Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TYROLIT Hydrostress TRE250
Summary of Contents for TYROLIT Hydrostress TRE250
- Page 1 Operating Instructions TBE400 Index 001 10999936 en / 04.01.2022...
- Page 2 Tel. +41 (0)44 952 18 18 Fax +41 (0)44 952 18 00 www.hydrostress.com TYROLIT Hydrostress AG reserves the right to make technical changes without prior notice. Copyright © 2018 TYROLIT Hydrostress AG, CH-8330 Pfäffikon ZH, Switzerland All rights reserved, in particular copyrighting and translating rights.
-
Page 3: Table Of Contents
TBE400 Owner manual text TABLE OF CONTENTS Contents……………………………... Safety precautions……………………….. General safety rules……………………… Health warnings…………………………... Unpack, assembly & set-up…………….. Diamond blade installation……………..Inspection & specification……………….. Features…………………………………… Cutting table assembly………………..…. The rip guide…………………………...…. Cutting depth……………………………... Water pump installation…………………. Folding legs ……………………………… Electric motor specifications……………. -
Page 4: Safety Precautions
SAFETY PRECAUTIONS Saw blade should be inspected daily for excessive wear, core cracks, and arbor damage. Replace any blade that shows signs of damage. • To mount blade, clean arbor and outer flanges, tightening nut securely. • DO NOT place any portion of body in line with blade while it is rotating. •... -
Page 5: General Safety Rules
GENERAL SAFETY RULES • Never use the machine improperly or work in an unsafe manner. • Always wear safety goggles, dust mask, and ear protection while operating the saw. • Always remain alert when the saw is in use. Failure to pay attention on the operator’s part may lead to serious injury. -
Page 6: Health Warnings
HEALTH WARNINGS Some dust are created by power sanding, sawing, grinding, drilling, and cause other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead based paints. •... -
Page 7: Inspection & Specification
INSPECTIONS & SPECIFICATION The compact TBE400 table saws are shipped completely assembled and ready for use except for the diamond blade. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. We are not responsible for any freight related damages. -
Page 8: Features
FEATURES The TBE400 table saw is designed for the professional contractor in mind. It enhances performance with a multitude of features facilitating operation. Sturdy handle and Spring Lever allow for quick pluge cuts Miter Cutting Capability Rear Splash Guard protects the jobsite against dust and water Stainless Steel Water Tray Folding legs with Wheels facilitate transport 45°... -
Page 9: Cutting Table Assembly
CUTTING TABLE ASSEMBLY To install the cutting table to the machine: 1. Set the cutting table on the rails 2. Install the screw and brackets to the cutting table 3. To remove the cutting table do the reverse of the above two steps. -
Page 10: The Rip Guide
THE RIP GUIDE Steps to use the 45º / 90º rip guide 1. Set the rip guide by positioning it on the desired dimension and tighten the threaded knob. Make sure that the rip guide is firmly tightened to avoid slippage. The rip guide can be used for 90º... -
Page 11: Water Pump Installation
WATER PUMP INSTALLATION 1. Remove the water pump from the box and check that it is not damaged. 2. Place the pump into the middle of the water tray along its side so that the water outlet is positioned horizontally. Connect the water hose from the blade guard to the pump and plug the power cord into the 3-prong receptacle. -
Page 12: Folding Legs
FOLDING LEGS... -
Page 13: Electric Motor Specifications
ELECTRICAL MOTOR SPECIFICATIONS Features: Power 2,2 kW Volts 230 V (110 V) Amps 10 Amps (20A) Motor RPM 2800 RPM Cycle 50 Hz (60 Hz) Recommendations: It is recommended that a 15 A (30 A) CIRCUIT be used while operating this saw. This will prevent any loss of power or interruption. -
Page 14: Do's & Don'ts For Blades
DO’S AND DON’TS FOR BLADES WET CUT BLADES DO'S • Inspect blades daily for cracks or uneven wear. • Always use appropriate blade for material being cut. • Inspect arbor shaft for uneven wear before mounting blade. • Always use blades with the correct arbor shaft size. •... -
Page 15: Saw Maintenance
SAW MAINTENANCE Maintenance interval Wath to do for maintenance and care After ecery use ot the Remove dirty water from container. machine Remove dirt and mud from the bottom of the container Rinse teh immersion pump with fresh water to prevent water pump dogging from residual dirt. -
Page 16: Troubleshooting
TROUBLESHOOTING Problem Possible cause Solution Machine does not run Power cord not properly Check that the machine is properly when switched on fixed / plugged in connected to the power supply. Power cord defective Have the power cord checked, replace if necessary. - Page 17 TROUBLESHOOTING Problem Possible Cause Solution Irregular run of the Poor tension in the blade Return the saw blade to the saw blade material manufacturer Saw blade wobbles Saw blade is damaged or Have the saw blade when running bent aligned/flattened Clean the receiving flange Solder the diamond segments of the old blade onto another swa...
