Vexta SMK216A-GN Instructions page 2

INSTRUCTIONS
Low-Speed Synchronous Motor
Thank you for selecting this ORIENTAL MOTOR product.
To ensure correct operation, please read these instructions carefully
before using the motor.
■ Specifications
Motor Model
Single shaft Double shaft
0CSM2-0201
0CSM2-0202
0CSM2-0201A
0CSM2-0202A
0CSM-0201
0CSM-0202
0CSM-0201A
0CSM-0202A
＊ 2CSM-101
＊ 2CSM-102
＊ 4CSM-101
＊ 4CSM-102
4CSM-201
4CSM-202
＊ 4CSM-111
＊ 4CSM-112
SMK014K-A
−
SMK014K-AA
＊
SMK237A-A
−
＊
SMK216A-GN
−
＊
SMK5100A-A
−
＊
SMK5100A-AA
＊
SMK5160A-A
−
＊
SMK5160A-AA
＊
SMK550A-GN
−
＊ UL recognized (impedance protected)
◎ The capacitor for the 2CSM type when used with a 115V power supply is not provided.
Contact your nearest Oriental Motor office if required.
■ Mounting Hole of 0CSM and SMK0 Type
Motor Model
Single Shaft Double Shaft
0CSM2-0201 0CSM2-0202
0CSM-0201 0CSM-0202
SMK014K-A
0CSM2-0201A 0CSM2-0202A
0CSM-0201A 0CSM-0202A
SMK014K-AA
■ Wiring Diagrams
(The wiring diagram varies according to the motor model.)
Connections for operation are shown in following diagram:
To rotate the motor in a clockwise direction, flip switch (SW) to CW. To rotate it in a counter-
clockwise direction, flip this same switch (SW) to CCW. The motor will stop immediately when
the power supply is cut. The direction of motor rotation is as viewed from the front shaft end of
the motor.
● 0CSM, 2CSM, SMK0, SMK2 Type ● 4CSM, SMK5 Type
■ Wiring Diagram
CCW
Red
CW
White
Line
Blue
SW
CCW
Motor
Capacitor
＊ White wire is gray for
2CSM, SMK2 type.
● For the standard type motors, the capacitor required depends on the operating frequency (50
or 60Hz). Confirm the frequency and connect the appropriate capacitor.
Voltage Frequency Speed Capacitor
V･AC Hz r/min Mfd Ohm Watts
50 30
24 12
60 36
15
50 60
24
10
60 72
2.0
50 60
100
1.5
60 72
1.2
115
60 72
100 2.0
50 60
400
◎ 115 1.5
60 72
200 0.5
50 60
1500
220 0.4
60 72
100 3.5
50 60
400
115 2.5
60 72
50 60
24 12
60 72
50 60
100
1.2
60 72
115
60 72
50 60
100
1.2
60 72
115
60 72
50 60
100
2.5 400
60 72
115
60 72
50 60
100
2.5 400
60 72
115
60 72
50 60
100
60 72 0.6 400
115
60 72
Size of Mounting Hole
M3 P0.5 4.5mm deep min.
No.4-40UNC 4.5mm deep min.
■ Wiring Diagram
CW
CW
Line
SW
CCW
External Resistor
Capacitor
■ Installing The Motor
● Round Shaft Motor
Use screws of appropriate length and secure the motor so that there are no gaps between the
motor flange face and the mounting surface.
0CSM, SMK0 Type
Spot Facing or
Through Hole for Pilot
Hexagonal Socket Screw
● Pinion Shaft Motor
Use screws provided with gearhead and secure
the motor so that there are no gaps between the
Resistor
motor flange face and the mounting surface.
− −
− −
− −
■ Connecting The Gearhead
− −
Pinion shaft motors can be connected with the gearhead. Applicable gearheads are shown in
30
the table below.
