Related Manuals for BRIO CLPOU520UVF2
Summary of Contents for BRIO CLPOU520UVF2
- Page 1 WATER DISPENSER MODEL NO. CLPOU520UVF2 Thank you for purchasing a Brio water cooler ® Please read and understand this manual before operating your water dispenser Retain this manual for future use...
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 INTENDED USE . -
Page 3: Safety Information
SAFETY INFORMATION WARNING: To reduce risk of injury and property damage, you must read this entire guide before assembling, installing and operating the dispenser . WARNING: This product dispenses water at very high temperatures . Failure to use properly can cause personal injury . -
Page 4: Intended Use
INTENDED USE This appliance is intended to be used in household and similar applications such as: • Staff kitchen areas in shops, offices and other working environments • Farm houses • Clients in hotels, motels and other residential type environments •... -
Page 5: Indicator Panel Description
Indicator Panel Description Power indicator light – When illuminated, indicates that the dispenser is on. Hot water indicator light – When illuminated, indicates that the dispenser is heating water. Cold water indicator light – When illuminated, indicates that the dispenser is cooling water. Filter indicator light –... -
Page 6: Installation
INSTALLATION 1 . Determine Installation Location Place the dispenser upright . Locate the dispenser on a hard and level surface in a cool shaded location near a grounded wall outlet . NOTICE: Do NOT plug in the power cord until the entire installation section is completed . -
Page 7: Flush The Filters
Gently tug on the tube (B) to ensure a secure connection with the feed water adapter (E) . 3 . Flush the Filters IMPORTANT: Follow this procedure every time you replace your filters. IMPORTANT: Ensure the water supply is off before you begin . Connect a filter (D) to the filter housing (C) by twisting the filter (D) clockwise. -
Page 8: Install The Filters And Complete The Installation
4 . Install the Filters and Complete the Installation After flushing, twist each filter (D) clockwise into the filter housings located inside the dispenser cabinet . The sediment filter goes on the left, the carbon filter on the right. Remove the safety plug from the water inlet hole on the back of the dispenser by pushing in the inlet hole collar and then gently pulling out the... -
Page 9: Operation
OPERATION IMPORTANT: This unit has been tested and sanitized prior to packing and shipping. During transit, dust and odors can accumulate in the tank and lines . Dispense and dispose at least one quart of water prior to drinking any water . Turn the Dispenser On/Off IMPORTANT: Before you activate the hot and cold switches, ensure water has filled the tanks... -
Page 10: Troubleshooting
TROUBLESHOOTING PROBLEM SOLUTION • It takes up to one hour after setup to dispense cold water . • Make sure the power cord is properly connected to a working outlet . The cold water is not • Make sure the back of the dispenser is at least 20 cm from a wall and there is free airflow on all 20 cm sides of the dispenser. -
Page 11: Clean The Dispenser
Clean the Dispenser CAUTION: Before cleaning, make sure the power switch is in the O (off) position and unplug the water dispenser . IMPORTANT: This dispenser contains UV technology that will help keep your dispenser clean . However, if you do need to clean your dispenser for any reason, follow these steps: Remove remaining water from reservoirs in the dispenser by dispensing from the hot and cold taps into a pitcher or bucket . -
Page 12: Filter Replacement Schedule
Filter Replacement Schedule FILTER TYPE REPLACEMENT SCHEDULE FUNCTION Reduces chlorine, taste and odor, lead Carbon 6 months or 950 gallons and cysts . Performs a coarse filtration of original Sediment 6 months or 950 gallons water . Removes mud, sand, iron, rust, and suspensions, and impurities . -
Page 13: Warranty
WARRANTY Brio (“Vendor”) warrants to the original purchaser of the Brio Water Coolers (the “Product”), and to no other person, that if the Product is assembled and operated in accordance with the printed instructions accompanying it, then for a period of one (1) year from the date of purchase, all parts in the Product shall be free from defects in material and workmanship . - Page 14 Contact Us Call: +1 844-257-4103 ©2019 DTWUSA...
Need help?
Do you have a question about the CLPOU520UVF2 and is the answer not in the manual?
Questions and answers
COLD WATER BEING DISPENSED IS NOT COLD
The cold water from the BRIO CLPOU520UVF2 may not be cold because:
1. The cooling system is not powered on. Ensure the cooling switch is flipped to the "On" position.
2. The unit has not been plugged in and turned on for at least 1 hour, which is the time needed for the water to become fully chilled.
3. The cooling light is still on, indicating the water has not yet reached the desired cold temperature.
4. There may be a power issue or a malfunction in the cooling system.
Check these factors to troubleshoot the issue.
This answer is automatically generated