Page 1
ROOM AIR CONDITIONER OPERATION MANUAL INDOOR UNIT OUTDOOR UNIT AH-PNX21 AU-PNX21 AU-PNX25 AH-PNX25 Device of this mark is a trademark of Sharp Corporation. Plasmacluster is a registered trademark or a trademark of Sharp Corporation. EN-1 AH-XP18MV_EN.indd 1 11.5.23 11:21:12 AM...
ENGLISH Please read this manual carefully before using • Do not splash or pour water directly on the the product. This manual should be kept in a unit. Water can cause electrical shock or safe place for handy reference. equipment damage. •...
AUXILIARY MODE USING THE REMOTE CONTROL LOADING BATTERIES Use this mode when the remote control is not available. Remove the battery cover. TO TURN ON Insert two batteries. (AAA(R0)) Press the AUX button. Make sure the ( ) and ( ) polarities are cor- rectly aligned. • The red OPERATION lamp ( ) will light and the unit will start operating in the AUTO mode. Reinstall the battery cover.
BASIC OPERATION Press the MODE button to select the operation mode. AUTO COOL Press the ON/OFF button to start operation. • The red OPERATION lamp ( ) will light up. TO TURN OFF Press the ON/OFF button again. • The red OPERATION lamp ( ) will turn off. Press the THERMOSTAT button to set the desired temperature. (AUTO/DRY mode) The temperature can be changed up to ± °C the automatically set of temperature.
ADJUSTING THE AIR FLOW SUPER JET OPERATION DIRECTION The air conditioner works at the maximum VERTICAL AIR FLOW DIRECTION power and optimum louvre direction to Press the SWING button. makes the room cool rapidly. • The vertical airflow louvre will swing. During operation, press the SUPER JET button. Press the SWING button again to stop the desired position. • The remote control will display “ ”. • The adjustment range is narrower than • The temperature display will go off. the swing range in order to prevent con- •...
GENTLE COOL AIR PLASMACLUSTER OPERATION Plasmacluster ions released into the room The vertical airflow louvre is set obliquely upward to deliver cool air to the ceiling in will reduce some airborne mold. order to avoid direct airflow. During operation, press the During operation, press the PLASMACLUSTER button. GENTLE COOL AIR button. • The remote control will display “ ”. • The remote control will display “ ”. • The blue PLASMACLUSTER lamp ( will light up.
SELF CLEAN OPERATION ONE-HOUR OFF TIMER SELF CLEAN operation will reduce the When the ONE-HOUR OFF TIMER is set, the growth mold fungus with Plasmacluster unit will automatically turn off after one hour. ions and dry inside of the unit. Utilize the Press the ONE-HOUR OFF TIMER operation at seasonal change over terms or every 4 months. button. • The remote control will displays “ ”. Press the SELF CLEAN button when the unit is not operating. • The orange TIMER lamp ( ) will light • The remote control will display “ ”. • The blue PLASMACLUSTER lamp ( TO CANCEL will light up.
TIMER OPERATION TIMER ON TIMER OFF - SLEEP MODE Press the TIMER ON button and Press the TIMER OFF button and set the time as desired. set the time as desired. • The orange TIMER lamp ( ) will light up. • The orange TIMER lamp ( ) will light up. • The time setting will count down to show • The time setting will count down to show the remaining time.
• After “H” is indicated in the first second, power consumption is indicated. (When INSTANT LOW WATTAGE is set, “L1” or “L2” is dis- played first.) • During PLASMACLUSTER operation at FAN (AH-PNX21) mode and SELF CLEAN operation, power consumption will not be displayed. Maximum POWER CONSUMPTION •...
MAINTENANCE Be sure to disconnect the power cord from CLEANING THE UNIT AND THE RE- the wall outlet or turn off the circuit breaker MOTE CONTROL before performing any maintenance. • Wipe them with a soft cloth. CLEANING THE FILTERS • Do not directly splash or pour water on them. It can cause electrical shock or equipment Turn off the unit. damage. • Do not use hot water, thinner, abrasive pow- Remove the filters.
BEFORE CALLING FOR SERVICE The following conditions do not denote Check the following points before calling for equipment malfunctions service. UNIT DOES NOT OPERATE The unit does not operate The unit will not operate if it is turned on im- • Check if the circuit breaker has tripped or the mediately after it is turned off. The unit will fuse has blown. not operate immediately after the mode is changed.