Related Manuals for Felder FB 510
Summary of Contents for Felder FB 510
- Page 1 User manual (Translation) Bandsaw FB 510/610/710 FB 710 c-tech Keep this manual handy and in good condition for continual reference! Dok.ID: 424033-901_02 • Englisch • 2021-03-05...
- Page 2 Bandsaw FB 510/610/710 & FB 710 c-tech Note: Year of construction The machine number of this machine will be printed on the cover sheet of this operating manual. The final two digits of the machine number show the year of construction of this machine.
-
Page 3: Table Of Contents
Bandsaw FB 510/610/710 & FB 710 c-tech Table of contents Table of contents 1 General ......................5 1.1 Symbol legend .......................5 1.2 Information about the manual ..................5 1.3 Liability and warranty .....................6 1.4 Copyright ........................6 1.5 Warranty notice ......................6 1.6 Spare parts ........................7 1.7 Disposal ........................7... - Page 4 Bandsaw FB 510/610/710 & FB 710 c-tech Table of contents 7 Operation ....................21 7.1 Safety instructions ......................21 7.2 Blade selection and maintenance ...................22 7.3 Saw blade replacement/tension ..................23 7.4 Table pad and wooden pad for dust extraction ..............23 7.5 Adjusting the saw blade guide ..................24 7.5.1 Height adjustable protection device ................24...
-
Page 5: General
Bandsaw FB 510/610/710 & FB 710 c-tech General 1 General 1.1 Symbol legend Important technical safety instructions in this manual are In all these particular cases, special attention must be marked with symbols. paid in order to avoid accidents, injury to persons or These instructions for work safety must be followed. -
Page 6: Liability And Warranty
This manual, in its entirety or parts thereof, may not be transferred to third parties or copied in any way or 1.5 Warranty notice The guarantee period is in accordance with national guidelines. Details may be found on our website, www.felder-group.com... -
Page 7: Spare Parts
Bandsaw FB 510/610/710 & FB 710 c-tech General 1.6 Spare parts Attention! Non genuine, counterfeit or faulty spare parts may result in damage, cause malfunction or com- plete breakdown of the machine. If unauthorised spare parts are fitted into the machine, and representatives shall be rejected. -
Page 8: Safety
Bandsaw FB 510/610/710 & FB 710 c-tech Safety 2 Safety At the time of its development and production, the safety and ensure the safe and trouble-free operation of machine was built in accordance with prevailing the machine. technological regulations and therefore conforms to To further minimise risks, the other chapters of this industry safety standards. -
Page 9: Making Changes And Modifications To The Machine
Bandsaw FB 510/610/710 & FB 710 c-tech Safety 2.3 Making changes and modifications to the machine In order to minimise risks and to ensure optimal perfor- machine must be kept visible, readable and may not be mance, it is strictly prohibited to alter, retrofit or modify removed. -
Page 10: Personal Protective Equipment
Bandsaw FB 510/610/710 & FB 710 c-tech Safety 2.7 Personal protective equipment When working on or with the machine, the following must be strictly observed: Persons with long hair who are not wearing a hairnet are not permitted to work on or with the machine! -
Page 11: Declaration Of Conformity
KR-FELDER-STR.1 A-6060 Hall in Tirol Product designation: Bandsaw Bandsaw FELDER Make: FB 510 / FB 610 / FB 710 Model designation: 2006/42/EG The following EC guidelines were applied: 2014/30/EU EN 1807-1 The following harmonised norms were applied: This EC Declaration of Conformity is valid only if the CE label has been affixed to the machine. -
Page 12: Specifications
Bandsaw FB 510/610/710 & FB 710 c-tech Specifications 4 Specifications 4.1 Dimensions and weight Machine (L x W x H) FB 510 FB 610 FB 710 Total size (mm) 454 x 460 x 490 x 829 x 985 x 1110 x... -
Page 13: Noise Emission
Bandsaw FB 510/610/710 & FB 710 c-tech Specifications 4.3 Noise emission The specified values are emission values and therefore and other ambient influences. The permissible workplace do not represent safe workplace values. Even though a values may also differ from country to country. Neverthe-... -
Page 14: Dust Extractors
" Connection ports 120 mm Warning! Risk of injury! The dust extraction hose must be non-flammable and must not conduct electricity! For this reason, only use genuine FELDER dust extraction hoses! • In addition, the vacuum performance must be sufficient •... -
Page 15: Assembly
Bandsaw FB 510/610/710 & FB 710 c-tech Assembly 5. Assembly 5.1 Overview " & Fig. 5-1: Overview Machine base-frame Guide fence " Upper wheel Saw blade track - Adjuster hand wheel and clamping Lower wheel lever Rising part of saw blade... -
Page 16: Data Plate
Fig. 5-2: Data plate 5.3 Automatic braking system Your machine is equipped with an automatic braking Please contact the FELDER KG service department, if unit. The brake is a maintenance-free DC braking unit. problems or a fault- function should occur! All necessary adjustments are done by FELDER KG. -
Page 17: Setup And Installation
Bandsaw FB 510/610/710 & FB 710 c-tech Setup and installation 6 Setup and installation 6.1 Safety instructions Warning! Risk of injury! Improper assembly and installation can lead to serious physical injury or equipment damage. For this reason, this work may only be carried out by authorised, trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions. -
Page 18: Transporting The Machine
Bandsaw FB 510/610/710 & FB 710 c-tech Setup and installation 6.3 Transporting the machine Attention! Risk of material damage! Do not lift the machine by its work table, extension frames or hand- wheels. The machine can be transported with a crane, forklift, pallet jack or rolling carriage. -
Page 19: Positioning And Levelling The Machine
