Hawksmoor CS2500A-3 Original User Instructions
  1. Manuals
  2. Brands
  3. Hawksmoor Manuals
  4. Chainsaw
  5. CS2500A-3
  6. Original user instructions

Hawksmoor CS2500A-3 Original User Instructions

25.4cc petrol chain saw
Hide thumbs

Advertisement

Table of Contents

Original User's Instructions
25.4cc Petrol Chain Saw
SKU: 23253
WHAT'S IN THE BOX
Chain saw x 1
Brake cover x 1
PLEASE KEEP THESE INSTRUCTIONS FOR FURTHER REFERENCE
Bar cover x 1
Oregon chain x 1
Oregon bar x 1
If you do not have all these items, please contact:
www.coreservice.co.uk
Hotline: +44 01904 947568
Email support@coreservice.co.uk
Fuel bottle x 1
Hex key x 1
Socket wrench/ slotted
screw drive x 1
Screw driver x 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CS2500A-3 and is the answer not in the manual?

Questions and answers

Kevin Sanders
March 23, 2025

Idle speed to fast

0

Related Manuals for Hawksmoor CS2500A-3

Summary of Contents for Hawksmoor CS2500A-3

  • Page 1 Original User’s Instructions 25.4cc Petrol Chain Saw SKU: 23253 WHAT'S IN THE BOX Chain saw x 1 Bar cover x 1 Fuel bottle x 1 Oregon chain x 1 Hex key x 1 Socket wrench/ slotted screw drive x 1 Screw driver x 1 Oregon bar x 1 Brake cover x 1...

  • Page 2: Specification

    SPECIFICATION Technical Data Model CS2500A-3 Type of the engine RY1E34FC Displacement 25.4cm Power 0.7kW Max.engine speed 11000min Idling speed 3300±300 Max.chain speed 21m/s Volumes of oil tank 160cm Volumes of fuel tank 230cm Net weight 3.8kg Oil ratio 40(fuel):1(oil) Cutting length 200mm (10”),...
  • Page 3 EXPLANATIONS AND SYMBOLS, CAUTIONS AND WARNINGS Explanations of symbols Before any use, refer to the corresponding paragraph in the manual. This symbol, before a safety comment, indicates a precaution, a warning or a danger. Ignoring this warning can lead to an accident for yourself or for others. To limit the risk of injury, fire, or electrocution, always apply the recommendations indicated.
  • Page 4 Guaranteed sound power level data (113dB), in accordance with Directive 2000/14/ Beware of kickback (recoil). Avoid contact with the tip of the guide bar (chain return point). This will result in kickback of the chainsaw. DO NOT hold the saw with one hand. Hold the saw frmly with both hands.

  • Page 5: Health And Safety

    HEALTH AND SAFETY GENERAL SAFETY WARNINGS Safety Warnings WARNING! Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. WARNING! Read all safety warnings and instructions designated by the symbol. Save all warnings and instructions for future reference.

  • Page 6: Operation

    caused by improper or incorrect usage. PLEASE NOTE: Our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the machine is used in commercial, trade or industrial businesses or for the equivalent purposes. PREPARATION •...
  • Page 7 incomplete or loosely assembled. Make sure that the chain rotation stops when the chain brake is applied. • Shut off the engine before setting the chainsaw down. • Use extreme caution when cutting small bushes and saplings; slender material may catch in the saw chain and be whipped towards you or pull you off balance.
  • Page 8 firewood, etc. It is not designed for lengthy use. If it is used for a lengthy period, the vibrations it causes in the hands of the user may result in circulation problems (white finger syndrome). • The chain is designed exclusively for sawing wood. You may only fell trees if you have received the appropriate training.
  • Page 9 reduce kickback and maintain control of the saw. Never let go of the chainsaw when it is running. • Make sure that the area in which you are cutting is free from obstructions. Do not let the nose of the chain bar contact a log, branch, or any other obstruction which could be hit while you are operating the saw.

  • Page 10: Maintenance And Storage

    MAINTENANCE AND STORAGE • Keep all nuts, bolts and screws tight, to be sure the equipment is in safe working condition. • Never store the equipment with petrol in the tank inside a building where fumes can reach an open flame or spark. •...
  • Page 11 COMONENT LIST 1. Chain brake 2. Handle 3. Safety trigger lock 4. Starter 5. Oil tank 6. Fuel tank 7. Oregon chain saw 8. Prime bulb 9. Top handle 10. Ail filter cover Not all the accessories illustrated or described are included in standard delivery.

  • Page 12: Assembly And Use

    ASSEMBLY AND USE INTENDED USE a. Assembly of the chain guide IMPORTANT: The machine must not be started during assembly. Wear protective gloves when handling the blade. 1) Pull the guard toward the front handle to check that the chain brake is not engaged. 2) Loosen the nuts and remove the chain cover.

