Download Print this page
Fujitsu Primergy RX600 Start Manual

Fujitsu Primergy RX600 Start Manual

Advertisement

Quick Links

n PRIMERGY RX600 S4 Manuals
Manuals for this server are stored in PRIMERGY Startup Disc. Insert the PRIMERGY Startup Disc and click [PRIMERGY Manuals] on the
[PRIMERGY Startup Disc] screen to refer to the manuals.
The manuals can be read using Acrobat
1
Checking the items
supplied
Check the contents in the package using
the "Contents List".
If any items are missing, contact an office listed in the
"Contact Information".
3
Installing internal options
If internal options have been purchased separately, install them before installing an operating system.
If you use Custom Made Service, installing internal options is not required. Just check "
installing an OS".
n Points to note before installing internal
options
Make sure to read the following manuals for operations.
"Chapter 6 Installing Internal Options"
"PRIMERGY Server Books"/"Supplement"
n Points to note before installing an OS
When using the optional devices listed below, note the fol-
lowing instruction before installing an OS.
- USB optional devices other than FDD
Install USB optional devices other than a floppy disk drive
after installing an OS.
- Internal Data Cartridge Drive Unit
Insert a data cartridge after installing an OS.
If a data cartridge is inserted, remove it.
- Optional external devices
- When hard disk units are installed in PRIMERGY SX35
with arrays configured, delete the array configuration.
After installing an OS, configure the arrays again.
- When connecting an external storage system such as
ETERNUS, do not turn on the power until the OS instal-
lation completes.
RX600 S4
Reader
or Adobe
Reader
®
®
®
. When using Acrobat
Reader
®
®
2
Reading and understanding
"Safety Precautions"
Before using this server, be sure to read and under-
stand the attached "Safety Precautions".
n Available internal options and installation
locations
������������������
������������������������
��������������������
��������������������������
After installing internal options, check that the order
and location of installation are correct and cables
are correctly connected.
1
B7FH-5691-01EN-00
, use version 5.0 or later.
®
n
Points to note before
���������������
��������������
���
�������������

Advertisement

loading

Summary of Contents for Fujitsu Primergy RX600

  • Page 1 B7FH-5691-01EN-00 RX600 S4 n PRIMERGY RX600 S4 Manuals Manuals for this server are stored in PRIMERGY Startup Disc. Insert the PRIMERGY Startup Disc and click [PRIMERGY Manuals] on the [PRIMERGY Startup Disc] screen to refer to the manuals. The manuals can be read using Acrobat...
  • Page 2 Conditions n Restrictions of installation locations To settle this server, avoid the following areas: ����������������������������� ����������������������������� ����������������������������������� ������������� ������������� ����������������������� ��������� ������������������������� ������������������������� ������������������������� ���������������������������������������� ���������������������������������������� ���������������������������������������� ���������������������������������������������� ���������������������������������������������� ���������������������������������������������� ���������������������������������������� ���������������������������������������� ���������������������������������������� ���������������������� ���������������������� ���������������������� ���������������������������������������������������� ���������������������������������������������������� ���������������������������������������������������� ����������������������������������������������������������� �����������������������������������������������������������...
  • Page 3: Connecting Peripheral Devices

    Pull the slide rails toward the front until Install the server in the rack cabinet. they click into place. Push the locks on the right and left of the slide rails to unlock them. Slide the server into the rack, push- ing it on so that the rear side of the server may float a little.
  • Page 4: Installing The Os

    "2.1.2 Hardware Settings", "Chapter 7 Configuring Hardware and Utilities" You can write down hardware configuration and setting values of the BIOS Setup Utility in the "Configuration Sheets" that is available from Fujitsu PRIMERGY website (http://primergy.fujitsu.com). Turn on the peripheral devices, such as Set the hardware.
  • Page 5 Select [Quick Installation], and click Click [Accept]. [Next]. After files are copied, a message prompts you to insert the Disc 2. The [Select the Boot Controller and Boot Disk] Insert the OS CD/DVD (Installation disc) Disc 2. window appears. After files are copied, a message prompts you to Set configuration of the RAID and disks, eject the CD/DVD and floppy disk.
  • Page 6 PRIMERGY information For the latest information on PRIMERGY, update modules, "Chapter 4 Operations after OS Installation drivers and the software, refer to the Fujitsu PRIMERGY - Set to collect memory dump website (http://primergy.fujitsu.com). Regarding BIOS and firmware, contact an office listed in the By setting to collect memory dump, debugging information "Contact Information".
  • Page 7 It is the customer's responsibility to maintain backup copies in advance. In case of data loss, Fujitsu assumes no liability for data maintenance or restoration and damages that occur as a result of the data loss for any reason, except for items covered under warranty.
  • Page 8: Contact Information

    Address: Level 1 & 2, No.3505 Jalan Technokrat 5, Cyberjaya, Selangor Darul Ehsan, Malaysia 63000 For the latest information, refer to the Fujitsu PRIMERGY website (http://primergy.fujitsu.com). Microsoft, Windows, Windows Server are registered trademarks of the Microsoft Corporation in the USA and other countries.