1. Manuals
  2. Brands
  3. Lekker Manuals
  4. Bicycle
  5. Jordaan+
  6. Assembly & maintenance manual

Lekker Jordaan+ Assembly & Maintenance Manual

Hide thumbs Also See for Jordaan+:
Table of Contents

Advertisement

Quick Links

Download this manual
Jordaan+

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Jordaan+ and is the answer not in the manual?

Questions and answers

Related Manuals for Lekker Jordaan+

Summary of Contents for Lekker Jordaan+

  • Page 1 Jordaan+...
  • Page 2 Assembly & Maintenance Guide Jordaan+...
  • Page 3 MANUAL LEKKER BIKES / Amsterdam GT MANUAL LEKKER BIKES / Amsterdam GT combination, tricks and available components. For this reason, our manual is only applicable to your new LEKKER bicycle and its assembly, alongside any important notes, warnings and maintenance guides. Assembly & Maintenance Guide...
  • Page 4 Index Getting started Fitting the saddle and handlebars Fitting the pedals Aligning the brakes Battery set-up Display settings Finishing touches Safety and warranty Assembly & Maintenance Guide Jordaan+...

  • Page 5: Getting Started

    So, without further ado, unbox your LEKKER bike and feast your eyes on your newest sidekick. Once you’- ve removed the packaging, make sure you have your trustly toolkit to hand, as shown in the illustration on the next page.
  • Page 6 Assembly & Maintenance Guide Jordaan+...
  • Page 7 02. Fitting the saddle and handlebars Saddle. Using a 5mm allen key, loosen the seatpost clamp bolt and adjust the seatpost height. Ensure it’s at the correct height for you, and tighten the bolt. Tip: Your knee should slightly bend when the pedal is at its lowest position while sitting on the saddle.

  • Page 8: Fitting The Pedals

    03. Fitting the pedals To assemble the pedals, you will need a 15mm open- RIGHT pedal: this pedal has no indented lines and is ended spanner. Insert the pedal into the crank and smooth in between the pedal and thread. ensure the pedals are properly tightened.

  • Page 9: Aligning The Brakes

    04. Aligning the brakes Lift the wheel off the ground and give it a spin. It should spin freely and without any noise. If you hear a metallic rubbing sound, then the brakes will need adjusting. To do this, you’ll need to use the 5mm allen key. With the bike upside down, adjust the caliper.

  • Page 10: Battery Set-Up

    05. Battery set-up Make sure that the battery is properly inserted into Note: All batteries and frames are water-resistant, the frame. When you feel a click, you’ll know it’s been but if you are storing the bike outside overnight, or locked into place.

  • Page 11: Display Settings

    06. Display Settings Once on, you can scroll through the 5 levels of motor We recommend that you sit on your bike before you assist using the + and - buttons on the front of the turn it on. This means you’ll have full control over the control module / display.

  • Page 12: Finishing Touches

    07. Finishing Touches Install the bell on your handlebars, in your preferred position. Generally, this is on the left hand side, next to the brake lever. Pump the tyres to 55-65 PSI If you’ve ordered any accessories such as racks, locks or lights, don’t forget to fit these too.

  • Page 13: Safety And Warranty

    Do not make any changes to your electric system or of a LEKKER product. If you want to use the warran- fit any other products to it, aimed at increasing the ty, please ensure you have your receipt and go to the power output from your eBike.
  • Page 14 Assembly & Jordaan+ Maintenance Guide lekkerbikes.com Assembly & Maintenance Guide...

This manual is also suitable for:

Jordaan gt 2021

Table of Contents