Advertisement
Quick Links
IPS Digital U-Type
Module
QUICK START GUIDE
For IPS U-Type Modules with USB, I2C, or RS232 communication protocols. See
Table 2 at end of document for list of supported models
Innovative Photonic Solutions 313 Enterprise Drive Plainsboro, NJ 08536
P: (732) 230-1591 W:
www.innovativephotonics.com
E:
sales@ipslasers.com
3.0v AB
Advertisement
Summary of Contents for IPS I0633SU0020PA-USB
- Page 1 IPS Digital U-Type Module QUICK START GUIDE For IPS U-Type Modules with USB, I2C, or RS232 communication protocols. See Table 2 at end of document for list of supported models Innovative Photonic Solutions 313 Enterprise Drive Plainsboro, NJ 08536 P: (732) 230-1591 W: www.innovativephotonics.com...
- Page 2 Initial Set-Up and Power On: Image 1: Side view of Digital U-Type Module 1. Connect power supply to the U-type module via the Molex connector To properly power the unit, connect the voltage source to pins 1 and 6. Connect GND to pins 5 and 10. Pins 1 and 6 must be tied together. Pins 5 and 10 must also be tied together.
- Page 3 4. Ensure the U-type module is recognized by the host system by opening the Windows® Device Manager. If using an alternate Operating System, please contact IPS for additional details on verifying device recognition. Locate “Ports (COM & LPT)” in the Device Manager. Ensure “USB Serial Device (COMX) is present.
- Page 4 5. Test the U-type module functionality Use a serial port monitor program to test the device functionality. The open source program "PuTTY" (https://www.putty.org/) can be used to test the device manually. 6. Before starting the session, configure the “Session” via the “Session” menu and setting the following: Verify the correct COM port is populated in the “Serial line”...
- Page 5 8. Ensure the device is correctly connected to the host system *Any text command needs to be entered within 10 seconds or the device will time out. This is a function of IPS’ firmware and is independent of terminal. Send the command "*IDN?"...
- Page 6 For a full list of command set instructions, please reference the “IPS Digital U-Type Technical Guidebook” located at: http://www.ipslasers.com/Digital U-Type Support/ v3.0 AB...
- Page 7 What is I2C? is a serial communication protocol typically used for short range high speed connections between multiple devices. It stands for the Inter-Integrated Circuit (IIC, or "I-squared- C") bus. Two wires are required for an I2C bus, SDA and SCL. Each device connects to the same two lines.
- Page 8 What Is RS-232? A minimal "3-wire" RS-232 connection consisting only of transmit data, receive data, and ground, is commonly used when the full facilities of RS-232 are not required. The RS-232 standard defines the voltage levels that correspond to logical one and logical zero levels for the data transmission and the control signal lines.
- Page 9 Table 1: Digital U-Type Molex 53014-1010 Connector Pinout (Mating connector part number: Molex 51004-1000) Pin Label Function Number Power Supply: 5V - 12 V. For lasers operating <600mW, a 5V minimum is required. For lasers operating ≥600mW, a minimum of 9V is required, 12V recommended.
- Page 10 HPU OEM Connector (Connector Part Number: 51004-1000) Pin Label Function Number Power supply, 5 - 12 V. Standard operation can use 5V. For units with > 1W output power, at least 9V is required. Pins 1 & 6 connected. Enable external laser power control through pin 8 (LD SET): ENABLE High = Disable Low = Enable...
- Page 11 Table 2: List of Standard Supported Models I0633SU0020PA-USB I0638MU0300MF-USB I0638SU0025PA-USB I0638MU0300MS-USB I0780SU0050PA-USB I0647MU0150MF-USB I0783SU0050PA-USB I0647MU0150MS-USB I07808U0050PA-USB I0680MU0300MF-USB I0830SU0050PA-USB I0680MU0300MS-USB I0976SU0220PA-USB I0785MU0350MF-USB I0976SU0500PA-USB I0785MU0350MS-USB I1030SU0100PA-USB I0785MU0500MF-USB I1030SU0250PA-USB I0785MU0500MS-USB I1053SU0050PA-IS-USB I0785MU1200MF-USB I1053SU0120PA-USB I0785MU1200MS-USB I1053SU0300PA-USB I0808MU0350MF-USB I1064SU0050PA-IS-USB I0808MU0350MS-USB I1064SU0120PA-USB I0808MU0500MF-USB I1064SU0300PA-USB I0808MU0500MS-USB I0808MU1200MF-USB...
Need help?
Do you have a question about the I0633SU0020PA-USB and is the answer not in the manual?
Questions and answers