Related Manuals for Alumax Lani L-301X-24
Summary of Contents for Alumax Lani L-301X-24
- Page 1 L-301X-24, L-302X-24 L-301X-32, L-302X-32 L-421X-32, 422X-32 L-421TBX-32, L-422TBX-32 L002 08.10...
- Page 2 Please keep this manual and product code number for future reference and replacement parts ordering if necessary.
-
Page 3: General Instructions
2 PEOPLES REQUIRED GENERAL INSTRUCTIONS - Read this manual carefully and completely before proceeding. - It is recommended that you wear safety glasses at all times during the installation. INSTALLATION OVER CERAMIC TILES - Silicone should be used to seal the gap where the ceramic tiles meet the xed panel. -
Page 4: Parts Listing
INSTALLA TION MANUAL 301X-24, 302X-24 ARTS LISTING HARDWARE 13.1 WALL PLUG #6-1 13.2 SCREW #8-3/8 HINGE 13.3 SCREW #8-1 1/4 13.4 SCREW CAP 13.5 SPACING BLOCK HINGE I T E M P A R T S Q T Y D O O R P A N E L W A L L J A M B 3 . -
Page 5: Tools And Materials Required
INSTALLATION MANUAL 301X-24, 302X-24 TOOLS AND MATERIALS REQUIRED LONG NOSE LOCKING PLIER SCREWDRIVERS DRILL Ø1/4" & Ø1/8" DRILLBITS SILICONE 2" 1/2" 6" PENCIL CUTTING PLIER TAPE MESURE LEVEL MALLET BLOCK INSTALLA TIONS OF COMPONENTS Return panel Bottom clips Support bar see page 13-14 see page 9-10 Hinges... - Page 6 INSTALLATION MANUAL 301X-32, 302X-32 PARTS LISTING HARDWARE 13.1 WALL PLUG #6-1 13.2 SCREW #8-3/8 HINGE 13.3 SCREW #8-1 1/4 13.4 SCREW CAP 13.5 SPACING BLOCK HINGE I T E M P A R T S Q T Y D O O R P A N E L W A L L J A M B...
- Page 7 INSTALLATION MANUAL 301X-32, 302X-32 TOOLS AND MATERIALS REQUIRED LONG NOSE LOCKING PLIER SCREWDRIVERS DRILL Ø1/4" & Ø1/8" DRILLBITS SILICONE 2" 1/2" 6" PENCIL CUTTING PLIER TAPE MESURE LEVEL MALLET BLOCK INSTALLATIONS OF COMPONENTS Support bar Return panel Bottom clips see page 13-14 see page 9-10 Hinges Door panel...
- Page 8 INSTALLATION MANUAL 421X-32, 422X-32 PARTS LISTING HARDWARE 13.1 11.2 WALL PLUG #6-1 11.1 11.3 13.2 SCREW #8-3/8 HINGE 13.3 SCREW #8-1 1/4 13.4 SCREW CAP HINGE 13.5 SPACING BLOCK I T E M P A R T S Q T Y D O O R P A N E L A L L...
- Page 9 INSTALLATION MANUAL 421X-32, 422X-32 TOOLS AND MATERIALS REQUIRED LONG NOSE LOCKING PLIER SCREWDRIVERS DRILL Ø1/4" & Ø1/8" DRILLBITS SILICONE 2" 1/2" 6" PENCIL CUTTING PLIER TAPE MESURE LEVEL MALLET BLOCK INSTALLATIONS OF COMPONENTS Return panel Support bar Bottom clips see page 13-14 see page 9-10 Hinges Door panel...
- Page 10 INSTALLATION MANUAL 421TBX-32, 422TBX-32 PARTS LISTING HARDWARE 13.1 11.1 WALL PLUG #6-1 11.2 11.3 13.2 SCREW #8-3/8 HINGE 13.3 SCREW #8-1 1/4 13.4 SCREW CAP HINGE 13.5 SP ACING BLOCK I T E M P A R T S Q T Y D O O R P A N E L W A L L...
- Page 11 INSTALLATION MANUAL 421TBX-32, 422TBX-32 TOOLS AND MATERIALS REQUIRED LONG NOSE LOCKING PLIER SCREWDRIVERS DRILL Ø1/4" & Ø1/8" DRILLBITS SILICONE 2" 1/2" 6" PENCIL CUTTING PLIER TAPE MESURE LEVEL MALLET BLOCK INSTALLATIONS OF COMPONENTS Return panel Support bar Bottom clips see page 13-14 voir page 9-10 see page 9-10 Hinges...
- Page 12 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX RETURN PANEL INSTALLATION THIS INSTALLATION PROCEDURE APPLIES FOR ALL RETURN PANELS INSTALLATION REGARDLESS OF QUANTITY OR ADDITIONAL FIXTURE SUCH AS TOWEL BAR. Using a measuring tape, mark the center of the threshold of the base. Using the marking established in the previous step, run a second line up the wall.
- Page 13 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX CONTINUED 1e. Place the bottom clips (8) for return panel on the line traced previously following dimension shown on the plan view. Mark the screw location. Remove temporary the bottom clips to drill the base using #1/8”...
- Page 14 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX BOTTOM CLIPS INSTALLATION CORNER CLIPS INSTALLATION Fasten bottom clips (8) at both sides of the front panel (4) at approximately 3 ½” from the edges. FRONT PANEL holes Temporarily install the corner clip (6) on the slots panels (3 &...
- Page 15 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX CONTINUED Remove the front panel (4) by disassembling the corner clip back plate. Drill pilot hole on the base with Ø1/8” drill bit according to marking. Remove the bottom clips from the front xed panel (4).
- Page 16 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX SUPPORT BAR INSTALLATION 3a. Take apart the end component (A) of the support bar with the provided Allen Key WALL END COMPONENT 3b. Transfer the position of the bottom clip (8) to the back wall. At 82” from the threshold mark the position (center of the cylinder ) for the support bar end component (A) mounting...
- Page 17 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX CONTINUED Insert the clear gasket as shown. Then Loosen and rotate support bar to grab the front panel. CLEAR GASKET Level support bar. Tighten the set screws. INTERIOR SHOWER SIDE INTERIOR SHOWER SIDE...
- Page 18 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX GASKETS INSTALLATION 4a. Align the xed panel side gasket to the glass panel edge. Insert it with a 2” x 6” x INTERIOR 1/2” block and a mallet. Trim the excess SHOWER SIDE using the cutting plier.
- Page 19 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX HINGES INSTALLATION Fasten one side of the hinges (5) onto the xed panel (4). Do not tighten all the way for this step to allow other door (1) adjustments. INTERIOR SHOWER SIDE Place the door panel vertically next to the xed panel (4).
- Page 20 INSTALLATION MANUAL 421TBX, 422TBX TOWEL BAR INSTALLATION 6a. For 56305 - 56306 con gurations. If installation of return panel (11) has not been performed yet please, refer to step #1 to complete the installation. 6b. Install the towel bar (12) as illustrated.
- Page 21 INSTALLATION MANUAL 301X, 302X, 421X, 422X, 421TBX, 422TBX SILICONE SEAL THE SHOWER DOOR Seal the exterior of the shower along the wall with silicone. Fill gap between the glass panels and base surrounding the bottom clips (8). Inside the shower seal along the corner between the glass panels by passing trough the center of the corner clips with silicone.