
IMPORTANT SAFETY INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety
instructions listed below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they
exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
SC-HC05
MODEL NUMBER
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SERIAL NUMBER
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
User memo:
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
DATE OF PURCHASE
DEALER NAME
The lightning flash with arrowhead symbol,
DEALER ADDRESS
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
TELEPHONE NUMBER
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
Product identification marking is located on the bottom of unit.
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance. The unit should be installed near an accessible AC power
outlet, with the power cord connected directly to it.
To completely disconnect power from the unit, unplug the
power cord from the AC power outlet.
FCC Note: CAUTION!
This equipment has been tested and found to comply with the
DO NOT INSTALL OR PLACE THIS UNIT IN A
limits for a Class B digital device, pursuant to Part 15 of the
BOOKCASE, BUILT-IN CABINET OR IN ANOTHER
FCC Rules.
CONFINED SPACE. ENSURE THE UNIT IS WELL
These limits are designed to provide reasonable protection
VENTILATED. TO PREVENT RISK OF ELECTRIC
against harmful interference in a residential installation. This
SHOCK OR FIRE HAZARD DUE TO OVERHEATING,
equipment generates, uses and can radiate radio frequency
ENSURE THAT CURTAINS AND ANY OTHER
energy and, if not installed and used in accordance with
MATERIALS DO NOT OBSTRUCT THE VENTILATION
the instructions, may cause harmful interference to radio
VENTS.
communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
WARNING:
SC-HC05 determined by turning the equipment off and on, the user is
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
encouraged to try to correct the interference by one or more of
OR PRODUCT DAMAGE,
the following measures:
DO NOT EXPOSE THIS APPARATUS TO RAIN,
•
• Reorient or relocate the receiving antenna.
MOISTURE, DRIPPING OR SPLASHING AND THAT
• Increase the separation between the equipment and receiver.
NO OBJECTS FILLED WITH LIQUIDS, SUCH AS
• Connect the equipment into an outlet on a circuit different
VASES, SHALL BE PLACED ON THE APPARATUS.
from that to which the receiver is connected.
• USE ONLY THE RECOMMENDED ACCESSORIES.
• Consult the dealer or an experienced radio/TV technician for
DO NOT REMOVE THE COVER (OR BACK); THERE
•
help.
ARE NO USER SERVICEABLE PARTS INSIDE.
FCC caution: To maintain compliance with FCC regulations,
REFER SERVICING TO QUALIFIED SERVICE
shielded interface cables must be used with this equipment.
PERSONNEL.
Operation with non-approved equipment or unshielded cables
may result in interference to radio and TV reception. Any
changes or modifications not approved by the party responsible
for compliance could void the user's authority to operate this CAUTION!
equipment.
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
This device complies with Part 15 of the FCC Rules.
manufacturer. Dispose of used batteries according to the
Operation is subject to the following two conditions:
manufacturer's instructions.
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Responsible Party:
WARNING
Panasonic Corporation of North America
Risk of fire, explosion and burns. Do not disassemble, heat
One Panasonic Way
above 60°C (140°F) or incinerate.
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
WARNING
Telephone No.: 1-800-211-PANA (7262)
Keep the Button-Type battery out of reach of children to
prevent swallowing.
WARNING:
To satisfy FCC RF exposure requirements for mobile
– If you see this symbol –
transmitting devices, a separation of 20 cm or more should be
maintained between the antenna of this device and persons
Information on Disposal in other Countries outside the
® Partner,
during device operation. To ensure compliance, operations at
European Union
closer than this distance are not recommended. The antenna
used for this transmitter must not be co-located in conjunction
® guidelines for
with any other antenna or transmitter.
P En Sp
< For USA-California only >
This product contains a CR Coin Cell Lithium Battery which
"Made for iPod" and "Made for iPhone" mean that an electronic
contains Perchlorate Material - special handling may apply.
accessory has been designed to connect specifically to
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
iPod, or iPhone, respectively, and has been certified by the
RQTX1316-2P
developer to meet Apple performance standards.
