Related Manuals for BIANCO PUMPZ PTFINOX45S2NXT
Summary of Contents for BIANCO PUMPZ PTFINOX45S2NXT
- Page 1 ntroller Pumps INOX45 808393 INOX60 808394 INOX90 808395 FERRO60 808397 PTF 808396...
-
Page 2: Introduction
1. Introduction Congratulations on your purchase of Bianco Pumpz pump. Bianco Series 2 offers performance, reliability and dependability. This manual is for the Jet types Inox (stainless steel) and Ferro (cast iron) pumps as well as for the PTF (peripheral turbine type) model. -
Page 3: Table Of Contents
3. Contents 1. Introduction ......................2 2. Key Features......................2 3. Contents ....................... 3 4. ISO 7010 Symbols used in this manual .............. 3 5. Warnings ....................... 4 5.1 Cautions ......................5 6. Standards and Approvals ..................5 7. Technical Specifications..................6 8. -
Page 4: Warnings
5. Warnings Read the manual carefully before starting and retain for future reference. Prior to starting installation or any maintenance the pump must be disconnected from the power supply and pressure relieved from the system including controller, pump and associated pipework. Any changes or modification to the wiring must be carried out by suitably qualified personnel. -
Page 5: Cautions
5.1 Cautions 5.1.1 Protect the pump and controller from rain and moisture and minimise exposure to extremes of heat and cold. Operating range 2 C - 40 5.1.2 The pump is designed for use with clean water. Contamination including sand or mineral deposits may affect the operation of the pump and controller. -
Page 6: Technical Specifications
7. Technical Specifications SPECIFICATIONS ITEM CODE 808393 808394 808395 808397 808396 BIA- BIA- INOX45S2NXT INOX60S2NXT INOX90S2NXT FERRO60NXT PTF37NXT Maximum head Maximum 50 lpm 58 lpm 70 lpm 58 lpm 37 lpm flow Pump Start Preset 2.2 bar pressure Pump stop Flow less than 0.5 lpm Input power - 240V... -
Page 7: Electrical Connections
8. Electrical Connections Always use an electrical outlet that is protected by Residual Current Device (RCD) Safety Switch with a trip current of 30mA or less. A Safety Switch is required by Australian/New Zealand Standard AU/NZS 60335.1-2011. The pump is supplied with a 10 amp rated lead and AS/NZ 3112 (Type I) 3 pin male power plug for connecting to mains power. -
Page 8: General Installation Notes
9. General installation notes Review Section 5 - Warnings and 5.1 - Cautions prior to installing Choose a pump location with a firm base as close to your water source as possible and close to a suitable power supply. Avoid extension cords. If an extension cord must be used ensure it is correctly rated. -
Page 9: General Intake (Suction) Piping Notes
10. General intake (suction) piping notes The intake suction piping is the most critical part of the installation. Errors or air leaks will cause significant issues for performance and pump reliability. Reminders of best practice: Pipe size must be equal to or larger than the Air Pocket inlet port size (see Section 13) Inlet piping as short and straight as practical... -
Page 10: Boosting Mains Supply Or Connecting To A Hot Water System
11. Boosting mains supply or connecting to a hot water system Boosting Mains supply Connecting any of these pumps directly to mains water supply is not recommended. If mains pressure is poor, best practice is to install an isolating (break) tank. Use the guidelines in Section 12 or 13 depending whether the water from the tank will be above or below the pump inlet. -
Page 11: Water Supply Above The Pump Inlet (Flooded Suction)
12. Water supply above the pump inlet (flooded suction) Review SECTION 6 and 6.1 (Warnings and Cautions) prior to installation Reminders of best practice Fit a valve to isolate the tank If the suction line is quite long fit another valve close by the pump Non Return Valve in suction line recommended Avoid pipework which could trap air Potential air trap... -
Page 12: Water Supply Below The Pump Inlet (Suction Lift)
13. Water supply below the pump inlet (suction lift) not recommended for suction lift applications Reminders of best practice Suction pipes drawing upwards more than 1m require a foot valve and an intake screen. Ensure there is at least 300m of water above the intake at all times. Keep the intake screen at least 100mm above the bottom of the tank or well Avoid pipework which could trap air. -
Page 13: Priming And Operation
14. Priming and Operation Bianco Inxo and Ferro pumps are “self-priming” but this still means that the pump and delivery line MUST be manually primed (filled) before the pump is started for the first time to ensure the mechanical seal is well lubricated. Dry operation causes irreparable damage to the mechanical seal. -
Page 14: Warranties - Terms And Conditions
15. Warranties – Terms and Conditions This warranty is given in addition to the consumer guarantees found within the Australian Competition and Consumer Act 2010 (Cth) for goods purchased in Australia and the Consumer Guarantees Act 1993 NZ for goods purchased in New Zealand: 1) White International Pty Ltd / White International NZ Ltd (White International) warrant that all products distributed are free from defects in workmanship and materials, for their provided warranty period as indicated on the top or opposite side of this document. -
Page 15: Trouble Shooting Guide
16. Trouble Shooting Guide POSSIBLE CAUSE POTENTIAL SOLUTIONS The pump won’t No electricity Check the power supply. Is the power LED on the start and makes no controller illuminated? noise Fuses or RCD tripped Fuses or RCD tripped may indicate more serious problems Internal motor fault Contact an expert to check the motor... - Page 16 www.whiteint.com.au www.whiteint.co.nz Please always refer to our website for further technical information & new product innovations Disclaimer: Every effort has been made to publish the correct information in this manual. No responsibility will be taken for errors, omissions or changes in product specifications. ©...
Need help?
Do you have a question about the PTFINOX45S2NXT and is the answer not in the manual?
Questions and answers