30
Motor Model
SMK216A-GN
30
SMK550A-GN
− −
■ Precautions For Operation
● Do not lock the motor.
− −
Strong vibration will occur when motor is locked.
Please operate the motor within the range of the permissible inertia load.
● Be sure to use the capacitor that comes with the motor.
− −
When motors are running, a voltage of twice the motor power supply is applied across the
terminals of the capacitor. The terminals must therefore be insulated to ensure safety.
● When using the gearhead
30
The permissible torque indicates the maximum load torque that can be applied to the gearhead.
Be sure the load torque does not exceed the permissible torque.
Rotation of the gearhead s output shaft may be in the reverse direction to the rotation of the
30
motor shaft due to the reduction ratio. Before connection, make sure of the correlation between
the reduction of rotation.
● Do not disassemble the motor.
30
Disassemble the motor will results in a considerable reduction in its performance. Also be careful
not to drop the motor or subject it to shock.
● Operating Conditions
The motors must not be used in locations of the following conditions:
In locations where strong vibrations or shock occur.
Dusty locations.
Locations where water or oil is likely to come into contact with the motor.
Locations where flammable or corrosive gas is present.
Location where the ambient temperature is outside the permissible temperature range of -10℃
to +40℃
Characteristics, specifications and dimensions are subject to change without notice.
Please contact your nearest ORIENTAL MOTOR office for further information.
ORIENTAL MOTOR U.S.A. CORP.
Los Angeles Office
San Jose Office
Chicago Office
Cincinnati Office
Austin Office
New York Office
Boston Office
Atlanta Office
Canada Office
Technical Support Line Tel:(800)468-3982
Available from 8:30 AM to 8:00 PM. Eastern Time
ORIENTAL MOTOR ( EUROPA ) GmbH
Headquarters and Düsseldorf Office
Munich Office
Hamburg Office
ORIENTAL MOTOR ( UK ) LTD.
CCW CW
Tel:01252-519809 Fax:01252-547086
ORIENTAL MOTOR ITALIA s.r.l.
Red
Tel:02-3390541 Fax:02-33910033
Gray
Motor TAIWAN ORIENTAL MOTOR CO., LTD.
Blue
Tel:(02)2299-9360 Fax:(02)2299-4173
SINGAPORE ORIENTAL MOTOR PTE LTD.
Tel:(745)7344 Fax:(745)9405
ORIENTAL MOTOR･KOREA CO., LTD.
Tel:(02)632-9122 Fax:(02)679-4588
ORIENTAL MOTOR CO., LTD.
Headquarters Tel:(03)3835-0684 Fax:(03)3835-1890
2CSM, 4CSM, SMK2, SMK5 Type
Hexagonal Socket Screw
4-M3P0.5
(4-No.4-40 UNC)
Mounting Plate
Gearhead
Applicable Gearhead
2GN □ K
5GN □ K
Tel:(310)784-8200 Fax:(310)325-1076
Tel:(408)358-6900 Fax:(408)358-8200
Tel:(847)240-2649 Fax:(847)240-2753
Tel:(513)563-2722 Fax:(513)956-3183
Tel:(512)918-9438 Fax:(512)335-5983
Tel:(973)359-1100 Fax:(973)359-1090
Tel:(781)848-2426 Fax:(781)848-2617
Tel:(770)716-2800 Fax:(770)719-8515
Tel:(905)502-5333 Fax:(905)502-5444
Tel:02131-95280 Fax:02131-952899
Tel:08131-59880 Fax:08131-598888
Tel:04076-910443 Fax:04076-910445
ORIENTAL MOTOR ( FRANCE ) SARL
Tel:01 47 86 97 50 Fax:01 47 82 45 16
Spot Facing or
Through Hole for Pilot
Hexagonal Nut
Spring Washer
Mounting Plate
Motor
Screws Provided
with Gearhead
The box ( □ ) in the gearhead
model name represents the gear
ratio.
Printed on Recycled Paper