Panasonic FX-505 C2 Series Instruction Manual

Thank you very much for purchasing Panasonic products.
Please read this Instruction Manual carefully and thoroughly for the correct and
optimum use of this product.
WARNING
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products which
meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel
protection applicable in each region or country.
INTENDED PRODUCTS FOR CE MARKING
1
This product complies with the following standards / regulations.
EMC Directive
<Standards in US / Canada>
ANSI/UL 60947-5-2, CAN/CSA C22.2 No.14
S1-G-1-2009, S2-W-5-2009
Caution about UL recognition
2 power supply unit.
Panasonic Marketing Europe GmbH Panasonic Testing Center
Winsbergring 15, 22525 Hamburg,Germany
2 PART DESCRIPTION
Sensing output 2 UP key
selection indicator
• Teaching
(Yellow)
• Threshold value
Sensing output 1
selection indicator
• Select setting items
(Yellow)
Sensing output 1
Digital display
operation indicator
(Green / Red)
(Orange)
MODE indicator: L / D (Yellow)
Sensing output 2
MODE indicator: CUST (Yellow)
operation indicator
(Orange) MODE indicator: PRO (Yellow)
<Reference>
Pressing down SET key + MODE key for 3 sec : Set key lock or Release key lock
3 MOUNTING
How to connect
1. Fit the rear part of the mounting sec-
2. Press down the rear part of the
mounting section of the unit on the
DIN rail and fit the front part of the
mounting section to the DIN rail.
1. Push the controller forward.
2.
to remove it.
1. Snap the fiber lock lever down till it
stops completely.
2.
inlets until they stops. (Note)
3. Return the fiber lock lever to the
original position till it stops.
If they are inserted in reverse, the sensing performance will deteriorate.
INSTRUCTION MANUAL
FX-505 -C2
MJE-FX505C2C No.0068-85V
SET key DOWN key
• Teaching • Teaching
• C o n f i r m s e t t i n g •
contents
• Select setting items
MODE key
• Select Modes
• Cancel during setting
• Select sensing output 1/2
by pressing long
2. Press down
1. Fit
35mm width DIN rail
1. Push forward
2. Lift up
3. Return
1. Snap
Fiber lock lever
Fiber for emitter
2. Insert
Fiber for
receiver
FD-G4 or FD-FM2
I/O CIRCUIT DIAGRAMS
4
<FX-505-C2>
(Brown) +V
(Pink) External input
(Black) Sensing output 1
(White) Sensing output 2
(Blue) 0V
(Gray) Monitor current output (4 to 20mA)
<FX-505P-C2>
(Brown) +V
(Black) Sensing output 1
(White) Sensing output 2
(Pink) External input
(Blue) 0V
(Gray) Monitor current output (4 to 20mA)
Note: Make sure to insulate the ends of the unused lead wires.
5 OPERATION PROCEDURE
The sensing output can be switched to sensing output 1 or sensing output 2
by holding down the mode key.
The changed settings are not stored if turning the power OFF while setting.
power OFF.
When turning ON the power, RUN mode is displayed and the digital display
shows the threshold value (green) and the incident light intensity (red).
<RUN mode>
• Displays threshold value (green) and incident light intensity (red).
•
can be set.
• For setting method of each function, refer to "
MODE," "
TION," or "
<Sensing output operation mode>
• Select either Light-ON or Dark-ON.
• For the setting, refer to "
MODE."
• The default setting is "
<CUSTOM mode>
• An item set in CUSTOM mode (Response time setting, Emission
power setting and Hysteresis setting) is displayed.
• For details, refer to "
• The default setting is "
<PRO mode>
• Advanced setting can be done.
• For the setting, refer to "
<RUN mode>
Load
Load
+
12 to 24V DC
%
-
Load
+
12 to 24V DC
%
-
Load
Load
Load
TEACHING
THRESHOLD VALUE FINE ADJUSTMENT FUNC-
KEY LOCK FUNCTION."
SENSING OUTPUT OPERATION
" (Light-ON).
CUSTOM MODE."
" (response time setting).
PRO MODE."