Sealey EL144USB Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
instructions
1. safety
1.1. electrical safety
waRninG! it is the user's responsibility to check the following:
‰
check all electrical equipment and appliances to ensure that they are safe before using. inspect power supply leads, plugs and
all electrical connections for wear and damage. sealey recommend that an rcd (residual current device) is used with all electrical
products. You may obtain an rcd by contacting your local sealey stockist.
if used in the course of business duties, it must be maintained in a safe condition and routinely PAt (Portable Appliance test) tested.
electrical safety information, it is important that the following information is read and understood.
ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse - see
9
fuse rating in these instructions.
Do not pull or carry the appliance by the power cable.
8
Do not pull the plug from the socket by the cable.
8
Do not use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
This product is fitted with a BS1363/A 13 Amp 3 pin plug.
9
if the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualified electrician.
2. intRoDuction
space saving cube design. Suitable for garage, workshop and office applications. Features 2 x 5V (2.1A) USB sockets and 4 x 230V sockets.
Fitted with BS approved 3pin (13A) heavy-duty plug. Supplied with bracket, suitable for mounting under desks (covers one socket).
3. specification
model no .............................................................. EL144USB
colour ...........................................................................White
sockets ........................................4 x 230V, 2 x USB 5V 2.1A
cable section ..................................................... 3 x 1.25mm
cable length .................................................................. 1.4m
4. opeRation
4.1. The cube can be used as a stand alone or fixed item (using
the bracket supplied).
4.2. To fix the cube to a desk.
4.2.1. Peel off one side of the self adhesive pads and position on
the bracket ( the pad will fit in the recess on the back of
the bracket, leaving the holes free to receive the screws).
4.2.2. Position the bracket and stick to surface making sure there
is access around cube for sockets to be used.
4.2.3. Use screws provided to fix to desk. ( Dependant on the
surface to be fixed to alternative fixings may be required).
© Jack sealey limited
instructions for
extension cable cube 1.4mtr 4x230v +
2xusb sockets - white
el144usb
model no:
2
Original Language Version
recommended fuse rating
13 Amp
eL144USB | Issue 1 13/02/18