1. Precautions 1. Precautions 1-1. Safety Precautions Follow these safety, servicing, and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1-1. Warnings For continued safety, do not attempt to modify any circuitry. 1-1-2. Servicing the LCD TV When servicing the LCD TV, Disconnect the AC line cord from the AC outlet.
1. Precautions 1-2. Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
1. Precautions 1-4. Installation Precautions For safety reasons, more than two people are required for carrying the product. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal temperature may cause fire.
2. Product specifications 2. Product specifications 2-1. Feature & Specifications Model UE32B6000VW Feature Digital-TV, RF, 4-HDMI, 1-Component, 1-AV, USB1, D-SUB, 1Ext � Brightness : 500cd/m � Contrast Ratio : 3000000:1 � Response time :3ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, 3, 4, Component1, PC Mode and Sub picture is available in TV analog and digital mode) �...
Page 9
2. Product specifications Model UE40B6000VW Feature Digital-TV, RF, 4-HDMI, 1-Component, 1-AV, USB1, D-SUB, 1Ext � Brightness : 500cd/m � Contrast Ratio : 3000000:1 � Response time :3ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, 3, 4, Component1, PC Mode and Sub picture is available in TV analog and digital mode) �...
Page 10
2. Product specifications Model UE46B6000VW Feature Digital-TV, RF, 4-HDMI, 1-Component, 1-AV, USB1, D-SUB, 1Ext � Brightness : 500cd/m � Contrast Ratio : 3000000:1 � Response time : 3ms � Dynamic contrast, Super-PVA � PIP(in HDMI 1, 2, 3, 4, Component1, PC Mode and Sub picture is available in TV analog and digital mode) �...
Page 11
2. Product specifications PAL On-Air Channel Frequence Table Europe INDONESIA IRELAND South Africa ANGOLA NEWZEALAND ITALY channel PAL-BG PAL-BG PAL-I PAL-I PAL-I PAL-BG PAL-BG 53.75 62.25 82.25 175.25 183.75 192.25 201.25 210.25 217.25 224.25 44.25 45.75 43.25 45.25 48.25 55.25 53.75 52.25 55.25...
Compatibility problem. Before connecting your device to the TV, please back up your files to prevent them from damage or loss of data.SAMSUNG is not responsible for any data file damage or data loss. Do not disconnect the USB device while it is loading.
Page 17
2. Product specifications -. movie format File Extention Container Video Decoder Resolution Audio codec Divx 3.11/4.x/5.1/6.0 720 x 576 XviD 1920 x 1080 *.avi H.264 BP/MP/HP 1920 x 1080 LPCM MPEG4 SP/ASP 1920 x 1080 ADPCM Motion JPEG 800 x 600 Divx 3.11/4.x/5.1/6.0 720 x 576 XviD...
2. Product specifications 2-4. Spec Comparison to the Old Models UB7W SAPPHIRE Model (UE40B6000VW/UE46B6000VW) (LE46A856S1F/LE52A856S1F) Design Display Type LCD TV LCD TV Resolution 1920 x 1080 1920 x 1080 LCD Panel TFT LCD Panel 120Hz TFT LCD Panel 120Hz Screen Size 40”...
3. Disassembly and Reassemble 3. Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the UE40B6000VW LCD TV. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1. Disassembly and Reassembly Cautions: 1.
Page 22
3. Disassembly and Reassemble Description Picture Description Screws 2. Remove the screws of rear-cover. 40” 46” 2-1. Pull out a AC Power Cord 3. Lift up the rear-cover.
Page 23
3. Disassembly and Reassemble Description Picture Description Screws 4. Remove the cables and screws from 40” SMPS, Main board and Woofer and Bracket stand link. 46” Woofer x 2...
Page 24
3. Disassembly and Reassemble Description Picture Description Screws 5. Remove the panel bracket screws from the panel. Reassembly procedures are in the reverse order of disassembly procedures. ※...
4. Troubleshooting 4. Troubleshooting 4-1. Troubleshooting Check the various cable connections first. • Check to see if there is a burnt or damaged cable. • Check to see if there is a disconnected or loose cable connection. • Check to see if the cables are connected according to the connection diagram. Check the power input to the Main Board.
Page 26
4. Troubleshooting Simple flow chart of malfunction Does the TV turn on? Can you see anything on the screen? Can you see OSD menu running on the screen? Can you see Digital Channel broadcast ? Check LVDS cable connected Check the Power Cord to Main Board.
Page 28
The WLAN does not work. An explanation of Equipment other than the WLAN USB stick supplied by Samsung Electronics (as a bundle) will not work. Media play The sharer must support IEEE 801.11 g/b. IEEE 801.11 n is supported.
