JVC KD-G334 Installation & Connection Manual

KD-G334
Installation/Connection Manual
GET0404-002B
[ ]
UI
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.
WARNINGS
To prevent short circuits, we recommend that you disconnect the battery's negative terminal and make all
electrical connections before installing the unit.
•
Be sure to ground this unit to the car's chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio
dealer.
•
It is recommended to connect to the speakers with maximum power of more than 50 W (both at
the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than
50 W, change "AMP GAIN" setting to prevent the speakers from being damaged (see page 12 of the
INSTRUCTIONS).
•
To prevent short-circuit, cover the terminals of the UNUSED leads
with insulating tape.
•
The heat sink becomes very hot after use. Be careful not to touch it
when removing this unit.
PRECAUTIONS on power supply and speaker connections:
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit
will be seriously damaged.
•
BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
Parts list for installation and connection
The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer
immediately.
A / B
Hard case/Control panel
E
Power cord
TROUBLESHOOTING
•
The fuse blows.
* Are the red and black leads connected correctly?
•
Power cannot be turned on.
* Is the yellow lead connected?
•
No sound from the speakers.
* Is the speaker output lead short-circuited?
•
Sound is distorted.
* Is the speaker output lead grounded?
*
Are the "–" terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
*
Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
• This unit becomes hot.
*
Is the speaker output lead grounded?
*
Are the "–" terminals of L and R speakers grounded in common?
•
This unit does not work at all.
*
Have you reset your unit?
* 1
When you stand the unit, be careful not to damage the fuse on the rear.
* 2 Rubber cushion—Not supplied for this unit
* 3
Mounting bolt (M5 × 20 mm)—Not supplied for this unit
* 4
Washer (ø5)—Not supplied for this unit
*
5 Lock nut (M5)—Not supplied for this unit
* 6
Not supplied for this unit.
Heat sink
C D
Sleeve Trim plate
F G
Handles Remote controller
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
•
If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Removing the unit
Before removing the unit, release the rear section.
H
Battery
Insert the two handles, then pull them as
illustrated so that the unit can be removed.
When using the optional stay
Dashboard
1
© 2009 Victor Company of Japan, Limited
Do the required electrical
connections.
Bend the appropriate tabs to hold
the sleeve firmly in place.
When installing the unit
without using the sleeve
Fire wall
In a Toyota car for example, first remove
the car radio and install the unit in its
Stay
place.
(option)
Flat type screws (M5 × 8 mm)
* 6
Bracket
Screw
(option)
Pocket
Note:
When installing the unit on the mounting
Install the unit at an
bracket, make sure to use the 8 mm-long
angle of less than 30˚.
screws. If longer screws are used, they
could damage the unit.
0409DTSMDTJEIN
EN
* 6
Flat type screws
(M5 × 8 mm) *
6
*
6
Bracket