Directed 5305 Installation Manual
  1. Manuals
  2. Brands
  3. Directed Manuals
  4. Automobile Accessories
  5. 5305
  6. Installation manual

Directed 5305 Installation Manual

Lcd 2-way and 1-way models security and remote start
Hide thumbs
Table of Contents

Advertisement

Quick Links

5305 and 5105
Installation Guide
LCD 2-way and 1-way models
Security and Remote Start
This product is intended for installation by a professional
installer only! Attempts to install this product by a per-
son other than a trained professional may result in severe
damage to a vehicle's electrical system and components.
© 2015 Directed, Vista, CA
N5X05 2016-01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5305 and is the answer not in the manual?

Questions and answers

Related Manuals for Directed 5305

Summary of Contents for Directed 5305

  • Page 1 This product is intended for installation by a professional installer only! Attempts to install this product by a per- son other than a trained professional may result in severe damage to a vehicle’s electrical system and components. © 2015 Directed, Vista, CA N5X05 2016-01...
  • Page 2 Bitwriter®, Code Hopping™, Doubleguard®, ESP®, Fail- Safe®, Ghost Switch™, Learn Routine™, Nuisance Preven- tion® Circuitry, Revenger®, Silent Mode™, Soft Chirp®, Stinger®, Valet®, VRS®, and Warn Away® are all Trade- marks or Registered Trademarks of Directed®. Bitwriter (P/N 998U) requires chip version 2.7 or newer to...

  • Page 3: Table Of Contents

    Contents Warning! Safety First ........................4 Wiring Diagram ..........................5 Wiring Connections ........................6 Main Harness, White 5-pin connector ..................6 Auxiliary/Shutdown/Trigger Harness, White 24-pin connector ............6 Remote Start, White 10-pin heavy gauge connector ..............7 Door Lock, White 3-pin connector ....................7 Wire Descriptions ...........................

  • Page 4: Warning! Safety First

    This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately.

  • Page 5: Wiring Diagram

    AUX/Shutdown/Trigger Polarity Jumper 24-pin Harness (-/+) Note: (+) or (-) light ash jumper needs to be installed for the appropriate light ash polarity and is found taped to the outside on the main unit. © 2015 Directed. All rights reserved.

  • Page 6: Wiring Connections

    This wire not only activates the remote start, it can also be used to change feature options when pro- gramming. See Programming System Features. Important: NEVER connect 200mA low current outputs directly to a motor or high current device WITHOUT a relay. © 2015 Directed. All rights reserved.

  • Page 7: Remote Start, White 10-Pin Heavy Gauge Connector

    D2D Harness, Red 4-pin connector BLUE D2D - TX BLACK (-) GROUND GREEN D2d - RX (+) 12V Bitwriter/Directed SmartStart Harness, Black 3-pin connector (+) 12V ORANGE ESP 2 - RX/TX BLACK (+) 12V Wire Descriptions Main Harness, White 5-pin connector Black: (-) CHASSIS GROUND This wire is the unit’s source of ground.

  • Page 8: Auxiliary/Shutdown/Trigger Harness, 24-Pin Connector

    This wire can also be programmed to activate a defogger circuit in the vehicle (see © 2015 Directed. All rights reserved.
  • Page 9 Disarm wire in the vehicle. This output can be programmed on to activate with unlock trunk release and for a single or double pulse output (see OEM alarm Disarm options in Feature Menus for more detail). © 2015 Directed. All rights reserved.

  • Page 10: Remote Start Heavy Gauge Harness, 10-Pin Connector

    Pink/Black: IGNITION 2/ACCESSORY ISOLATION WIRE This wire is # 87A of the onboard 2nd Ignition/Flex Relay. This wire prevents having to use additional relays in vehicles which requires ignition switch isolation as shown in Tech Tip #1077. © 2015 Directed. All rights reserved.

  • Page 11: Door Lock, 3-Pin Connector

    (see Ign-controlled Locks, Door Lock Pulses, Door Lock Duration or Comfort Closure in Feature Menus for more detail). Note: The doors of the vehicle must be closed when turning the ignition ON for the ignition controlled door lock feature to work. © 2015 Directed. All rights reserved.

  • Page 12: Connecting The Doubleguard Shock Sensor

    When adding an additional Single or Dual Zone Sensor Additional Sensor Green Blue Additional Sensor Black Green Blue Black +12V Ground +12V 504D Doubleguard Shock Sensor Ground 504D Doubleguard Shock Sensor 5X05 5X05 Note: When triggered, the Green wire reports Zone 4 © 2015 Directed. All rights reserved.

