Sealey 3000LJ Instructions

Your new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properly
maintained, give you years of trouble free performance.
ImpORTANT: reaD These iNsTrucTiONs carefully. NOTe The safe OPeraTiONal reQuireMeNTs, warNiNGs aND cauTiONs.
use This jack cOrrecTly aND wiTh care fOr The PurPOse fOr which iT is iNTeNDeD. failure TO DO sO May cause DaMaGe
Or PersONal iNjury aND will iNvaliDaTe The warraNTy. reTaiN These iNsTrucTiONs fOr fuTure use.
1. safeTy PrecauTiONs
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.

Use genuine parts only. The use of non genuine parts may be dangerous and will invalidate the warranty.
Locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials.

Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as the jack may sink in.

Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions.

Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or "PARK" if automatic).

Ensure minimum distance of 0.5m between the vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.

Ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use.

Place the jack under lifting points recommended by the vehicle manufacturer (see vehicle hand book). Ensure lifting point is stable and

centred on the saddle.
 DANGER: Use the jack for lifting only, NOT for supporting the lifted load.
Use suitable capacity axle stands under the vehicle before proceeding with any task.

Ensure there are no persons or obstructions beneath the vehicle before lowering.

 DO NOT operate the jack if damaged.
 DO NOT work under the vehicle until axle stands have been correctly positioned.
 DO NOT exceed the rated capacity of the jack and DO NOT adjust the safety overload valve.
 DO NOT jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.
 DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle.
 DO NOT top up the hydraulic system with brake fluid. Use hydraulic jack oil only and use a qualified person to maintain jack hydraulic
system.
 DO NOT allow untrained persons to operate the jack and DO NOT use jack for purposes other than for which it is designed.
 DO NOT allow persons to ride on the jack.
When not in use store the jack, fully lowered, in a safe, dry, childproof area.

2. iNTrODucTiON & sPecificaTiONs
steel framed 3tonne locking jacks with a three position safety locking mechanism that provides additional load security and hydraulic system
fail safe. Automatic bypass prevents jack damage from over pumping. for safety reasons always use in conjunction with axle stands in pairs.
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . 3000lj
capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Tonne
Locking Position 1: . . . . . . . . . . . . . . . . . . . 325mm
Locking Position 2: . . . . . . . . . . . . . . . . . . . 405mm
Locking Position 3: . . . . . . . . . . . . . . . . . . . 470mm
© Jack sealey Limited
InsTRUcTIons foR:
3tonne TrOlley jack wiTh safeTy lOck
3000lj
MoDEL no:
Min. saddle height . . . . . . . . . . . . . . . . . . . 145mm
Max. saddle height . . . . . . . . . . . . . . . . . . . 505mm
Max. chassis height . . . . . . . . . . . . . . . . . . 190mm
Length. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690mm
Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37kg
Original Language Version
3000LJ Issue: 1 - 05/03/14