Page 29
The DLNA server that I could see on the PC Share Manager 1.Check if the PC is turned off. 2. Check if the Samsung TV has suddenly disappeared. What Search TV is set to reject connections in the access control menu should I do? of the Samsung PC Share Manager.
Page 30
4. Troubleshooting I cannot play files with the wmv or flv DLNA Video Play The video play function is not supported for files with these extension. extensions. I cannot use the 20 second Seek DLNA Video Play To use the Seek function while playing at 2x Fast Forward, function while playing at 2x Fast press the Play button to first make the playing speed Forward.
Page 31
Images provided by Samsung.com or a 3rd party content personal photos using the Gallery Content Library provider linked to Samsung.com will not be played in the function. How can I do this? [Contents Library]. However, you can use the SlideShow function of WiseLink Pro.
Page 32
4. Troubleshooting 4-1-1. No Power The PD board relay does not work when connecting the power cord. Symptom The units appears to be dead. The PD relay does not work when connecting the power cord if the cables are improperly connected or the Main Board or PD is not functioning.
Page 34
4. Troubleshooting 4-1-2. No Video (Analog PC signal) Symptom Audio is normal but no picture is displayed on the screen. Check the PC source Major Check the IC7001(chelsea) checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the IP board.
Page 35
4. Troubleshooting WAVEFORMS PC Input (V-Sync, H-Sync) LVDS Out (CLK + / -) 4-11...
Page 36
4. Troubleshooting 4-1-3. No Video (HDMI - Digital Signal) Symptom Audio is normal but no picture is displayed on the screen. Check the HDMI source Major Check the IC7001(chelsea) checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the IP board.
Page 37
4. Troubleshooting WAVEFORMS HDMI Input (CLK + / -) Tuner CVBS Out (Pattern: Grey Bar) TS DATA Out (Clk, Data [0]) 4-13...
Page 38
4. Troubleshooting 4-1-4. No Video (Tuner_CVBS) Symptom Audio is normal but no picture is displayed on the screen. Check the Tuner CVBS source Major Check the Chelsea checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the IP board.
Page 39
4. Troubleshooting WAVEFORMS Tuner CVBS Out (Pattern: Grey Bar) Eagle+ Out (Clk, H-Sync) 4-15...
Page 40
4. Troubleshooting 4-1-5. No Video (Tuner DTV) Symptom Audio is normal but no picture is displayed on the screen. Check the DTV source Major Check the Chelsea checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the PD board.
Page 41
4. Troubleshooting WAVEFORMS Tuner CVBS Out (Pattern: Grey Bar) TS DATA Out (Clk, Data [0]) 4-17...
Page 42
4. Troubleshooting 4-1-6. No Video (Video CVBS 1) Symptom Audio is normal but no picture is displayed on the screen. Check the Video CVBS source Major Check the Chelsea checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the PD board.
Page 44
4. Troubleshooting 4-1-7. No Video (Component 1) Symptom Audio is normal but no picture is displayed on the screen. Check the Component source Major Check the Chelsea checkpoints This may happen when the LVDS cable connecting the Main Board and the Panel is disconnected. Caution Make sure to disconnect the power before working on the PD board.
Page 46
4. Troubleshooting 4-1-8. No Sound Symptom Video is normal but there is no sound. When the speaker connectors are disconnected or damaged. Major When the sound processing part of the Main Board is not functioning. checkpoints Speaker defect.. Caution Make sure to disconnect the power before working on the PD board. No sound Check the sound source and Input a sound signal.
Page 48
4. Troubleshooting 4-1-10. Reference Output CNT which run Edge Led (Is unrelated even if right and left changes) When you see the screen in front of TV, If the left side (a) has a problem, Connect 2, cable at the 1 position, in case of normal picture, change LED panel.
Page 49
4. Troubleshooting Connecting a PC Using the D-sub cable Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer Connect a PC Audio Cable between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.
4. Troubleshooting 4-2. Alignments and Adjustments 4-2-1. General Alignment instruction Usually, a color LCD-TV needs only slight touch-up adjustment upon installation. Check the basic characteristics such as height, horizontal and vertical sync. Use the specified test equipment or its equivalent. Correct impedance matching is essential.
4. Troubleshooting 4-3. Factory Mode Adjustments 4-3-1 Entering Factory Mode To enter ‘Service Mode’ Press the remote -control keys in this sequence : - If you do not have Factory remote - control Power OFF INFO MENU MUTE Power On 4-3-2 How to Access Service Mode Using the Customer Remote Turn the power off and set to stand-by mode...
