Summary of Contents for Panasonic INDUSTRY PAN9028
Page 1
PAN9028 ® Wi-Fi Dual Band 2.4 GHz/5 GHz and Bluetooth Module Module Integration Guide Rev. 1.0 Wireless Connectivity...
Page 2
PAN9028 Wi-Fi/Bluetooth Module 1 About This Document Overview • Coexistence interface for arbitration of co-located WLAN, Bluetooth, or mobile wireless system The PAN9028 is a 2.4 GHz/5 GHz ISM band Wi-Fi ® (e.g. LTE or ZigBee and Bluetooth radio module, which includes a •...
Page 3
Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Module Integration Guide before initiating or completing a design.
Page 4
To the maximum extent allowable by Law Panasonic assumes no liability whatsoever including without limitation, indirect, consequential, special, or incidental damages or loss, including without limitation loss of profits, loss of opportunities, business interruption, and loss of data.
PAN9028 Wi-Fi/Bluetooth Module 1 About This Document Table of Contents About This Document ......................... 7 Purpose and Audience ....................7 Revision History ......................7 Use of Symbols ......................7 Related Documents ....................... 8 Overview .............................. 9 PAN9028 Module ..........................10 Block Diagram ......................
Page 6
PAN9028 Wi-Fi/Bluetooth Module 1 About This Document 11.2 Product Information ..................... 45 Module Integration Guide Rev. 1.0 Page 6 of 45...
PAN9028 Wi-Fi/Bluetooth Module 1 About This Document 1 About This Document 1.1 Purpose and Audience This Module Integration Guide is intended to support the easy integration of the PAN9028 into a product and to ensure the compliance with regulatory requirements. This guide gives an overview about the hardware design requirements by providing a reference design, which is the evaluation board of the PAN9028.
The message Failed to save your data is displayed. Enter the value Product 123. Indicates a key on the keyboard, e.g. F10 . 1.4 Related Documents For related documents please refer to the Panasonic website 11.2 Product Information. Module Integration Guide Rev. 1.0...
Tx power calibration data, Wi-Fi, and Bluetooth system parameters are pre-stored on the One Time Programmable memory of the PAN9028 during production at Panasonic. This simplifies passing the certification process for PAN9028 customers. Furthermore, the module reduces design, test, and calibration effort resulting in reduced time- to-market compared to discrete solutions.
PAN9028 Wi-Fi/Bluetooth Module 3 PAN9028 Module 3.3 Footprint The outer dimensions have a tolerance of ±0.35 mm. Module Integration Guide Rev. 1.0 Page 12 of 45...
PAN9028 Wi-Fi/Bluetooth Module 3 PAN9028 Module 3.4 Solder Mask It is recommended to use the following layout for the soldering mask to reduce voids on the thermal pads. Use the dimensions: The Resist Mask should be 50 µm bigger than the pad size ( Footprint).
Page 14
PAN9028 Wi-Fi/Bluetooth Module 3 PAN9028 Module The antenna requires a cutout area of 8 mm x 5 mm under the PAN9028 module. This “Keep out Area” shall be located in every layer under the module antenna. Note for example the “Keep out Area”...
PAN9028 Wi-Fi/Bluetooth Module 4 Power Supply 4 Power Supply The following conditions must be met: The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module).
PAN9028 Wi-Fi/Bluetooth Module 5 RF Path 5 RF Path 5.1 External Antenna Antenna Warning The PAN9028 is tested with a standard U.FL connector and with the antenna listed in the regulatory and certification chapter of the “PAN9028 Product Specification”. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non- approved antennas.
Page 17
PAN9028 Wi-Fi/Bluetooth Module 5 RF Path Example 1: 50 ohm Coplanar Waveguide with Ground on mSDIO Adapter Trace width W = 180 µm Trace distance to ground S = 150 µm Substrate thickness H = 80 µm Effective permittivity = 3.9 Loss tangent tan = 0.015 Module Integration Guide Rev.
Page 18
PAN9028 Wi-Fi/Bluetooth Module 5 RF Path Example 2: 50 ohm Coplanar Waveguide with Ground and Micro Vias Trace width W = 300 µm Trace distance to ground S = 300 µm Substrate thickness H = 160 µm Effective permittivity = 4.2 Loss tangent tan = 0.006 Module Integration Guide Rev.
PAN9028 Wi-Fi/Bluetooth Module 6 One-Layer Example for 6 One-Layer Example for Module Variant ENWF940[x]A1EF Functionality • WLAN interface: SDIO with 3.3 V • Bluetooth interface: SDIO with 3.3 V • On-board antenna • No GPIOs connected • Reset available Module Integration Guide Rev. 1.0 Page 19 of 45...
PAN9028 Wi-Fi/Bluetooth Module 7 mSDIO Adapter 7 mSDIO Adapter 7.1 Functional Blocks Functional Block Description Interface On-board antenna or bottom pad selection U.FL connector PAN9028 module SDIO interface Bluetooth data over UART or SDIO Bluetooth Interface External supply voltage can be connected 7.2 Resistor Jumper Configuration RF-Out n.c.
PAN9028 Wi-Fi/Bluetooth Module 9 Cautions 9 Cautions Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module. 9.1 Design Notes 1. Follow the conditions written in this specification, especially the control signals of this module.
PAN9028 Wi-Fi/Bluetooth Module 9 Cautions 9.3 Usage Condition Notes 1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2.
Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting.
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 29
The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label (laser marking) on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above.
Page 30
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.1.5 Approved Antenna List Item Part Number Manufacturer Type Polarization Frequency Band Gain (dBi) 1 ANT162442DT- Chip Linear 2.400 - 2.484 GHz 2001A2 Antenna 5.150 - 5.850 GHz 10.1.6 RF Exposure To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 10.1.5 Approved Antenna List.
Page 31
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 47 CFR Section Part 15C Frequency Band (MHz) 2 400 to 2 483.5 Systems Frequency Hopping Systems operating within the 2 400 - 2 483.5 MHz Band Reference / Requirement 15.247(a)(1), 15.247(a)(1)(iii), 15.247(b)(1), 15.207, 15.247(d) Complied Module M/N ENWF9408A1EF, ENWF9408A2EF 47 CFR Section...
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.2 Innovation, Science, and Economic Development (ISED) for Canada English PAN9028 and versions are licensed to meet the regulatory requirements of ISED. License for M/N: ENWF9408A1EF: IC: 216Q-9028 License for M/N: ENWF9408A2EF: IC: 216Q-9028 Manufacturers of mobile, fixed, or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits.
Page 33
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi radio apparatus operating in the bands 2 400 MHz to 2 483.5 MHz and 5 725 MHz to 5 850 MHz employing frequency hopping, digital modulation and/or a combination (hybrid) of both techniques. It also includes license exempt local area network (LE-LAN) devices operating in the bands 5 150 MHz to 5 250 MHz, 5 250 MHz to 5 350 MHz, 5 470 MHz to 5 725 MHz and 5 725 MHz to 5 850 MHz as specified in SP-5 150 MHz.
Page 34
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi RSS-247 Section Frequency Band (MHz) 2 400 to 2 483.5 Systems Frequency Hopping Systems Systems out of Scope FHS operating in the band 5 725 MHz to 5 850 MHz Fixed point-to-point systems Requirements The maximum peak conducted output power shall not exceed W if the hopset uses 75 or more hopping channels;...
Page 35
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi RSS-247 Section Frequency Band (MHz) 2 400 to 2 483.5 Systems FHSs operating in the band 2 400 to 2 483.5 MHz. DTSs employing digital modulation techniques operating in the band 2 400 MHz to 2 483.5 MHz. Systems out of Scope FHSs operating in the band 902 MHz to 928 MHz and 5 725 MHz to 5 850 MHz.
Page 36
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.2.1.5 Requirements for LE-LAN and DTS operating in the 5 GHz Band The section provides standards for Licence-Exempt Local Area Network (LE-LAN) devices operating in the bands: • 5 150 to 5 250 MHz, •...
Page 37
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi RSS-247 Section 6.2.4 Frequency Band (MHz) 5 725 to 5 850 Device Type For equipment operating in the band 5 725 MHz to 5 850 MHz Devices out of Scope Fixed point-to-point devices and devices with antenna gain greater than 6 dBi. Power Limits The minimum 6 dB bandwidth shall be at least 500 kHz.
Page 38
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.2.2 IC Notice English The device PAN9028 and versions ( see PAN9028 Product Specification for ordering information), including the antennas ( 10.1.5 Approved Antenna List), comply with Canada RSS-Gen Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen.
Page 39
The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifiers are:...
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.3 European Conformity According to RED (2014/53/EU) The PAN9028 modules with model number ENWF9408A1EF and ENWF9408A2EF comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1:2014 EN 62311:2008...
Page 41
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi 10.3.1 Radio Equipment Directive The Radio Equipment Directive 2014/53/EU (RED) establishes a regulatory framework for placing radio equipment on the market. It ensures a Single Market for radio equipment by setting essential requirements for safety and health, electromagnetic compatibility, and the efficient use of the radio spectrum.
Page 42
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi b) The radio interfaces which, in accordance with implementing acts adopted pursuant to paragraph 2 of this Article, correspond to radio equipment which can be put into service and used without restrictions within the Union. 2) The Commission shall adopt implementing acts establishing the equivalence between notified radio interfaces and assigning a radio equipment class, details of which shall be published in the Official Journal of the European Union.
Page 43
PAN9028 Wi-Fi/Bluetooth Module 10 Regulatory and Certi Application/Reference Transmit Power/Power Density Sub-class Frequency Band of Class 2 (MHz) Wireless Access Systems 5 150 to 5 350 Max. 200 mW mean e.i.r.p. and max. including Radio Local Area 10 mW/MHz mean e.i.r.p. density in any Networks (WAS/RLANs) 1 MHz band.
For further information please refer to the Bluetooth website www.bluetooth.com. 10.5 RoHS And REACH Declaration The latest declaration of environmental compatibility (RoHS and REACH) for supplied products can be found on the Panasonic website in the “Downloads” section of the respective product 11.2 Product Information.
PAN9028 Wi-Fi/Bluetooth Module 11 Contact Details 11 Contact Details 11.1 Contact Us Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic website “Sales &...