Indesit Hotpoint HCD662UK Service Information
  1. Manuals
  2. Brands
  3. Indesit Manuals
  4. Dishwasher
  5. Hotpoint HCD662UK
  6. Service information

Indesit Hotpoint HCD662UK Service Information

Table top dishwasher
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Service
Information
© 2014 Reg. Office: Peterborough PE2 9JB Registered in London: 106725
Indesit Company UK Ltd
5407820 Issue 1
SM003940 ~ C00305547
HOTPOINT
TABLE TOP
DISHWASHER
Model Covered
HCD662UK
May 2014
84419

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hotpoint HCD662UK and is the answer not in the manual?

Questions and answers

Related Manuals for Indesit Hotpoint HCD662UK

Summary of Contents for Indesit Hotpoint HCD662UK

  • Page 1 5407820 Issue 1 May 2014 SM003940 ~ C00305547 HOTPOINT TABLE TOP DISHWASHER Model Covered HCD662UK 84419 Service Information Indesit Company UK Ltd © 2014 Reg. Office: Peterborough PE2 9JB Registered in London: 106725...
  • Page 2 Indesit Company SAFETY NOTES & GENERAL SERVICING ADVICE 1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance. 2. It should ONLY be used by suitably qualified persons having technical competence applicable product knowledge and suitable tools and test equipment.

  • Page 3: Table Of Contents

    Indesit Company INDEX Safety Notes & General Servicing Advice........ii Index .

  • Page 4: Technical Specifications

    Indesit Company TECHNICAL SPECIFICATIONS Model HCD662UK - White - Commercial Code 84419 First produced 2014 Country of Manufacture China Dimensions Width - 550 mm Height - 440 mm Depth - 525 mm Energy A+ (2011, EU 1998 or other deicated regulations.)

  • Page 5: General Information / Installation

    Indesit Company GENERAL INFORMATION A six place Table Top Dishwasher with 6 wash cycles. The Programme Selector, buttons and LED indicators are mounted on the console. Any faults are indicated by beeping and the LEDs flashing quickly on the Console.

  • Page 6: Preparing The Machine For Use

    Indesit Company PREPARING THE MACHINE FOR USE Adding Salt for the First Time 1. Open the door and the remove the basket. 2. The Salt Pot is located on the left hand side of the bottom of the tank. 3. Remove the salt pot lid, by turning anticlockwise.

  • Page 7: Introduction

    Introduction Hotpoint Compact electrical dishwasher with 6 washing cycles offers good washing performance to satisfy every washing requirement. Its electronic control is easy and convenient to operate. The rack can hold up to 6 sets of dishes. The size (width * depth * height: 550mm * 500mm * 438mm) can easily fit in any corner of the kitchen, and it’s recommended to locate at which the water hose connection is accessible.

  • Page 8: Component Locator Views

    Component Locator Views Front View Interior View (with basket) Part Name: 1 – cutlery basket 2 – basket 3 – dispenser Interior View (With Basket Removed)

  • Page 9: Dishwasher Components

    Part Name: 1 – Nut of air breather 2 – Nut of siphon 3 – Cover of softener 4 – Sprayer 5 – Filter System Back View Drain Hose Inlet Hose Connecter Part Name: 1 – Backboard 2 – Hollow plate 3 – Bottom board 4 – Power cord Dishwasher Components Note : Throughout this manual, features and appearance may vary from your model.

  • Page 10: Main Control Board

    Main control board The main control board controls all electrical elements in the dishwasher machine. It located in the protecting box in the bottom of dishwasher machine. And it easy is replaced when it cannot work. Removal and Replacement 1. Disconnect power supply. 2.

  • Page 11: Dispenser

    2. Hold on outer door assembly. Remove all screws for fixing the operating board. Screws Part Name: 1 – outer door 2 – handle cover 3 – operating board Caution : Inner door of edges are sharp. Some corners and edges of parts are sharp. 3.

  • Page 12: Door Handle Assembly

    path of the connecting rod. This action moves the cover catch and releases the detergent cover. When deactivated, the lever resets to rest under the notch in the center of the connecting rod. When activated for the second time in a cycle, the lever lifts the connecting rod by the notch, lifting the rinse dispenser plunger and releasing the rinse agent.

  • Page 13: Microswitch (Door Handle Assembly)

    4. Remove all screws for fixing door handle assembly. Screws Snap-fits 5. Reverse the above procedure to install. And check out all connectors connects well. Microswitch (door handle assembly) The microswitch connects a forceful electric power. All loads of the dishwasher are series connection with microswitch.