Page 52
4. Troubleshooting 4-3-3 Factory Data Option Main: Opiton, Mode : CDTV, RES :480I Factory Reset Option Type 46A1UF0E Model UB7000 TUNER ALPS Region PANEURO Light Effect Media Link Type Infolink ON PDP GROUP … ADC/WB AV Calibration Success Comp Calibration Success PC Calibration...
Page 53
4. Troubleshooting ADC Result 1st_Y_GH 1st_Y_GL 1st_Cb_BH 1st_Cb_BL 1st_Cr_RH 1st_Cr_RL 2nd_R_L 2nd_G_L 2nd_B_L 2nd_R_H 2nd_G_H 2nd_B_H White Balance Sub Brightness R-Offset G-Offset B-Offset Sub Contrast R-Gain G-Gain B-Gain Movie R-Offset … Movie B-Offset … Movie R-Gain … Movie B-Gain … 4-29...
Page 54
4. Troubleshooting Contol EDID EDID ON/OFF EDID WRITE ALL Success EDID WRITE PC Success EDID WRITE HDMI Success EDID WRITE HDMI1 EDID WRITE HDMI2 EDID WRITE HDMI3 EDID WRITE HDMI4 EDID 1.2 PORT None Sub Option RF Mute Time 600ms TOOLS Support ND ADJ Support...
Page 55
4. Troubleshooting Sound SAP High Threshold 0x1ah Pilot Level Low Thld 0x10h SAP Low Threshold 0x9h A2 Pilot AM Carr High Thld … Speaker Delay Normal 0x59h A2 Pilot AM Carr Low Thld … Auxout Delay Normal 0x59h NICAM Error High Thld …...
Page 56
4. Troubleshooting Expert N/D ADJ Expert Source … Advanced (Press the 0 button four times on advanced to enters hidden menu) BM_slope1 Skin-Enable FBE3 BM_slope2 Skin-UV BM_slope3 FBE Sub color BM_slope4 M-Skin-UV … BM_start M-Sub Color … BM_start_max Lfunc_basis Hfunc_basis Mean-Offset1...
Page 57
4. Troubleshooting Standard Contrast EPA Standard Standard Brightness Standard Sharpness Standard Color Standard Tint Standard Backlight CH_VDEC AGC_mode CTI_level Gain_VCR ST_Beg_NTSC Y_Gain_Man VS_Slice_Level Saturation HS_Slice_Level FB_Delay_adj Y_Shape_sel RGB_Delay_adj Y_Shape_SCM h_pk_gain C_Shape_sel v_pk_gain C_Shape_SCM h_pk_band If_iir 2d_pk_gain If_filt_sel 2d_pk_band LTI_en slice_mod_fine LTI_level scm_fdet_lvl CTI_en...
4. Troubleshooting 4-4. White Balance - Calibration 4-4-1 White Balance -Calibration ADC/WB AV Calibration Comp Calibration PC Calibration HDMI Calibration 4-4-2 Service Adjustment - You must perform Calibration in the Lattice Pattern before adjusting the White Balance. Color Calibration Adjust spec.
Page 62
4. Troubleshooting Method of Color Calibration (AV) 1) Apply the NTSC Lattice (N0.2) pattern signal to the AV IN 1 port 2) Press the Source key to switch to “AV1” mode 3) Enter Service mode 4) Select the “ADC/WB” and “ADB” menu 5) Select the “AV Calibration”...
4-5. Servicing Information 4-5-1 Upgrading the Software Samsung may offer upgrades for TV’s firmware in the future. Please contact the Samsung call center at 1-800- SAMSUNG (726-7864) to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on your TV.
Page 64
1) The message “Does the problem still exist with this test pattern?” is displayed. 2) Press “Yes”. This is a TV SET problem. The massage “Contact Samsung’s call center at 1-800-SAMSUNG for assistance.” is displayed. 3) Press “No”. This is not a TV SET problem.
Page 65
1) The message “Does the problem still exist with this sound test?” is displayed. 2) Press “Yes”. This is a TV SET problem. The message “Contact Samsung’s call center at 1-800-SAMSUNG for assistance.”is displayed 3) Press “No”. This is not a TV SET problem.
6. Wiring Diagram 6-4. Connector Functions Connector Functions CNM802<->CN1001 Supply power from SMPS to Main Board. CN7005<->T-CON The LVDS signal transfered from Main Board to Panel. 6-5. Cables Main-SMPS Main-Tcon Function Assy 32” : BN39-01099Z(30P 300mm) 32” : BN39-01184D(51P 200mm) 32,40”...
Need help?
Do you have a question about the UE32B6000VW and is the answer not in the manual?
Questions and answers