Related Manuals for Haier HW60-0713S
Summary of Contents for Haier HW60-0713S
- Page 1 Twin-tub Washing Machine User's manual User's manual Twin-tub Washing Machine This manual is for HW60-0713S Please read this manual carefully before using. Special number:0030508674G Retain it for future reference.
-
Page 2: Table Of Contents
Contents Packing list The cover 2 Names of the parts Safety precautions Installation and adjustment Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting Answers to question Specification × ° Ï ä Ë µ Ã ÷ Packing list Quantity Name... -
Page 3: Names Of The Parts
¸ ÷ ² ¿ Î » Ã û ³ Æ Names of the parts Valve cover Meaning and description of the symbols Contents marked with that symbol are related Warning sign to the safety of the product and the personal safety of the users. -
Page 4: Safety Precautions
× ¢ Ò â Ê Â Ï î Safety precautions Please insert the power cord into When the machine is normally special receptacle with rated vol- using, please put the power plug tage.Be sure to use single-phase at the location easily to be insert- three pins receptacle.The earthing ed and extracted by hand. - Page 5 × ¢ Ò â Ê Â Ï î Safety precautions Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the rotation is slow. Take special care of the machine by yourself. children.
-
Page 6: Installation And Adjustment
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package,please take out the lint filter from the document bag,install it to the overflow filter of the wash tub.See to the figure. - Page 7 How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Soft item Extend the drain hose from the side of wash tub. Figure 1 Put soft items on the ground. Lean the machine down gently with the front surface facing the ground.
-
Page 8: Preparation Before Washing
Preparation before washing Ï ´ Ç ° × ¼ ± ¸ Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. -
Page 9: The Musts In Washing
The musts in washing Ï ´ µ Ó Ð ë Ö ª The capacity of washing and spinning of the machine refer to the weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the standard capacity. -
Page 10: Washing Sequence
Washing sequence Ï ´ µ Ó Ë ³ Ð ò Spin timer Wash selector Wash timer (To set to below 2 minute, (Strong current, (to set to below 1 minute, Water-filling entrance first set to 5 minute then standard current) first set to 2 minute then turn it back. - Page 11 Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper Proper The laundries No gland are slanting (2) Close the inner and outer cover of the spin tub.
- Page 12 Rinsing Rinse with stored water (Repeat the midway spinning and rinsing with stored water for 2-3 times) 1. Put the laundries into the wash tub. Select suitable current according to the laundries. 2. Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing.
-
Page 13: Disposal After Washing
Ï ´ º ó ´ ¦ À í Disposal after washing After using, please clean the lint and eyewinker of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. - Page 14 Ï ´ º ó ´ ¦ À í Cleaning the overflow filter 2. Take off the corrugation pipe. Water level Dismantle the upper part of the adjusting lever corrugation pipe inside overflow filter ( as indicated in Corrugation Figure 1). Pipe 3.
- Page 15 Ï ´ º ó ´ ¦ À í protective cover Cleaning the 2.cleaning dirty under the protective cover take out the sundries using the plier or other wiry 3.install the protective cover after cleaning, install it as origin assure it reliable Disposal of the complete unit After washing, dismount the water inlet Wipe the complete unit with soft...
- Page 16 Trouble-shooting Answers to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.