  • Page 13: Filling The Fuel Tank

    9) Tighten the nuts and check if the chain is rotated correctly and tight. While lifting the chain guide, turn the content screw to apply correct tension to the chain. Then lock the crankcase nuts. Rotate the chain with your hand to check that it is turning without excessive resistance and that it is properly tightened.
  • Page 14 The recommended mixing ratio is 40:1 (make sure the mixing ratio is correct before filling the product. a. Mixing ∫ Mix in a clean, empty container (supplied). ∫ Pour the oil into the container. ∫ Pour the fuel into the tank. Mix the mixture long enough (more than one minute) to get a good combination.
  • Page 15 1. Starting the engine a. Press the priming pump continuously until the fuel enters the pump. Set the switch to position I. b. Pull the starter chock nob. The starter will close and the throttle will be moved to the starting position Hold the chainsaw firmly against the ground.
  • Page 16 2. Stopping the engine Allow the chainsaw to run for a few minutes. Then turn the switch to the OFF position. 3. Main settings a. Adjusting the carburetor The carburetor is preset at the factory. To avoid malfunction, it is recommended not to adjust the adjustment screws. If these screws require readjustment, have the machine serviced by your service center.
  • Page 17 ∫ Start the engine and grasp the handle firmly with both hands. ∫ While pulling the throttle control lever to keep the chain in operation, push the brake lever down with the back of the left hand. ∫ When the brake is running and the chain is stopped, remove the hand from the throttle.
  • Page 18 4. Work with wire and harness NOTE: It is necessary to have a complete training before working at high. It is strongly recommended that only experienced and trained persons carry out work at high. Know all emergency procedures to be carried out. These instructions are examples of good practice.
  • Page 19 forces on their working position, good support may be sufficient to maintain a safe working position. However, as operators move away from the trunk, they will need to take steps to suppress or neutralize increasing lateral forces, for example by redirecting the main rope through an additional anchor point or using an adjustable strap directly from the harness Has an additional anchor point.
  • Page 20 Operators should: - Never cut with the rebound area at the end of the chain saw chain guide - Never hold and cut sections or - Never try to catch sections when they fall. e. Release of a jammed saw If the saw gets stuck during cutting, the operators should: - Saw the saw and attach it securely to the cutting foot of the shaft (ie trunk side) or has a separate chord from the tool...
  • Page 21 c. Trunk in elevation Begin by cutting a first part from below and then from above. Then, on the second part, repeat this operation. f. Pruning of a felled tree Observe first the direction of flexion of the branch. Make a first notch on the side in flexion and finish the cut on the opposite side.
  • Page 22 MAINTENANCE AND STORAGE 1. Maintenance Before any maintenance work, the machine must be switched off and completely cooled. Perform the maintenance work according to the instructions below and perform them regularly. A clean, well-maintained machine increases its standard of living and efficiency. On the contrary, a machine maintained can cause damage, accidents and render the tool inoperable in the short term.
  • Page 23 d. Cleaning the oil filter and fuel filter Clean these items regularly. Remove them from the tanks using clamps. Clean them with gasoline and then put them back in place afterwards e. Guide bar Cleaning: Remove bar guide to remove dirt from grooves and oil inlet.
  • Page 24 f. Sprocket Check the sprocket on signs of wear. If wearing is important, replace it with a new one. Do not install a chain on a worn or damaged sprocket. Do not install a worn chain on a pinion. g. Spark plug Clean the electrodes with a wire brush and set the gap to 0.6mm if necessary.
  • Page 25 The chain saw must be switched off and locked before sharpening. Use a round file or sharpening device (see in store). Place the file on the tooth and push straight. Shift with the same movement. After sharpening all teeth, check if the teeth are sharp. 2.

  • Page 26: Troubleshooting

    TROUBLE SHOOTING Use this section to help you to try and solve any problems you may have Fault Possible Cause Solution Unit won’t start or 1. Incorrect starting procedures 1. Follow instructions in the user starts but will not run guide or refer to the starting 2.
  • Page 27 NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR PRODUCT, PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HPRODUCT YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT US BY REFERRING TO THE SERVICE & SUPPORT INFORMATION ON THE FOLLOWING PAGE.
  • Page 28 DECLARATION OF CONFORMITY / PERFORMANCE Product Code: 23253/CS2500A-3 Product Description: Hawksmoor 25.4cc 34cm Top Handle Petrol Chainsaw 1. Toolstation Limited, Express Park, Bristol Road, Bridgwater, Somerset TA6 4RN This declaration of conformity is issued under the sole responsibility of Toolstation 2.

  • Page 29: Environmental Information

    ENVIRONMENTAL INFORMATION When your product comes to the end of its life or you choose to update or upgrade it by replacing it, please do not dispose of it with your normal household waste. Please recycle where facilities exist. When you need to dispose of this product, check with your retailer or local authority for suitable options.

  • Page 30: Customer Support

    GUARANTEE Toolstation products deliver reliable service for normal, household use in domestic settings. All Toolstation products are individually tested before leaving the factory. If you are a consumer and you experience a problem with your Toolstation product, which is found to be defective due to faulty materials or workmanship within the Guarantee Period, this Toolstation Guarantee will cover repair or - at the discretion of Toolstation –...

This manual is also suitable for:

23253

Table of Contents