  • Page 13: Adjusting The Doubleguard Shock Sensor

    2. After three seconds the status LED on the Control Center lights solid when a successful tach signal is learned. 3. Release the Control Center button. Note: When the analog or data tachometer is programmed, the main unit automatically enters the Tachom- © 2015 Directed. All rights reserved.

  • Page 14: Remote Start Shutdown Diagnostics

    WTS (Wait-to-start) input timed out Timer Mode error: Ignition is on or shutdown input is active when activating timer mode. Turbo Mode error: Turbo mode is programmed off, engine is not on or shutdown input is active. © 2015 Directed. All rights reserved.

  • Page 15: Pairing A Remote Control

    • With White/Blue (-) Activation Input: Each time this input is pulsed with a (-) the next available setting will be chosen. © 2015 Directed. All rights reserved.
  • Page 16 The learn routine exits if any of the following occurs: • The open door is closed. • The ignition is turned On. • There is no activity for 30 seconds. • The Control Center button is pressed too many times. © 2015 Directed. All rights reserved.

  • Page 17: Feature Menus

    Feature Menus Default settings are in bold type. Menu 1 - Basic Menu One-chirp setting Two-chirp and up setting Item System Arming Mode: Active Arming Passive Arming Arm/Disarm Chirps: On Ignition Controlled Lock: On Ignition Controlled Unlock: On Door Locking Mode: Active Passive Panic with Ignition: On Door Lock Output Duration (in seconds): 0.8 sec.
  • Page 18 6. Panic With Ignition On: 1. Panic with ign On: The Panic output can be activated at any time. 2. No panic with ign On: The Panic output can be activated only when the ignition is off. 7. Door Lock Output Duration: 1.

  • Page 19: Menu 2 - Descriptions

    Menu 2 - Advanced Menu One-chirp setting Two-chirp and up setting Item 60 second* Siren Duration: 30 second NPC (Nuisance Prevention Circuitry): On Progressive Door Trigger: On Valet Switch Pulse Count: 1 2-5 pulses Door Trigger Error Chirp: On Ignition Controlled Domelight: On 2 pulses Unlock Output: 1 pulse 2 pulses...
  • Page 20 7. Unlock Output (Blue wire on 3-pin harness): 1. 1 pulse: The unlock output pulses once. 2. 2 pulses: The unlock output pulses twice. 8. Lock Output (Green wire on 3-pin harness): 1. 1 pulse: The lock output pulses once. 2.

  • Page 21: Menu 3 - Remote Start

    6. 2nd Ignition/Accessory Output (Pink/White on the 10-pin harness): • This will allow the Pink/White wire to be used as a 2nd ignition or an accessory. The default is 2nd ignition. © 2015 Directed. All rights reserved.
  • Page 22 The Temperature Start Mode will exit after 18 hours. 13. Short Engine Runtime/Turbo Mode: 1/3/5/10 Minutes: When Turbo Mode is activated, the engine will run for the duration set per the • selected option. © 2015 Directed. All rights reserved.

  • Page 23: Bitwriter - Only Options

    Bitwriter - Only Options If programming with the Bitwriter, the Learn Routine can be locked or unlocked. If the Learn Routine has previously been locked, it must be unlocked with Bitwriter - this cannot be done manually with the Control Center button. The Bitwriter gives you access to a wider range of system options.

  • Page 24: Reset And Deletion

    The Reset and Delete mode exits if any of the following occurs: • The open door is closed. • The ignition is turned off. • There is no activity for 30 seconds. • The Control Center button is pressed too many times. © 2015 Directed. All rights reserved.

  • Page 25: Security Features Disable/Enable

    Refer to Table of Zones for more information. Note: The Warn Away triggers are not stored to memory and is not reported. © 2015 Directed. All rights reserved.

  • Page 26: Table Of Zones

    Reducing the sensitivity can solve this problem. Door locks operate backwards. • This unit has easily-reversed lock/unlock outputs. Recheck wire connections to see if you have re- versed these. © 2015 Directed. All rights reserved.

  • Page 27: Troubleshooting: Remote Start

    The vehicle starts, but will only run for 10 seconds: 1. Is the remote start programmed for voltage sense? If this does not work, a tach wire should be © 2015 Directed. All rights reserved.
  • Page 28 2. If the vehicle has an electronic climate control system some will reset when the key is turned off and then back on, unfortunately this is a function of the vehicle and cannot be bypassed. © 2015 Directed. All rights reserved.

This manual is also suitable for:

5105

Table of Contents

Save PDF