L0111HH2031
The Bluetooth
Apple is not responsible for the operation of this device or its
Bluetooth SIG, Inc. and any use of such marks by Panasonic
compliance with safety and regulatory standards.
Corporation is under license. Other trademarks and trade
names are those of their respective owners.
Please note that the use of this accessory with iPod, or iPhone
may affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are
trademarks of Apple Inc., registered in the U.S. and other
countries.
Product service
1. Damage requiring service — The unit should be serviced 3. Replacement parts — When parts need replacing ensure
by qualified service personnel if:
the servicer uses parts specified by the manufacturer or
(a) The AC power supply cord or the plug has been
parts that have the same characteristics as the original
damaged; or
parts. Unauthorized substitutes may result in fire, electric
(b) Objects or liquids have gotten into the unit; or
shock, or other hazards.
(c) The unit has been exposed to rain; or
(d) The unit does not operate normally or exhibits a marked
4. Safety check — After repairs or service, ask the servicer
change in performance; or
to perform safety checks to confirm that the unit is in proper
(e) The unit has been dropped or the cabinet damaged. working condition.
2. Servicing — Do not attempt to service the unit beyond that Product information
described in these operating instructions. Refer all other
For product information or assistance with product operation:
servicing to authorized servicing personnel.
Refer to "Customer Services Directory (United States and
Puerto Rico)".
Specifications
Amplifier section Bluetooth
RMS output power stereo mode
Bluetooth
Front Ch (both ch driven)
Wireless equipment classification
20 W per channel (6 ), 1 kHz, 10% THD
Support profiles
Total RMS stereo mode power 40 W Frequency band
FTC output power stereo mode
2402 MHz to 2480 MHz (Adaptive Frequency Hopping)
Front Ch (both ch driven)
Driving distance
15 W per channel (6 ), 20 Hz to 20 kHz, 10% THD
Total FTC stereo mode power 30 W
General
Terminal section
Power supply
AUX (rear)
Power consumption
") jack
Terminal Stereo, 3.5 mm ( 1 /
Dimensions (W x H x D)
8
Speaker section
Type 2 way, 2 speaker system (passive radiator)
Mass (Weight)
Speaker unit(s)
Operating temperature range
") cone type x 1/ch
Woofer 6.5 cm (2 1 /
2
") piezo type x 1/ch
Tweeter 1.5 cm ( 5 /
8
Operating humidity range
Passive radiators 8 cm (3 1 / ") x 2/ch
8
Impedance 6
Power consumption in standby mode
Note:
1. Specifications are subject to change without notice.
Mass and dimensions are approximate.
2. Total harmonic distortion is measured by the digital
spectrum analyzer.
Getting started
Remote control
Before using
Remove the insulation sheet before you use the remote
control for the first time.
Insulation sheet
Replacing the battery
Replace the remote control battery when it stops operating
or when the range is decreased. Replace with a new battery
(CR2025) only.
Battery holder
Stopper
1
While pressing the stopper, pull out the battery
holder.
2
Insert a new battery with the (+) side facing up.
3
Push the battery holder back fully.
CAUTION!
• Insert with poles aligned.
• Do not touch the terminals (+ and –) with metal objects.
• Do not recharge, disassemble, remodel, heat or throw into
fire.
• Keep out of reach of children.
• Do not heat or expose to flame.
• Do not leave the battery(ies) in an automobile exposed
to direct sunlight for a long period of time with doors and
windows closed.
This symbol is only valid in the European Union. • Remove the battery if you do not use the remote control for
If you wish to discard this product, please a long period of time. Keep in a cool, dark area.
contact your local authorities or dealer and ask
for the correct method of disposal. If any electrolyte should come into contact with your hands or
clothes, wash it off thoroughly with water.
If any electrolyte should come into contact with your eyes,
never rub the eyes.
Rinse eyes thoroughly with water, and then consult a doctor.