Bandsaw FB 510/610/710 & FB 710 c-tech Setup and installation 6.5 Positioning and levelling the machine Note: There are 4 threaded holes located in the base plate of the machine where the levelling screws sup- plied with the machine can be screwed into. -
Page 20: Electrical Connection
Note: The machine’s circuit box may only be opened with the express consent of the FELDER service team. Violating this stipulation shall render the right to make claims under the warranty null and void. -
Page 21: Operation
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7 Operation 7.1 Safety instructions Warning! Risk of injury! Improper operation may lead to severe physical injury or material damage. For this reason, this work may only be carried out by authorised, trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions. -
Page 22: Blade Selection And Maintenance
See the FELDER catalogue " The following saw blades may be used: FB 510 Saw blade length: 4318 mm Saw blade width: 6 – 25 mm FB 610 Saw blade length: 4546 mm Saw blade width: 6 – 30 mm FB 710 Saw blade length: 5120 mm Saw blade width: 6 –... -
Page 23: Saw Blade Replacement/Tension
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7.3 Saw blade replacement/tension 1. Disconnect the machine from the mains supply. 2. Remove table insert and positioning pin. Open wheel door. 3. Loosen the blade tension hand wheel by turning it clockwise. -
Page 24: Adjusting The Saw Blade Guide
Fig. 7-5: Bearings 7.5.2 Saw blade guide up / down Note:: Ceramic bandsaw blade guide FB 510 / 610 = Option / FB 710 = Standard Accessories - Order no.: 423-037 / 423-038 " See assembly instructions: 423033-901 The side guide rollers should touch the saw blade slightly so as to obtain a straight and vibration-free cut. -
Page 25: Switching On The Machine / Switching Off The Machine
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7.6 Switching on the machine / Switching off the machine Warning! Risk of injury due to insufficient preparation! It is only permitted to switch on the machine if, for the work at hand, the required preconditions are fulfilled and any preliminary work is completed. -
Page 26: Cutting Round Workpieces In The Transverse Direction
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7.7.2 Cutting round workpieces in the transverse direction Use an appropriate device with the minimum measure- ments as depicted in Fig. to avoid the workpiece twisting during the cutting process. Fig. 7-9: Cutting a circular workpiece 7.7.3 Longitudinal cut of narrow or thin work-pieces... -
Page 27: Mitre Cuts
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7.7.5 Mitre cuts Use auxiliary equipment as depicted in the figure. Fig. 7-12: Mitre cuts 7.7.6 Circular cuts Use auxiliary equipment as depicted in the figure. Accessories Order no.: 01.1.300 Fig. 7-13: Circular cuts 7.7.7 Diagonal cross-cut of rectangular workpieces... -
Page 28: Tilting The Table
Bandsaw FB 510/610/710 & FB 710 c-tech Operation 7.7.8 Tilting the table The machine working table can be tilted up to an angle from -5° (FB 500: -10°) up to +45°. Adjusting the angle: To tilt, remove the table padding to enable the saw belt to move through the table unimpeded. -
Page 29: Service
Bandsaw FB 510/610/710 & FB 710 c-tech Service 8 Service 8.1 Safety instructions Warning! Risk of injury! Improper adjustment and setup work can lead to serious physical injury or material damage. For this reason, this work may only be carried out by authorised, trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions. -
Page 30: Replacing The Rubber Wearing Surface Of Wheels
Bandsaw FB 510/610/710 & FB 710 c-tech Service 8.3 Replacing the rubber wearing surface of wheels Its highly recommended that this work is only carried out by a specialist or the manufacturer. Removing the saw blade See chapter entitled: Saw blade replacement/tension 1. -
Page 31: Service C-Tech
Bandsaw FB 510/610/710 & FB 710 c-tech Faults 8.6 Service c-tech 8.6.1 Saw blade lubrication The lubricant flow must be adjusted according to the application with the click throttle. The felt cubes on the saw blade must be soaked with lu- bricant but must not drip. -
Page 32: Replacing The Flywheel Wiper
Put the wiper plate back against the flywheel. Fig. 8-7: Wiper top Note: Only use FELDER spare parts. The original spare parts that have been authorised for use are listed in a separate spare parts catalogue, enclo- sed in the documentation package supplied with the machine. -
Page 33: Faults
Bandsaw FB 510/610/710 & FB 710 c-tech Faults 9 Faults 9.1 Safety instructions Warning! Risk of injury! Repairing faults incorrectly can result in personal injury or damage to the machine. For this reason, this work may only be carried out by authorised, trained personnel who are familiar with how to operate the machine and in strict observance of all safety instructions. -
Page 34: Faults, Causes And Repairs
Bandsaw FB 510/610/710 & FB 710 c-tech Faults 9.4 Faults, causes and repairs Fault Cause and problem elimination Machine does not start Safety break switches are breaking the electric circuit Ensure that the side doors are closed properly Emergency stop switch engaged (FB 710 c-tech) Unlock the emergency stop switch... -
Page 35: Error Messages Speed Control
Bandsaw FB 510/610/710 & FB 710 c-tech Setup and installation Faults 9.4.1 Error messages speed control Description Cause and problem elimination SEC 1 The speed is above 0 and the machine has not started Error in electrical system 1. Exit error, restart machine ✆... - Page 36 FELDER KG KR-Felder-Str. 1 KR-FELDER-STR.1 A-6060 Hall in Tirol A-6060 Hall in Tirol Tel.: +43 (0) 52 23 / 58 50 0 Tel.: +43 (0) 5223 / 58 50 0 Fax: +43 (0) 52 23 / 56 13 0 Fax: +43 (0) 5223 / 56 13 0 E-mail: info@felder.at...
Need help?
Do you have a question about the FB 510 and is the answer not in the manual?
Questions and answers