Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trailer Valet RVR12
Summary of Contents for Trailer Valet RVR12
- Page 1 RVR12 OPERATING MANUAL...
-
Page 2: Table Of Contents
Failure to follow these guidelines may result in serious injury to persons and property for which Trailer Valet will not be held liable. Do not allow persons to operate or assemble this unit until they have read this manual and have developed a thorough understanding of how the unit works. -
Page 3: Important Safety Information
4. The RVR is designed for specific applications only. Trailer Valet will not be responsible for issues arising from modifications made onto the device. Do not modify the device or use the device for any application other than its intended purpose. -
Page 4: Thank You For Your Purchase & Warning
THANK YOU FOR YOUR PURCHASE Congratulations on your purchase of the Trailer Valet RVR12. For your future reference please complete the owner’s record below: Purchase Date: ______________________ Order No.:______________________ Retailer:_____________________________ Be sure to save your receipt and owner’s manual with warranty information in a safe place. -
Page 5: What's In The Box
Upon removing items from packaging, it is very important to thoroughly inspect all parts of the system before using the device. Any part that is missing or damaged must be immediately replaced. Contact Trailer Valet Customer Service at 1-844-846-9344 or Support@ TrailerValet.com RVR12 COMPONENTS... - Page 6 WHAT’S IN THE BOX SPARE PARTS Rotoclips Pins Links Treads Track Pin Tools Retainer Clip 4 Amp 10 Amp Tool Replacement Light Replacement Circuit Fuse Board Fuse COUPLER SET 2” or 2-5/16 Custom Hitch Ball Coupling Plate Custom Ball Rotation/ Base Tower Spanner Base...
-
Page 7: Attach With Coupler Set
Light CHARGING THE RVR12 1. Before charging your RVR12, be sure the radio and tug are both turned OFF. 2. The charging indicator light on the charger should light up red once the charger is connected properly. The tug will be fully charged once the charge indicator light turns green. -
Page 8: Controller Operation
CONTROLLER OPERATION Power Indicator LED Control Stick 3 Speed Toggle ON/OFF Switch Charging Indicator LED Charging Port Lanyard Anchor NOTE: The 3 Speed Toggle ranges from fast, moderate, and slow. When operating the valet at slow speeds it may be necessary to switch to the moderate or fast speed position on the toggle when turning at 90 degrees. -
Page 9: Operating Instructions
If you have any questions concerning the use of your Trailer Valet RVR on a slope or incline, please contact us at (844) 846- 9344 or email us at: support@trailervalet.com... -
Page 10: Tread Maintenance
TREAD MAINTENANCE ADJUSTING TRACK TENSION Over time, the tracks on your unit will stretch. This is expected after the first couple uses. To tighten your track, first, loosen the retaining bolt shown below using a 14 mm socket wrench. Only a half to quarter turn is needed to loosen the bolt. DO NOT attempt to remove the bolt. - Page 11 TREAD MAINTENANCE 3. Overlap the Track Links on each side of the track and insert the track pin and rotoclip as shown below. Apply pressure on end of pin when inserting the clip on the other end Track Pin and Rotoclip Insert Rotoclip into Retainer Clip Tool (Teeth pointing towards clip tool)
-
Page 12: Remote Charging & Batteries
REMOTE CHARGING & BATTERIES CHARGING THE REMOTE CONTROL WARNING: Only use the supplied charger to charge the remote control when using the supplied batteries or the following: - 1200mAh Ni-MH or Ni-Cd ‘AA’ Rechargeable Batteries The use of the remote charger with alkaline batteries installed can damage the remote control. - Page 13 REMOTE CHARGING & BATTERIES REPLACING THE REMOTE CONTROL BATTERIES 1. Remove 4 cover screws from back of Remote Control case. 2. Replace old battery pack with new battery pack. NOTE: A battery tray is provided with the tug. It can be used with standard AA rechargeable batteries.
-
Page 14: Track Tools
TRACK TOOLS The Track Tools are used to assist in the installation of new tracks. NOTE: This section is intended to show how the tools are used only. A detailed instruction guide is provided when purchasing new tracks. Refer to that instruction guide when installing new tracks. -
Page 15: Limited Manufacturer's Warranty
Trailer Valet’s directions to make a claim on your warranty. TO MAKE A WARRANTY CLAIM: TRAILER VALET SHALL HAVE THE Contact us either through: EXCLUSIVE RIGHT TO DETERMINE PHONE: (844) 846-9344 IF A UNIT IS COVERED UNDER EMAIL: support@trailervalet.com... - Page 16 Copyright 2021 by Supertech S. Corporation. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Supertech S. Corporation. For further information or if you have any questions, please contact: SUPERTECH S.
Need help?
Do you have a question about the RVR12 and is the answer not in the manual?
Questions and answers