Overview of controls
® word mark and logos are owned by the
iPod MENU
OK
SELECTOR LINK MODE
MUTE
PAIRING
A Standby/on switch [`], [1, POWER]
Press to switch the unit from on to standby mode or vice
versa.
In standby mode, the unit is still consuming a small
amount of power.
B
View the iPod or iPhone menu
C Select an item
D Confirm a selection
Set or cancel the auto off function
E ®
Select iPod, Internet radio, Bluetooth or AUX mode
Bluetooth ® is the default mode except when an iPod or
® section
iPhone is connected.
®
system specification Ver. 2.1 + EDR
F ®
Class 2 (2.5 mW) Start Bluetooth pairing mode
Select Bluetooth ® link mode
A2DP, AVRCP
Adjust the audio input level in AUX mode
G
Adjust the volume of the system
10 m (33 ft) line of sight
The setting returns to the default when you disconnect the
(iPhone 4, at height 1 m (3.3 ft), in MODE 1)
AC power supply cord.
H
Mute the sound of the system
In iPod mode : The light blue and green status
AC 120 V, 60 Hz
indicators blink alternately.
16 W
In Bluetooth ® mode : The light blue and blue status
370 mm x 176 mm x 85 mm
indicators blink alternately.
" x 7" x 3 ")
(14 1 / 1 /
In AUX mode : The light blue status indicator blinks
2 2
[D = 121 mm (4 3 / ") dock open] continuously.
4
1 ") without stand] This function does not work when the system is pairing or
[D = 59 mm (2 /
2
waiting to connect with a Bluetooth ® device.
1.8 kg (9 lb.)
Press the button again to cancel.
0°C to +40°C
Mute is also canceled when you adjust the volume or
(+32°F to +104°F)
when you switch off the system.
35% to 80% RH (no condensation)
Maintenance
0.1 W (approximate)
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this system.
• Before using chemically treated cloth, read the instructions that came with the cloth carefully.
Using an iPod or iPhone
Connect the AC power supply cord Connecting an iPod or iPhone
Preparation
Rear view
Update your iPod or iPhone with the latest software.
Make sure to remove the iPod or iPhone from its case.
1
Push [x, iPod] to open the dock.
To household AC outlet
• Use the included AC power supply cord with this system
only.
• Do not use an AC power supply cord from other equipment.
Conserving power
The system consumes approximately 0.1 W when it is in
standby mode. Disconnect the power supply if you do not use
the system. Some settings will be lost after you disconnect the
system. You have to set them again.
2
Insert a compatible dock adapter.
Speakers
3
Connect the iPod or iPhone.
• Do not remove the speaker nets.
The status indicator changes to green.
• These speakers do not have magnetic shielding. Do not put
them near TVs, PCs or other devices easily influenced by
iPhone
magnetism.
(not included)
• When you play at high levels for a long period, it can cause
damage to the system and decrease the life of the system.
• Decrease the volume when you play distorted sound to
prevent damage.
Hold the dock when connecting or disconnecting the iPod
or iPhone.
To close the dock
1
Disconnect the iPod or iPhone.
2
Press [PUSH CLOSE] while closing the dock.
Top view
Note:
• Make sure to align your iPod or iPhone with the connector
when inserting.
• Make sure to press [PUSH CLOSE] while closing the dock to
prevent damage.
• When an iPod or iPhone is connected, press [SELECTOR]
to switch between modes (Internet radio, Bluetooth
iPod).
• The system automatically switches on when you connect an
iPod or iPhone that is in playback mode (except for some
models).
• To purchase a dock adapter, consult your local iPod or
iPhone dealer.
I Start or pause playback Listening to the Internet radio
J Skip or search track
K You can listen to a radio station on the Internet if you install
Power indicator
the "vTuner for Panasonic" application on your iPod touch or
On : The system is on
iPhone. Download this application from the App Store.
