Page 1
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
Koninklijke Philips Electronics N.V. or their respective owners. TP Vision Netherlands B.V. reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. PHILIPS and the PHILIPS’ Shield Emblem are used under license from Koninklijke Philips Electronics N.V.
1. Product information 1.1 Product Fiche 43PUS6401 • Energy Efficiency Class : A • Visible Screen Size : 108 cm / 43 inch • On Mode Power Consumption (W) : 67 W • Annual Energy Consumption (kWh) * : 98 kWh •...
Page 4
1.2 Power • Mains power : AC 220-240V +/-10% • Ambient temperature : 5°C to 35°C • Power saving features : Eco mode, Picture mute (for radio), Auto switch-off timer, Eco settings menu. 1.3 Operating System Android OS : Android Lollipop 5.1 1.4 Reception •...
Page 5
• 1280 x 768p - 60 Hz • 1360 x 765p - 60 Hz • 1360 x 768p - 60 Hz • 1280 x 1024p - 60 Hz • 1920 x 1080p - 60 Hz • 3840 x 2160p - 24 Hz, 25 Hz, 30 Hz, 50 Hz, 60 Hz 1.7 Connectivity TV Side •...
3.2 Assembly/Panel Removal( For 6432 series) 3.2.1 Rear Cover Warning: Disconnect the mains power cord before removing the rear cover. 1. Remove fixation screws [1] that secure the base assy, pull out the base assy from the set 2. Remove the fixation screws [2], [3] and [4] that secure the rear cover 3.
Page 11
3.2.2 AmbiLight Panel 1. Gently release the clamps and unplug the connectors [4] that secure the ambilight panels. Release the clips from the FFC connector that connect with the keyboard [5]. 2. Lift the AmbiLight panel from the rear cover. Make sure that wires and flat foils are not damaged while lifting the ambilight panel from the rear cover. Ambilight and Keyboard removal 3.2.3 Keyboard Control Unit Release the connectors [2] and [3] from the keyboard control panel.
Page 12
3.2.5 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 2. Remove all fixation screws from the PSU. 3.
3.2.8 WIFI module 1. Unplug the connector from the SSB.. 2. Remove fixation screw that secure the WIFI module, When defective, replace the whole unit. 3.2.9 LCD Panel 1. Remove the SSB as described earlier. 2. Remove the PSU as described earlier. 3.
Page 14
3.3.2 Stand 1.Remove the screws [1] that secure the black plastic and, gently remove the black plastic casing that covers the stand bracket 2. Remove the Allen screws [2] that secure the stand bracket and, pull out the stand downwards from the set, Stand removal[1] Stand removal[2]...
Page 15
3.3.3 Rear Cover 1. Remove the fixation screws [1,2,3] that secure the rear cover. 2. Unplug the connector [4] from SSB. Then lift the rear cover from the TV. Make sure that wires and flat foils are not damaged while lifting the rear cover from the set.
Page 16
3.3.4 AmbiLight Panel 1. Gently release the clamps and unplug the two connectors [5] that secure the ambilight panels. Release the clips from the FFC connector that connect with the keyboard [4]. 2. Lift the AmbiLight panel from the rear cover. Make sure that wires and flat foils are not damaged while lifting the ambilight panel from the rear cover. Ambilight and Keyboard removal 3.3.5 Keyboard Control Unit Release the connectors [2] and [3] from the keyboard control panel.
Page 17
3.3.7 Power Supply Unit (PSU) Caution: it is mandatory to remount all different screws at their original position during re-assembly. Failure to do so may result in damaging the PSU. 1. Gently unplug all connectors from the PSU. 5. Remove all fixation screws from the PSU. 3.
4. Service Modes 4.1 Service Modes The Service Mode feature is split into following parts: Service Alignment Mode (SAM). Factory Mode. Customer Service Mode (CSM).SAM and the Factory mode offer features, which can be used by the Service engineer to repair/align a TV set. ...
Page 19
With the “LEFT/RIGHT” keys, it is possible to: – (De) activate the selected menu item. – (De) activate the selected sub menu. – Change the value of the selected menu item. When you press the MENU button once while in top level SAM, the set will switch to the normal user menu (with the SAM mode still active in the ...
Page 20
Public Broadcasting Service password Reset. etc. How to Activate the Factory mode To activate the Factory mode, use the following method: Press the following key sequence on the remote control transmitter: from the “menu/home” press “1999”, directly followed by the “Back/Return”...
Page 21
After leaving the Customer Service Mode, the original settings are restored. Possibility to use “CH+” or “CH-” for channel surfing, or enter the specific channel number on the RC. How to Activate CSM To activate CSM, press the following key sequence on a standard remote control transmitter: “123654” (do not allow the display to time out between entries while keying the sequence).
