Download Print this page

Sun-Co 24 X-Power Manual

Advertisement

Quick Links

DANGER
Ultraviolet radiation. Follow instructions. Avoid overexposure. As with
natural sunlight, overexposure can cause eye and skin injury and
allergic reactions. Repeated exposure may cause premature aging of the skin and skin cancer.
WEAR PROTECTIVE EYEWEAR; FAILURE TO MAY RESULT IN SEVERE BURNS OR
LONGTERM INJURY TO THE EYES. Medications or cosmetics may increase your sensitivity
to the ultraviolet radiation. Consult physician before using sunlamp if you are using medications
or have a history of skin problems or believe yourself especially sensitive to sunlight. If you do
not tan in the sun, you are unlikely to tan from the use of this product. Children, the elderly, or
fair skinned people who always burn easily and either never tan or tan minimally should not use
this equipment.
To use, lie down on bench and pull canopy down as far as adjustment will allow. Do not use
without clear plastic panels in place. Untanned persons should not tan on consecutive days dur-
ing their first week of tanning. Never tan more than once a day. Tanning normally appears after
the first few sessions and maximizes after approximately four weeks. Tan once or twice per week
thereafter to maintain appearance. Persons already having a base tan may begin at advanced
levels corresponding to the extent of their base tan.
Skin Type:
I
Sensitive Skin (Burns easily and severely and does not tan.)
II Light Skin
(Burns easily and severely and tans minimally.)
III Normal Skin
(Burns moderately and tans average.)
IV Dark Skin
(Burns minimally, tans easily and above average.)
RECOMMENDED EXPOSURE TIMES IN MINUTES
Level 1/Week 1
Skin Type: 1st-3rd Sessions
I Sensitive
II Light
3
III Normal
4
IV Dark
5
MAXIMUM EXPOSURE TIME IS 15 MINUTES
New lamps emit approximately 10% more ultraviolet radiation during the first 50 hours of
operation. Recommended tanning times should therefore be reduced by approximately 10%
during that period.
WARNING: • Read these instructions before using this sunlamp product. • All persons in the
room should wear protective eyewear when lamps are on. Recommended eyewear: provided
eyeshields or equivalent eyewear as defined under 21 CFR 1040.20. Other types of eyewear
may not provide adequate protection. Failure to use protective eyewear may result in severe
burns or other eye injury. If discomfort develops, discontinue use and consult a physician.
ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE 24 X-Power:
X-Power Wolff® Model XP71-T12-100W BI PIN
DISCONNECT POWER CORD BEFORE ATTEMPTING TO CLEAN, RELAMP,
OR ENGAGE IN THE MAINTENANCE OF THIS PRODUCT.
THIS EQUIPMENT MUST BE EARTH GROUNDED.
This product is in conformity with performance standards for sun lamp
products under 21 CFR PART 1040.20 and ANSI/UL Standard 482.
Subsequent
Level 2
Level 3
Level 4
Maximum
NOT RECOMMENDED FOR TANNING
6
9
12
7
11
15
9
13
15
Shock hazard.
Disconnect power before servicing or removing any protec-
tive covers.
Do not operate this device near water or while you are wet.
Some medications may increase your sensitivity to ultraviolet light. It
is recommended that you consult a physician before using this
sunbed if taking any medication or if you suspect that your skin might
be especially sensitive to sunlight.
Wear protective eyewear.
Failure to may result in severe burns or longterm injury to the eyes.
Use of a voltage source above 230V AC may prevent proper operation
of the sunbed and could cause damage and void the warranty.
Air from the room is used to cool the sunbed. Maximum ambient room
temperature should be 80°F. Place your sunbed no closer than 6" from
any wall. Make sure nothing obstructs the airflow into the sunbed's
15
endcaps or out of the fan openings. A poorly ventilated room may
15
cause the unit to become hot and cause discomfort to the user.
15
Electrical Requirements
Your sunbed operates from a 220V AC source. The 24 X-Power requires
a NEMA 6-20R electrical outlet (below) on a dedicated circuit capable
of providing 20 Amp service, installed in the room in which you will
use the unit. We recommend installation by a professional electrician.
The outlet must be earth grounded.
88465
DANGER
DANGER
WARNING
CAUTION
20 AMP NEMA #6-20R
RECEPTACLE
26713-01A - Page 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the 24 X-Power and is the answer not in the manual?

Questions and answers

Summary of Contents for Sun-Co 24 X-Power

  • Page 1 If discomfort develops, discontinue use and consult a physician. Your sunbed operates from a 220V AC source. The 24 X-Power requires ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE 24 X-Power: a NEMA 6-20R electrical outlet (below) on a dedicated circuit capable X-Power Wolff®...
  • Page 2 Unpacking and Inspection Hardware Inventory (These items and a small pillow) Your sunbed comes in two cardboard cartons. Pull back the plastic Allen-head Bolt 5/16” x 1” sheet and, with a helper, grasp the bench and pull it from the carton Hinge Brackets Quantity 2 bottom, leaving the plastic wrap and the carton packaging.
  • Page 3 Place the bushings Lift the canopy and hold it into hinge brackets. between the hinge brackets. Insert 5/16” x 1 1/2” bolts with nylon washers into both hinge brackets. Tighten bolts into the endcap threaded inserts until snug, then an additional half turn. Do not overtighten to avoid damaging threaded inserts.
  • Page 4 Remote Connections Setting the address manually Before connecting your sunbed to the T-Max® Manager or T-Max® 1A or 3A, the address of your sunbed must first be set. Set the address man- Your sunbed incorporates advanced circuitry allowing it to connect ually as described below.
  • Page 5 Using Your Sunbed Before using your sunbed, please note the following important pre- cautions. • Your skin should be free of cosmetics, tanning oils, or other body lotions prior to tanning except for those specifically made for use with tanning devices. However, do not remove natural body oils by bathing or showering immediately before tanning.
  • Page 6 Care and Maintenance Replacing Lamps To be assured of maximum tanning effectiveness, change lamps after Cleaning After Use approximately 800-1000 hours of use. Tanning will continue after this Clean and disinfect your tanning bed’s bench and canopy after each time but at a slower rate. To ensure trouble-free operation of your use.
  • Page 7: Troubleshooting

    Troubleshooting Troubleshooting Problem Problem Solution Solution Sunbed not tanning My bed won’t work with the T-Max® Manager remote system 1. Clean sunbed, see Thorough Periodic Cleaning. 1. The sunbed must first be set to a unique address, see 2. Ensure supply voltage is between 208 and 230V AC. Remote Connections.
  • Page 8: Limited Lifetime Warranty

    Limited Lifetime Warranty, contact SUN-CO, Inc. at 1-800-382-8932. SUN-CO, Inc. shall not be liable for loss of use, loss of time , inconvenience, rental or sub- stitute products, loss of business, loss of income, or any other incidental or consequential damages.