Related Manuals for Ketra D3 Series
Summary of Contents for Ketra D3 Series
- Page 1 Installation Guide Models CM-D3-HOUSING-X HW-D3-HOUSING HW-D3-HOUSING-XN CM-D3-HOUSING CM-D3-HOUSING-XN HW-D3-HOUSING-X...
- Page 2 Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: • This device may not cause interference. • This device must accept any interference, including interference that may cause undesired operation of the device. P/N 3662360 Rev C 2 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved.
-
Page 3: Table Of Contents
Part 4a: Apply Flangeless Mud-In Trim Retainer Part 4b: Flangeless Millwork Trim Retainer Installation (Wood/Stone Ceilings) Part 5: Apply Joint Compound Part 6: Apply Trim Additional Operations Troubleshooting Warranty & Tech Support P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 3... -
Page 4: Product Overview
Product Overview Ketra’s D3 family includes fixed, adjustable, and wall-wash downlights. Every model features a low-profile housing, wireless communication, and field-replaceable optics and electronics. With a wealth of trim and optic accessories, the D3 is ideal for a large variety of applications. It uses a fully-tunable spectrum capable of delivering high- quality white, saturated, and pastel light. -
Page 5: Included Components
120 V~ 60 Hz 13 W 109 mA; 220-277 V~ 50/60 Hz 13 W 47 mA - 60 mA 120 V~ 60 Hz 9 W 75 mA; 220-277 V~ 50/60 Hz 9 W 33 mA - 41 mA P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 5... -
Page 6: Installation
Allow horizontal movement • Allows horizontal or vertical movement post-mounting post-mounting • Ideal with wooden studs or • Ideal for commercial settings t-grid ceilings continued on next page P/N 3662360 Rev C 6 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved. - Page 7 Screw the ends of both bars into the wooden joists, fixing the housing in place (see fig. 3). T- Grid ceiling only: Bend the tabs on the nailer bars to lock them to the t-grid (see fig. 4). fig. 4 P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 7...
- Page 8 Tilt and rotate the emitter chassis to open an unobstructed path to the butterfly bracket openings Rotation Lock and Release on either side of the housing. Unlocked Locked Unlocked fig. 5 fig. 6 continued on next page P/N 3662360 Rev C 8 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved.
- Page 9 Note: The opening in the C-shaped kick reflector should face the wall. Reinsert the cardboard plug to protect the optic from dust during the rest of the installation. continued on next page P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 9...
- Page 10 Loosen the collar’s two outer screws, freeing the collar for rotation. Realign the collar using its v-shaped notches and an alignment string or laser. Re-tighten the screws to lock the collar’s new position. P/N 3662360 Rev C 10 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved.
-
Page 11: Part 2: Wire The Fixture
After verifying a successful installation, remove power and continue to Part Three. * Ketra lighting products should not be connected to, or directly controlled by, AC mains line voltage dimmers. These types of dimmers may also be referred to as phase cut, triac, forward-phase, reverse-phase, ELV, or MLV dimmers. Ketra's lighting products should only be controlled via our digital control architecture. -
Page 12: Part 3: Installing Drywall
1.125 in (28.575 mm), use the blue coded short set; for ceiling thickness in range 0.875 in (22.225 mm) to 1.5 in (38.1 mm), use the red coded long set. Note: The retainer assembly should be flush with the drywall. fig. 9 P/N 3662360 Rev C 12 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved. -
Page 13: Part 4B: Flangeless Millwork Trim Retainer Installation (Wood/Stone Ceilings)
Use a 5/64 in (2 mm) Allen key for the housing screw. Review the installation and ensure that the retainer is firmly installed before proceeding. Continue to Part 6 of the install guide. P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 13... -
Page 14: Part 5: Apply Joint Compound
Applying trim to flangeless mud-in downlight Press the flangeless trim into the trim retainer (see fig. 11). fig. 11 continued on next page P/N 3662360 Rev C 14 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved. - Page 15 1) CIRCLED DIMENSIONS ARE CRITICAL AND SUBJECT TO INSPECTION 2) MATERIAL: 3) FINISH: 4) COLOR: 5) ANY DEVIATIONS OR SUBSTITUTIONS MUST FIRST BE APPROVED BY A KETRA ENGINEER 6) PARTS TO BE CLEAN AND FREE FROM MACHINE OIL, REMOVE ALL BURRS AND BREAK SHARP EDGES DATE DRAWN BY...
-
Page 16: Additional Operations
To set optic at the low regress position pull optic directly down. Light engine will magnetically lock into place (see fig. 17). Emitter Regress Depth Adjust To Raise: Push To Lower: Pull fig. 16 fig. 17 P/N 3662360 Rev C 16 | D3 INSTALLATION GUIDE © 2019-2020 Ketra, Inc. All rights reserved. - Page 17 Disconnect emitter module Tilt locked at 40˚ . Emitter Module in Full Regress Unlocked and rotated so that Emitter Module tilts away from Power Supply P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. D3 INSTALLATION GUIDE | 17...
-
Page 18: Troubleshooting
D3 and other Ketra devices. Note: Magenta can indicate success or failure. It indicates success if there are no other powered-on Ketra devices within 50 ft (15.2 m); otherwise, it indicates a problem. -
Page 19: Warranty & Tech Support
For questions and technical support please contact: (844) 588-6445 ketrasupport@lutron.com Ketra and KetraNet are trademarks or registered trademarks of Lutron Ketra LLC, in the US and/or other countries. P/N 3662360 Rev C © 2019-2020 Ketra, Inc. All rights reserved. - Page 20 6231 E. Stassney Ln. www.ketra.com Bldg. 13, Suite 400 512.872.4349 Austin, TX 78744 P/N 3662360 Rev C...
Need help?
Do you have a question about the D3 Series and is the answer not in the manual?
Questions and answers