5. Software Upgrading, Error code and Panel Code 5.1 Software Upgrading Step 1: Ready for F/W Upgrade 1. Rename the software as “autorun.upg” 2. Prepare a USB memory. 3. Copy the software to USB flash disk(root directory). Note the version of this F/W before you change the software file name. Step 2: F/W Upgrade 1.
Page 23
4. Press OK to start software upgrade 5. Upgrade in progress...
Page 24
Step 3: Check the SW version 1. After burning software, TV will restart 2. Press “Menu+1999+back”, enter Factory mode to check if the software version is correct Caution: Please make sure that software upgrade is finished before unplug the USB and AC power! 5.2 Error Code 5.2.1 Introduction Error codes are required to indicate failures in the TV set.
Page 25
5.2.3 Error codes overview In this chassis only “layer 2” error codes are available and point to problems on the SSB. They are triggered by LED blinking when CSM is activated. Only the following layer 2 errors are defined: 5.2.4 How to Clear the Error Buffer The error code buffer is cleared in the following cases: •...
Page 26
Press the following key sequence on a standard RC transmitter: “062598” directly followed by MENU and “xxx”, where “xxx” is a 3 digit decimal value of the panel type: see column “Display Code” in below tab. After resetting the Display Code, restart the set immediately. CTN_ALT BOM# Panel Type Display Code 43PUS6432/12 TPT430U3-EQYSHM.G S1J 43PUS7202/12 TPT430U3-EQYSHM.G S1J 49PUS6432/12 TPT490U2-EQYSHM.G SC1B...
6. Circuit Descriptions 6.1 Introduction The QM17.3E LA is a new chassis launched in Europe in 2017. The whole range is covered by MT5593U+ platform. The major deltas versus its predecessor support DVB-C; DVB-T/T2; DVB S2, with also USB3.0,WIFI/BT, multi-media, smart TV functionality The QM17.3E LA chassis comes with the following stylings: series xxPUS6432/xx ...
Page 28
Always replace a defective fuse with one with the correct specifications! This part is available in the regular market. Consult the Philips Service web portal for the order codes of the boards. Important delta’s with the platform are: •...
Page 29
- direct-view LED with 2D-dimming: PSDL power panel. PSL stands for Power Supply with integrated LED-drivers. PSLS stands for a Power Supply with integrated LED-drivers with added Scanning functionality (added microcontroller). PSDL stands for a Power Supply for Direct-view LED backlight with 2D-dimming. 6.3 DC/DC Converters The on-board DC/DC converters deliver the following voltages(depending on set execution): •...
Page 30
6.3.2 Power layout SSB Power SSB Top View...
Page 32
6.4 Front-End Analogue and DVB-T, DVB-C;ISDB-T reception 6.4.1 DVB-C part The Front-End for analogue tuner consist of the following key components: • TUNER EUROPE TDSY-G480D • TUNER EUROPE TDQS-A701F • SCALER MT5593UGIJ HSBGA-900 Processor Below find a block diagram of the front-end application for DVB-C part. 6.4.2 DTB-T2 part The Front-End for DVT part consist of the following key components: •...
Page 33
The following HDMI connector can be used: • HDMI 1: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC • HDMI 2: HDMI input ( TV digital interface support HDCP) with digital audio/PC DVI input/ARC • HDMI 3: HDMI input ( TV digital interface support HDMI1.4/HDCP1.3) with digital audio/PC DVI input/ARC •...
8.8 J 715G8009 IR/LED Panel 8-8-1 IR& LED &Light sensor S t a n d b y L E D Light Sensor 3V3SB CN201 LED_R DVD3V3 DVD3V3 C222 NC/ 1uF 10V RC-IR R201 R224 R223 I2C addr 100R 1/16W 5% C221 NC/ 100N 16V 3V3SB...
8.9 J 715G8010 IR/LED Panel 8-9-1 IR& LED &Light sensor S t a n d b y L E D Light Sensor CN201 3V3SB LED_R DVD3V3 DVD3V3 C222 NC/ 1uF 10V RC-IR R201 I2C addr R224 R223 100R 1/16W 5% C221 NC/ 100N 16V 3V3SB...
8.10 E 715G7088 Keyboard control panel 8-10-1 Key Joystick key define CONN TO SSB JOYSTICK Direction switch Key function Resistance Voltage Range Center 2-5 short Menu 0.0 to 0.22 V CN01 CN04 Right 1-5 short 0.5V 0.39 to 0.60 V KEY 1 AMBI_SPI_CLK Left...
Need help?
Do you have a question about the 43PUS6432/12 and is the answer not in the manual?
Questions and answers