Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Metallkraft RBM 305
Summary of Contents for Metallkraft RBM 305
- Page 1 Operating Instructions Plate rolling machine RBM 305 RBM 305...
-
Page 2: Table Of Contents
Passing on as well as copying of this document, the use and distribution of its content are prohibited if not explic- itly permitted. Contraventions are liable to compensa- tion. Subject to technical modifications and error. RBM 305 | Version 2.02... -
Page 3: Introduction
This combination of symbol and signal words indi- even further. cates a potentially dangerous situation which may lead to death or severe injury if not avoided. RBM 305 | Version 2.02... -
Page 4: Requirements To Staff
The protective gloves serve to protect the hands the responsiveness of which is affected by e. g. drugs, against sharp components as well as against fric- alcohol or medication, are not allowed to work with the tion, abrasions or deep injuries. machine. RBM 305 | Version 2.02... -
Page 5: General Safety Regulations
Use the right tool! Make sure the tools are not dull or damaged. The round bending machine RBM 305 is used exclusi- - Only use original spare parts and accessories to avoid vely for the production of round shaped parts such as pi- possible risks and risks of accidents. -
Page 6: Unintended Use
* Bending power ratings refer to S235JR with a tensile strength of 400 N / mm2 * Sheet bending capacity in VA = factor 0.75; Conical bending with half of the max. Sheet thickness possible RBM 305 | Version 2.02... -
Page 7: Description Of The Device
- There must be sufficient space for the operating personnel, for material transport as well as for ad- justment and maintenance work. Fig. 3: Description of the RBM 305 - The site must have good lighting. 1 Adjusting wheel guide roller (plate thickness) -
Page 8: Hazardous Areas
DANGER! - The operator should have a basic knowledge of this type of machine. - Operators should not wear wide garments, neck- laces, rings, etc. to prevent them from being pulled into the running machine. RBM 305 | Version 2.02... -
Page 9: Work Flow
It is advantageous to released and the upper roller must be removed from the insert the sheet only to then adjust the distance between guide. the two rollers so that they rest against the sheet. RBM 305 | Version 2.02... -
Page 10: Adjusting The Guide Pulley
It should be noted that a small radius is made by repeating the bending process several times; Once too much bent, this step can not be undone. Fig. 11: Bending chart RBM 305 | Version 2.02... - Page 11 Conical bending is more difficult than normal bending. tion. The machine performance is reduced by 30% to 50%, the conical bending capacity decreases by about 25%. The material thickness must be reduced accordingly. RBM 305 | Version 2.02...
-
Page 12: Bending Wires
Before servicing and maintaining the plate rolling machine, the maintenance instructions must be care- fully read. The handling of the plate rolling machine is only permitted to persons who are familiar with the plate rolling machine. Fig. 16: Swivel guide roller RBM 305 | Version 2.02... -
Page 13: Cleaning And Maintenance
The Plate rolling Machine does not 1. The material thickness could be 1. Check the material to be bent. bend the materials as indicated in the wrong. 2. Contact the dealer. catalog. 2. The mechanics are faulty. RBM 305 | Version 2.02... -
Page 14: Disposal, Recycling Of Used Devices
If necessary, ask for the product-specific data The hand crank for the plate rolling machine RBM 305 sheets. has to be ordered. This is indicated in the spare parts drawing with the item number 16. -
Page 15: Spare Parts Drawing
In case of service, the following drawing shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 19: Spare parts Drawing RBM 305 RBM 305 | Version 2.02... -
Page 16: Declaration
RBM 305 Name of the machine: Plate rolling machine Machine type: Item number: 3780112 Serial number: ___________________ 20____ Year of Manufacturer: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26 Responsible for documentation D-96103 Hallstadt Hallstadt, 03.05.2014 ______________________ Kilian Stürmer Manager RBM 305 | Version 2.02... -
Page 17: Notes
Notes 14 Notes RBM 305 | Version 2.02... - Page 18 www.metallkraft.de...
Need help?
Do you have a question about the RBM 305 and is the answer not in the manual?
Questions and answers