Beko DIT25401 Installation Manual
Hide thumbs
Also See for DIT25401:
- User manual (47 pages) ,
- Installation manual (31 pages) ,
- Installation manual (29 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Beko DIT25401
Summary of Contents for Beko DIT25401
- Page 1 Dishwasher Installation Manual DIT25401 DIT38530 DDN25401X DDT38530XWS DIN25401 DIT39432 DUT25401W DDT39432X DUT25401X DDT39432CF DUT25401B DDT39432XIH DDT25401W DDT38530BX DDT25401X DDT36430X DDT25401B DDT36430XIH DDT38530X Document Number : 15 9889 0100_AD_BEKO_USA/ 03-08-18.(13:11)
- Page 2 Dishwasher Installation Manual DIT25401 DIT38530 DDN25401X DDT38530XWS DIN25401 DIT39432 DUT25401W DDT39432X DUT25401X DDT39432CF DUT25401B DDT39432XIH DDT25401W DDT38530BX DDT25401X DDT36430X DDT25401B DDT36430XIH DDT38530X Document Number : 15 9889 0100_AD_BEKO_USA/ 03-08-18.(13:11)
-
Page 3: Table Of Contents
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1. IMPORTANT SAFETY INSTRUCTIONS 1.1 INSPECT THE DISHWASHER 2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED 4. -
Page 4: Introduction
INTRODUCTION NOTICE : Please read this installation manual Read these installation instructions and particularly the safety instructions completely before installing and follow completely and carefully. They will save you them carefully. Save these installation time and effort and help to ensure optimum instructions and pass them on to any dishwasher performance. -
Page 5: Inspect The Dishwasher
If the dishwasher is installed in a NOTICE : • location that experiences freezing The dishwasher drain hose must be • temperatures (e.g. in a vacation home, installed with a drain loop at least cabin, etc.), you must drain all the 28”... -
Page 6: Tools Which May Be Needed
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Elbow with 3/4” N.P.T. female thread for dishwasher side, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other side. -
Page 7: Materials Supplied
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED 4.4 DISHWASHER PARTS BAG 2 Parts for your dishwasher will come in several plastic bags. (MODEL DEPENDING) Check your parts bags shown In addition to the manual bag to make sure you have all the and the dishwasher parts bag parts as listed to the left. -
Page 8: Dishwasher Specifications
5. DISHWASHER SPECIFICATIONS TALL TUB MODELS STANDART TUB MODELS... -
Page 9: Technical Features
5.1 TECHNICAL FEATURES Permissible water 4.35 - 145 psi (0.3 - 10 bars) pressure 120 V (volts), 12 A (amps), 60Hz (hertz) Electrical connection 1400 W (watts) Total power 1100 W (watts) Heater power NOTICE : Because we continually strive to improve our products, we may change our specifications and design without prior notice. -
Page 10: Enclosure Preparation
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS e-f) STANDART TUB MODELS... - Page 12 (+50mm) WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury. TALL TUB MODELS ONLY Tighten the plugs on both sides of your machine (v)
-
Page 13: Adjusting Height
Place the two mounting brackets into the top corners of the dishwasher. Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied. Bend sides of mounting brackets (B) in order to fix from sides (if necessary). 6.3 ADJUSTING HEIGHT If the height of the enclosure is 337/8”... -
Page 14: Installing The Side Trim Strips
6.4 INSTALLING THE SIDE TRIM STRIPS Remove the adhesive tape (Figure A). Place the trim strips on the front edge of the side walls (Figure B). NOTICE : Make sure you use the correct trim strip since there is a left and right side strip. The •... -
Page 15: Drain Preparation
WARNING Installation should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty. If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin etc.), you must drain all the water from the dishwasher’s interior. -
Page 16: Steam Protection Foil
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with... -
Page 17: Placement Of Dishwasher Into The Opening
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. - Page 18 7.1.2 WATER SUPPLY CONNECTION Do not use any extension cord or • Water supply may be connected to the portable outlet device to connect the dishwasher in one of two ways: dishwasher to a power supply. With metal braided hose. •...
- Page 19 WARNING Improper connection of the equipment- grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance, if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
-
Page 20: Readjusting Foot Levels
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. - Page 21 TALL TUB MODELS ONLY Open the fixing part on the Toe Kick(p). (A) Place it on the slots, which are on the brackets fixed before, and adjust the height (max. 40 mm). (B) Close the fixing part on the Toe Kick. (C)
-
Page 22: Fixing The Cabinet To The Counter
7.4 FIXING THE CABINET TO THE COUNTER STANDART TUB MODELS... - Page 23 TALL TUB MODELS...
-
Page 24: Preparing The Timber Door
7.5 PREPARING THE TIMBER DOOR Mid. Point Mid. Point Weight (max) 9 Kg / 19 lbs Height (h) : Height of the wooden door 30” (760mm) Tall Tub Models Only Height (h) : Height of the wooden door 28” (720mm) Standart Tub Models Only Width (w) : 23 ¼”... -
Page 25: Preparing The Product Door
7.6 PREPARING THE PRODUCT DOOR... -
Page 26: Installing The Timber Door
7.9 INSTALLING THE TIMBER DOOR 7.10 FIXING THE TIMBER DOOR... -
Page 27: Fixing The Timber Door
7.11 FIXING THE TIMBER DOOR Ø 4 x 36mm 7.12 ADJUSTING THE KICK PLATE • Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). • If the door hits the toe kick cut the necessary section out of the toe kick (B). -
Page 28: Connection
7.13 CONNECTION ~ 1500 ~ 1800 ~ 2000... -
Page 29: Installer Checklist
8. INSTALLER CHECKLIST Remove drain hose from disposal • making sure plug is removed. Your installer must have completed and checked the following: NOTICE : The dishwasher is square and level. • If your dishwasher is not operating • The dishwasher is fastened securely •...