Off : The system is in standby mode
Note:
L
iPod or iPhone dock
For compatible iPod touch and iPhone models and
instructions on how to use the "vTuner for Panasonic"
M
Status indicator application, refer to:
Green : iPod mode http://radio.vtuner.com/panasonic/en/
Blue : Bluetooth ® mode
Light blue : Set or cancel the auto off function
Mute function is on
Off : AUX mode
The green status indicator blinks each time a remote
control button is pressed.
Using the auto off function
N
[PUSH CLOSE]
Press while closing the dock.
O Remote control sensor
The system automatically switches off if there is no audio input
Point the remote control at the remote control sensor,
and you do not use it for approximately 30 minutes.
away from obstacles, at a maximum range of 7 m (23 ft)
1
directly in front of the main unit.
Press [SELECTOR] to select AUX mode.
Status indicator: Off
2
Press and hold [OK].
ON ↔ OFF
(default)
ON : The light blue status indicator blinks 2 times.
OFF : The light blue status indicator blinks 1 time.
Basic playback
1
Connect the iPod or iPhone.
2
Press [4/9] to start playback.
Pause playback Press [4/9].
Press again to continue playback.
Skip track Press [2] or [6].
Search track Press and hold [2] or [6].
View the iPod or Press [iPod MENU].
iPhone menu
Select an item
Press [R] or [T] and then press
[OK].
Note:
• Depending on the model, it may be necessary to remove the
iPod or iPhone and select the album, artist, etc. on the iPod
or iPhone.
• Operation results may vary depending on the iPod or iPhone
models.
• Read the User Guide of the iPod or iPhone for operating
instructions.
Compatible iPod and iPhone
(as of January 2011)
• iPod touch 4th generation (8GB, 32GB, 64GB)
• iPod nano 6th generation (8GB, 16GB)
Dock adapter • iPod touch 3rd generation (32GB, 64GB)
(not included)
• iPod nano 5th generation (video camera) (8GB, 16GB)
• iPod touch 2nd generation (8GB, 16GB, 32GB)
• iPod classic [120GB, 160GB (2009)]
• iPod nano 4th generation (video) (8GB, 16GB)
• iPod classic (160GB) (2007)
• iPod touch 1st generation (8GB, 16GB, 32GB)
• iPod nano 3rd generation (video) (4GB, 8GB)
• iPod classic (80GB)
• iPod nano 2nd generation (aluminum) (2GB, 4GB, 8GB)
• iPod 5th generation (video) (60GB, 80GB)
Connector • iPod 5th generation (video) (30GB)
• iPod nano 1st generation (1GB, 2GB, 4GB)
• iPhone 4 (16GB, 32GB)
• iPhone 3GS (8GB, 16GB, 32GB)
• iPhone 3G (8GB, 16GB)
• iPhone (4GB, 8GB, 16GB)
Compatibility depends on the software version of your iPod or
iPhone.
Note:
• The display on the iPod can show differently because of the
compatibility of the iPod models.
• All phone features can only be controlled by the touch
screen of the iPhone.
• The system does not show incoming calls or the phone
status.
• Playback will stop when there is an incoming call.
Disconnect the iPhone to answer the call.
• A call is not canceled when you connect or disconnect the
iPhone from the system.
• There is no Apple Inc. specification that will guarantee the
above iPhone response. iPhone responses can be different
on newer models or with newer software.
Charging an iPod or iPhone
® , AUX or
An iPod or iPhone is charged automatically when connected
to the system (even when the system is in standby mode).
• See the iPod or iPhone display for its battery charging
status.
• Disconnect the iPod or iPhone if it is not used for an
extended period of time after charging is complete.
• Charging stops when the battery is fully charged. The battery
will deplete naturally.
Preparation
Install "vTuner for Panasonic" on your iPod touch or iPhone.
Connect your iPod touch or iPhone to the Internet. Go to the
Home screen of the iPod touch or iPhone.
1
Connect the iPod touch or iPhone.
2
Press [SELECTOR] to start the application.
Note:
• This function does not work when a Bluetooth ® device is
connected.
• 1 minute before the system switches off, the power indicator
blinks.
• The setting returns to the default when you disconnect the
AC power supply cord.