Sealey SA1006 Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. Safety
waRning! ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
waRning! disconnect from air supply before changing the blade, servicing or performing maintenance.
‰
Maintain the saw in good condition (use an authorised service agent).
9
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9
Use in suitable clean and tidy work area, free from unrelated materials, ensure that there is adequate lighting.
9
waRning! Always wear approved eye or face and hand protection when operating the saw.
‰
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Wear appropriate protective clothing and keep hands and body clear of working parts.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the work area.
9
Check moving parts alignment on a regular basis.
9
ensure workpiece is secure before operating the saw.
9
never hold a workpiece by hand. Use a vice or clamps.
9
waRning! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 50-90psi.
‰
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
note: Prolonged exposure to vibration from this saw poses a health risk. It is the employer's/owner's responsibility to assess the hazard
correctly and issue guidelines for safe periods of use and offer suitable protective equipment.
Do not use any power source except an air compressor.
8
Do not operate saw near any flammable substance or on any container that has held a flammable substance.
8
Do not use the saw for a task it is not designed to perform.
8
Do not operate saw if any parts are damaged or missing as this may cause failure and/or personal injury.
8
Do not carry the saw by the hose, or pull the hose from the air supply.
8
Do not operate saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not carry the saw with your finger on the trigger.
8
When not in use disconnect from air supply and store in a safe, dry, childproof location.
9
2. intRoDuction
Textured finish to ensure a good grip. Suitable for a variety of bodyshop applications such as cutting through panels, sills, chassis members
etc. Excellent for initial crash-repair preparation when quick removal of damaged panels is required. Fitted with safety trigger device. Suitable
for the professional workshop. Supplied with starter pack of blades.
3. Specification
Model no: .......................................................................................... Sa1006
Air Consumption:.................................................................................. 8.5cfm
Free Speed: ......................................................................................4500rpm
Inlet Size: ...........................................................................................1/4"BSP
Maximum Cutting Capacity: ........................2mm (Steel), 2.5mm (Aluminium)
noise Power/Pressure: ................................................................. 88dB/77dB
Stroke: .................................................................................................7.9mm
Vibration/Uncertainty: ................................................................ 15.5/2.03m/s²
consumable parts:
SA34/B14 ..................................................................14tpi Air Saw Blade (x5)
SA34/B24 ..................................................................24tpi Air Saw Blade (x5)
SA34/B32 ..................................................................32tpi Air Saw Blade (x5)
© Jack Sealey limited
Mini RecipRocating aiR Saw
Model no:
Wear protective Wear ear
gloves protection
Original Language Version
Sa1006
Wear a mask
SA1006 Issue 1 18/12/19