- Page 18 TROUBLESHOOTING Problem Possible cause Solution Saw blade is blunt Saw blade type is Use appropriate type of saw blade unsuitable for the meterial being cut Saw blade type is unsuitable for the machine performance Saw blade too hard Diamond segments are Sharpen the diamond saw blade blunt Appearance of cut is...
-
Page 19: Customer Service
CUSTOMER SERVICE AFTER SALE SERVICE All customer service (technical questions, re-order of parts, etc.) will be provided by us. CLAIMS FOR LOST OR DAMAGED GOODS If merchandise is delivered in damaged condition or cartons are missing, a notation must be placed on all papers signed by the receiver. If unreported or concealed damages are noticed after delivery, the carrier should be contacted by telephone and if carrier fails to send an inspector within five days, a request should be made in writing to the carrier, confirming the telephone request for an inspection. -
Page 20: Disposal
DISPOSAL GENERAL The operator can recycle or dispose of the Table saw himself provided he observes the statutory provisions. In order to dismantle the Table saw correctly and to properly remove the materials some knowledge in the area of mechanics and knowledge about differentiation of waste materials is necessary. - Page 21 DISPOSAL OF TABLE SAW DISPOSAL REGULATIONS The dismantled parts of the table saw are sorted by material and sent separately to the appropriate collection points. Ensure that the following parts in particular are properly disposed The Table saw consists of the following materials: Cast aluminium Rolled aluminium products Bronze...
-
Page 22: Spare Parts List
SPARE PARTS LIST View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE P13400/1 10999945 Frame assy Rahmen kpl. P13400/2 10999946 Cutting table assy Schneidtisch kpl. P13400/3 10999947 Corss beam assy Querträger kpl. P13400/4 10999948 Cutting head assy Schneidkopf kpl. 10999949 Leg assy Beine kpl. - Page 23 View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE 10999955 Drain plug assy Ablassstopfen kpl. 10981941 Drain plug Ablassstopfen 10981943 Chain 170mm Kette 170mm P13401/1 10994556 Washer M4 4.3/9/0.8 U-Scheibe M4 4.3/9/0.8 10999995 Sheetm. screw dia 4.2x19 Blechschraube Dm 4.2x19 10995471 Hex.
- Page 25 View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE 11001882 Cutting table rub. matted Schneidtisch m.Gummimatte 11001883 Cutting table Schneidtisch 10999960 Rubber mat 404x129 Gummimatte 404x129 P13402/1 10999961 Rubber mat 404x124 Gummimatte 404x124 10999962 Rubber mat 404x40 Gummimatte 404x40 10999963 Rubber mat 404x70 Gummimatte 404x70...
- Page 27 View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE P13403/1 10986218 Splash guard holder Spritzschutzhalter P13403/2 971848 Hexagon nut M10 Mutter 6kt. M10 P13403/3 10987388 Washer M16 17/34/4 U-Scheibe M16 17/34/4 10981937 Angle locking handle Arretiergriff 10999970 Special nut M16 Spezialmutter M16 P13403/4 10999971...
- Page 28 View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE P13404/1 10999974 Water system assy Wasserführung kpl. 10999975 Hose Ø7.5/12.5x480mm Schlauch Ø7.5/12.5x480mm 10999976 Y distributor Y-Verteiler 10999977 Water tap assy Wasserventil kpl. 10999978 Hose Ø10/14x1850mm Schlauch Ø10/14x1850mm P13404/2 10999975 Hose Ø7.5/12.5x480mm Schlauch Ø7.5/12.5x480mm P13404/3...
- Page 29 View / Pos. TYHS code TYHS description EN TYHS description DE 10999977 Water valve assy Wasserventil kpl. P13404/4 10992413 Ball valve 1/4" f/f Kugelhahn I1/4" I1/4" 10999979 Adapter 1/4" Adapter 1/4" P13404/5 10999978 Hose Ø10/14x1850mm Schlauch Ø10/14x1850mm 10999980 Switch 230V/50Hz assy Schalter 230V/50Hz kpl.
- Page 30 View / Pos. TYHS code TYHS description EN TYHS Beschreibung DE 10999989 Motor fan cover assy Motorlüfterdeckel kpl. P13405/1 10997706 Fan cover Lüfterabdeckung 10999994 Lenshead screw M5x30 Linsenschr. KS M5x30 P13405/2 10997705 Lüfter 10999991 Flange assy Flansch kpl. 10999992 Inner flange Innenflansch P13405/3 10999993...
Need help?
Do you have a question about the TRE250 and is the answer not in the manual?
Questions and answers