Table of Contents
Advertisement
Available languages
Available languages
Ambient temperature
●
Temperature 0-35°C
●
Atmosphere 86-106 kpa
●
VOLTAGE:115V/60HZ
●
Put the water cooler on the horizontal ground. Leave an adequate space (10-20 cm)
●
behind the water cooler for good ventilation.
When using the bottles with pure water, remove the cap of the water bottle. Open the
●
water dispenser door, you can see a pipe.Then put the pipe into the water bottle, and
make sure the cap cover the bottleneck tightly, to avoid the water can't be pumped into
water tank.
Push the hot water tap, and bubbles are generated inside the bottle. It says that
●
water is flowing into hot water tank and cold water tank. Keep pressing the hot water
tap until water flows out. Cold water doesn't need particular adjustment.
Caution: Do not connect the electrical power plug, until water comes out of
●
the hot water tap.
After water flows out from the hot tap,power can be on, then the hot indicator on the
●
front panel will be on.
Turn the heating switch on, the red indicator on the front lights is on and the heating
●
system starts working, when the hot water comes up (86-95°C) or so, the red
indicator goes off. The heating system stops working, then it is on a warm keeping
status. When the hot water temperature is lower than 85°C, the heating system will
start to work again automatically.
Turn on the cooling switch, the cold indicator on the front panel is on. The cooling
●
system starts working when the cold water falls between 5-10°C (for compressor-
cooling). When the cooling indicator goes off, the cooling system stops working and
it is on a cold keeping status. When the cold water temperature goes up to 10℃,
the cooling system will work again atomically.
Since the temperature has already been adjusted before leaving the factory, it is
●
unnecessary for customer to set the temperature.
Turn on the heating switch and cooling water switch on.Then the heating and cooling
●
processes start working. When the heating indicator is red, the heating function is on.
When the hot water temperature reaches the set limit, the heating process starts
working automatically. When cooling indicator is green, the cold water starts working.
The cooling indicator will be off when the cold water temperature meets the default
temperature. The cooling indicator will be on when the process of cold water starts
working again. Turn on either the cold water switch or hot water switch, the process
can work separately.
Cold and hot water: when the red indicator lights on, the heating system works.
●
Wh e n t he red lights goes off, it is on a warm-keeping status. When the green
indicator light on, the cooling system works. When the green light goes off, it is on a
cold keeping status.
If device is not applied for a long time, after the hot water cools down, please
●
OPERATION
- Quick Links:
- Operation
- Maintenance
- Troubleshooting Guide
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the EFWC505 and is the answer not in the manual?
Questions and answers
The red light is flashing and no water will dispense. How can this be fixed?
water is not coming out replaced with new jug
Water may not be coming out of the Frigidaire EFWC505 after replacing the jug due to the following reasons:
1. Improper Tube Placement: The water tube may not be inserted tightly into the new bottle. Ensure the tube is properly placed and pressed tightly, or the pump may not function.
2. Water Shortage Lock: If both the shortage water tank and the bottle lack water, the machine locks, and the water shortage indicator light flickers while an alarm sounds for 30 seconds.
3. Door Not Closed: If the door is open, the pump stops working. Ensure the door is fully closed after replacing the bottle.
4. Air in the System: After replacing the bottle, air may be trapped in the water lines. Press the dispenser lever several times to release air and allow water to flow.
Check these factors to restore normal water flow.
This answer is automatically generated
The plastic part that connects to the metal rod that goes into the water jug is broken. How do I order that part or what is the part number?
My despenser is not heating or cooling the water and the red light is blinking
The Frigidaire EFWC505 water dispenser may not be heating or cooling the water and showing a blinking red light because of a "dry burn" condition. This happens when the heating switch is turned on without water in the tank. To fix this, unplug the power cord, wait for more than 1 hour, then plug it back in and fill the tank with water. This may allow the hot tank to work again.
This answer is automatically generated
I replaced the water bottle and now it will not **** the water up through the tube.
The Frigidaire EFWC505 may not be drawing water through the tube after replacing the water bottle because the water tube is not pressed tightly into the new bottle. If it is not secured properly, the pump may not be able to draw water into the water tank.
This answer is automatically generated
Frigidaire bottom load model number EFWC505keeps with red light then makes noise after water is replaced then beeps for a while and red light blinks.
The red light indicating that we need to change the water will not turn off even though we have changed the jug and it is full.
The red light on the Frigidaire EFWC505 indicates that the heating system is working. If it remains on after changing the water jug, it is likely because the dispenser is heating the water to reach the default hot temperature. This is normal operation and the red light will go off once the water reaches the desired temperature and switches to warm-keeping status.
This answer is automatically generated