  • Page 14: Shell

    Screws 4. Remove dispenser. (see dispenser removal and replacement) 5. Remove door handle assembly. (see door handle assembly removal and replacement) 6. Reverse the above procedure to install. And check out all connectors connects well. Shell Removal and Installation 1. Take off cutlery basket, basket and filter system. 2.

  • Page 15: Operating Board

    Part Name: 1 – corner board 2 – absorber 3 – backboard 4 – hollow plate Operating board Removal and Replacement 1. Disconnect power supply. 2. Remove shell. (see shell removal and installation) 3. Take out two corner boards, absorber sound, backboard, hollow plate. 4.

  • Page 16: Siphon

    Clamp Gasket of air breather Siphon Removal and Replacement Remove shell. (see shell removal and installation) Take out two corner boards, absorber sound, backboard, hollow plate. Contrarotate nut of siphon. Take out one way valve and gasket of siphon. Part name: 1 – nut of siphon 2 – gasket of siphon 3 – one way valve Remove two clamps for fixing connecting hoses with siphon.

  • Page 17: Tank Assembly

    Part name: 1 – sheet copper 2 – pressure switch hose 3 – pressure switch Unfix the snap-fit of bottom board for fixing pressure switch. And pull out pressure Snap-fits switch hose. Pull out all terminals of of bottom pressure switch board Note: mark all terminals’...
  • Page 18 Plug terminal of Ring terminals tank assembly Screw and nut Unfix the sheet copper for fixing the pressure switch hose. (see pressure switch removal and replacement) Remove two screws for fixing spray holder, then take out the spray holder. Screws Part name: 1 –...

  • Page 19: Sump Assembly

    4 – left front chamber bracket 13. Reverse the above procedure to install. And check out all connectors connects well. Sump assembly Part Name: 1 – motor pump assembly 2 – thermal resistor 3 – drain pump assembly 4 – sump 5 – check plate holder 6 –...

  • Page 20: Drain Pump Assembly

    Ring Terminals Terminal Connector Terminals Remove one clamp for fixing connecting hose to check plate holder. Clamp Pull out hose for connecting water softener to sump assembly. And pull out pressure switch hose. Part name: 1 – connecting hose (water softener) 2 –...

  • Page 21: Motor Pump Assembly

    Reverse the above procedure to install. And check out all connectors connects well. Motor pump assembly Removal and replacement Take out sump assembly. (see sump assembly removal and installation) Remove all screws for fixing sump pump assembly. Screws Replace a new motor pump assembly. Reverse the above procedure to install.

  • Page 22: Heater Elements Support Assembly

    screws Reverse the above procedure to install. And check out all connectors connects well. Heater elements support assembly Removal and replacement Take out sump assembly. (see sump assembly removal and installation) Remove heater elements assembly. (see heater elements assembly removal and replacement) Take out gasket of heater elements support assembly.

  • Page 23: Flowmeter

    Pull out check plate from check plate holder, and replace a new check plate. Reverse the above procedure to install. And check out all connectors connects well. Flowmeter Flowmeter is an instrument for monitoring, measuring the rate of flow. Main control board control inlet valve to be on / off according signal of flowmeter.

  • Page 24: Floater Assembly

    Reverse the above procedure to install. And check out all connectors connects well. Floater assembly Part name: 1 – floater holder 2 – microswitch (floater assembly) 3 – floater Removal and Installation Take off cutlery basket, basket and filter system. Remove shell.
  • Page 25 Terminals Part name 1 – air breather 2 – O ring 3 – gasket of water softener 4 – water softener 5 – connecting hose (water softener) Removal and replacement Take off cutlery basket, basket and filter system. Remove shell. (see shell removal and installation) Take out two corner boards, absorber sound, backboard, hollow plate.
  • Page 26 Troubleshooting SYMPTOM CHECK FOR THE FOLLOWING REMEDY 3 in 1 lamp The water supply is turned off. Turn the water supply on. twinkle Defective water fill valve. Replace the water fill valve. Dishwasher Low water pressure. Minimum water pressure of 20 PSI. will not fill with Disassemble and clean the water fill valve and Obstructed water fills valve or hose.
  • Page 27 Repeated dishwasher Defective PCB assembly Replace the PCB assembly cycles. Water remains This is necessary to keep the pump primed and is A small amount of water (in sump area) is in bottom drained automatically at the beginning of each normal.
  • Page 28 — — ——...

This manual is also suitable for:

84419

Table of Contents