Table of Contents
Advertisement
Quick Links
READ AND SAVE THESE INSTRUCTIONS
Ceiling Fan Owner's Manual
CF921BS00 -
CF921CK00 -
CF921GES00 -
CF921ORB00 -
CF921VNB00 -
Net Weight:
Part No. F40BP74330001
AVANT ECO
Model Numbers
16.6
Lbs.
Brushed Steel
Chalk
Golden Espresso
Oil Rubbed Bronze
Venetian Bronze
54", 60" or 72" Fan Blades
™
Not Included
Form No. BP7433-1
ETL Model No.: CF921
Advertisement
Table of Contents
Related Manuals for Emerson AVANT ECO CF921BS00
Summary of Contents for Emerson AVANT ECO CF921BS00
- Page 1 READ AND SAVE THESE INSTRUCTIONS ™ AVANT ECO Ceiling Fan Owner's Manual Model Numbers CF921BS00 - Brushed Steel CF921CK00 - Chalk CF921GES00 - Golden Espresso CF921ORB00 - Oil Rubbed Bronze CF921VNB00 - Venetian Bronze 54”, 60” or 72” Fan Blades 16.6 Net Weight: Lbs.
- Page 2 WARNING: To reduce the risk of fire or electric shock, this fan should only be used with fan speed control, Model No. FR-7861LMBG manufactured by Rhine Electric Co., Ltd. WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not specifically approved for this fan.
- Page 3 EMERSON QUICK START GUIDE The Quick Start Guide covers the installation WARNING instructions common for ceiling fan operations. If additional assistance with wiring, alternate hanging To reduce the risk of fire, electric shock, or personal systems, or lighting options, proceed to the complete injury, mount fan to outlet box marked “Acceptable for Fan...
- Page 4 LISTED WIRE (NEUTRAL) CONNECTOR (3) NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner’s Manual for wiring. 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied. Securely connect...
-
Page 5: Unpacking Instructions
Emerson Electric Co. could result in personal The upper foam pad serves as a holder for the fan injury or property damage. -
Page 6: Electrical Requirements
Electrical Requirements Your new ceiling fan will require a grounded electrical WARNING supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and Turning off wall switch is not sufficient. To avoid capable of withstanding a load of at least 50 pounds. - Page 7 How to Put Your Ceiling Fan Together (continued) 3. Make sure the grommet is properly installed in the coupling cover, then slide the coupling cover on the SETSCREW DOWNROD downrod until it rests on the motor housing. Place the ceiling cover over the downrod. Be sure that HANGER BALL the ceiling cover and the coupling cover are both...
- Page 8 How to Put Your Ceiling Fan Together (continued) 11. Remove the four switch housing mounting SWITCH screws (Figure 7) from the switch housing plate. HOUSING Position the switch housing assembly on the ASSEMBLY switch housing plate and align the holes in the switch housing assembly with the holes in the plate.
-
Page 9: How To Hang Your Ceiling Fan
How to Hang Your Ceiling Fan CEILING WARNING The fan must be hung with at least 7' of clearance from floor to blades (Figure 8). AT LEAST WARNING FLOOR The outlet box and joist must be securely mounted and Figure 8 capable of supporting at least 50 lbs. -
Page 10: How To Wire Your Ceiling Fan
Securely connect wires with wire OMITTED FOR CLARITY. connectors supplied. NOTE: If you are using an Emerson Light Fixture with your fan, see Light Fixture Owner’s Manual for wiring. 2. Securely connect the fan motor white wire to the supply white (neutral) wire using wire connector supplied (Figure 11). - Page 11 COVER Preset Memory Feature Figure 13 Your Emerson receiver is equipped with a preset memory feature. If the AC supply to the receiver is powered through a wall switch, when the switch is turned OFF, the control will remember the light intensity and fan speed.
-
Page 12: High Speed Conditioning Of Fan Control
Operation of Your Remote Control 5. To vary the intensity of the light, hold the DN or UP WARNING button down until the desired light intensity is reached, then release the button. Fan installation must be completed, including the installation of the fan blades, before testing 6. -
Page 13: Optional Accent Kit Installation
Optional Accent Kit Installation CAUTION: To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing light kit assembly. COUPLING COVER COUPLING COVER 1. Remove the three coupling cover screws and slide SCREWS (3) (RETAIN FOR LATER the coupling cover up the downrod for installation INSTALLATION) -
Page 14: Maintenance
4. Ceiling Fan Blades (see store or catalog). Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal WARNING injury or property damage. The use of any other control not specifically approved for this fan could result in fire, shock and personal injury. -
Page 15: Troubleshooting
Trouble Shooting WARNING: For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan. TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit 1. -
Page 16: Repair Parts
Repair Parts BLADES SOLD SEPARATELY ETL Model No.: CF921... -
Page 17: How To Order Repair Parts
Repair Parts Listing Model Numbers Description CF921BS00 CF921CK00 CF921GES00 CF921ORB00 CF921VBN00 Hanger Ball Assembly, 761655-17 761655-23 761655-35 761655-32 761655-89 Consisting of: Hanger Bracket — — — — — Hanger Ball — — — — — Downrod (4.5”) — — — —... - Page 18 Notes ETL Model No.: CF921...
- Page 19 Notes ETL Model No.: CF921...
-
Page 20: Limited Warranty
You will be responsible for all insurance, freight or other transportation charges to our factory or authorized service center. Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage.